Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER

FRONT SUSPENSION MEMBER > REMOVAL

for Preparation Click here



1. REMOVE FRONT FRAME ASSEMBLY
for 2GR-FE: (Click here)
for 2AR-FE: (Click here)


2. REMOVE FRONT ENGINE MOUNTING INSULATOR ASSEMBLY (for 2GR-FE)



3. REMOVE FRONT ENGINE MOUNTING INSULATOR (for 2AR-FE)



4. REMOVE ENGINE MOUNTING INSULATOR LH
for 2GR-FE:
for 2AR-FE:


5. REMOVE ENGINE MOUNTING INSULATOR RH
for 2GR-FE:
for 2AR-FE:


6. REMOVE FRONT NO. 1 STABILIZER BRACKET LH


    C238973
  1. Remove the 2 bolts and front No. 1 stabilizer bracket LH from the front frame assembly.



7. REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:
Perform the same procedure as the LH side.



8. REMOVE FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY
  1. Remove the front stabilizer bar with 2 front stabilizer link assemblies from the front frame assembly.



9. REMOVE STEERING LINK ASSEMBLY


    C238515
  1. Remove the 2 bolts, 2 nuts and steering link assembly.

    NOTICE:
    Keep the nut from rotating while turning the bolt because the nut has its own stopper.



10. REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH


    C167143
  1. Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly from the front frame assembly.

    NOTICE:
    When removing the bolt, keep the nut from rotating.

  1. Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly.



11. REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Perform the same procedure as the LH side.



12. REMOVE FRONT SUSPENSION MEMBER DYNAMIC DAMPER


    C221242
  1. Remove the 2 bolts and front suspension member dynamic damper from the front frame assembly.



13. REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER
  1. Remove the 2 front suspension member body mounting front stoppers from the front frame assembly.



14. REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER
  1. Remove the 2 front suspension member body mounting rear stoppers from the front frame assembly.



15. REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION


    C169231E03
  1. Install SST as shown in the illustration.

    SST
    09830-10010   (09830-01010, 09830-01040, 09830-01050)
    09950-40011   (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)
    Text in Illustration 
    *1
    Front Suspension Member Body Mounting Front Cushion



    C167146E05
  1. Using SST, remove the front suspension member body mounting front cushion from the front frame assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    NOTICE:
    1. Make sure that the claws of SST are securely hung onto the mounting cushion.
    2. Tighten SST slowly and evenly.
    3. Be careful as the mounting cushion may fly out.
    4. The mounting cushion cannot be reused.



16. REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH


    C169231E03
  1. Install SST as shown in the illustration.

    SST
    09830-10010   (09830-01010, 09830-01040, 09830-01050)
    09950-40011   (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)
    Text in Illustration 
    *1
    Front Suspension Member Body Mounting Rear Cushion LH



    C167149E05
  1. Using SST, remove the front suspension member body mounting rear cushion LH from the front frame assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    NOTICE:
    1. Make sure that the claws of SST are securely hung onto the mounting cushion.
    2. Tighten SST slowly and evenly.
    3. Be careful as the mounting cushion may fly out.
    4. The mounting cushion cannot be reused.



17. REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH

HINT:
Perform the same procedure as the LH side.



18. REMOVE HOLE PLUG
  1. Remove each hole plug from the front frame assembly.