Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1436    Yaw Rate Sensor Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when the skid control ECU detects improper installation of the yaw rate and acceleration sensor (for separate type) or yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type) or an abnormality in the difference between the yaw rate sensor value and the control value estimated based on the acceleration sensor, steering angle sensor and speed sensor signals.

DTC No.
DTC Detection Condition
Trouble Area
C1436
Difference between the yaw rate sensor value and the control value estimated inside the skid control ECU is abnormal.
  1. Sensor installation
  2. Yaw rate and acceleration sensor (for separate type)
  3. Yaw rate and acceleration sensor (Airbag sensor assembly) (for built-in type)

INSPECTION PROCEDURE

1.CONFIRM YAW RATE AND ACCELERATION SENSOR TYPE
  1. Confirm the yaw rate and acceleration sensor type.

    Result:

    Result
    Proceed to
    Yaw rate and acceleration sensor (for separate type)
    A
    Yaw rate and acceleration sensor (airbag sensor assembly) (for built-in type)
    B



B
Go to step 5
A


2.READ VALUE USING TECHSTREAM (YAW RATE AND ACCELERATION SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List using the Techstream (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Yaw Rate Sensor
    Yaw rate sensor / Min.: -128 degrees/s, Max.: 127 degrees/s
    Vehicle stopped: 0 degrees/s
    Turning right: -128 to 0 degrees/s
    Turning left: 0 to 127 degrees/s
    -

  1. Check that the yaw rate and acceleration sensor output value displayed on the Techstream.

    Result:

    Result
    Proceed to
    NG (The yaw rate and acceleration sensor output value is 0 degrees/s when the vehicle is stationary, but the value fluctuates when turning.)
    A
    NG (The yaw rate and acceleration sensor output value is not 0 degrees/s when the vehicle is stationary.)
    B
    OK
    C

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



B
REPLACE YAW RATE AND ACCELERATION SENSOR (Click here)

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


3.CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION
  1. Turn the ignition switch off.

  1. Drive the vehicle straight ahead at 50 km/h (31 mph) or more for at least 30 seconds.

  1. Check that the steering wheel is correctly centered while driving straight ahead.

    HINT:
    If front wheel alignment and steering are adjusted as a result of an off-center steering wheel, acquire the yaw rate and acceleration sensor zero point again after the adjustments are completed.

    OK:
    The steering wheel is correctly centered.



NG
ADJUST FRONT WHEEL ALIGNMENT OR STEERING (Click here)
OK


4.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION
  1. Check that the yaw rate and acceleration sensor has been installed properly (Click here).

    OK:
    The sensor should be tightened to the specified torque.
    The sensor should not be installed in a tilted position.

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY (Click here)
OK

REPLACE YAW RATE AND ACCELERATION SENSOR (Click here)  

5.READ VALUE USING TECHSTREAM (YAW RATE AND ACCELERATION SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List using the Techstream (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Yaw Rate Sensor
    Yaw rate sensor / Min.: -128 degrees/s, Max.: 127 degrees/s
    Vehicle stopped: 0 degrees/s
    Turning right: -128 to 0 degrees/s
    Turning left: 0 to 127 degrees/s
    -

  1. Check that the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the Techstream.

    Result:

    Result
    Proceed to
    NG (The yaw rate and acceleration sensor (airbag sensor assembly) output value is 0 degrees/s when the vehicle is stationary, but the value fluctuates when turning.)
    A
    NG (The yaw rate and acceleration sensor (airbag sensor assembly) output value is not 0 degrees/s when the vehicle is stationary.)
    B
    OK
    C

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



B
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


6.CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION
  1. Turn the ignition switch off.

  1. Drive the vehicle straight ahead at 50 km/h (31 mph) or more for at least 30 seconds.

  1. Check that the steering wheel is correctly centered while driving straight ahead.

    HINT:
    If front wheel alignment and steering are adjusted as a result of an off-center steering wheel, acquire the yaw rate and acceleration sensor zero point again after the adjustments are completed.

    OK:
    The steering wheel is correctly centered.



NG
ADJUST FRONT WHEEL ALIGNMENT OR STEERING (Click here)
OK


7.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
  1. Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly (Click here).

    OK:
    The sensor should be tightened to the specified torque.
    The sensor should not be installed in a tilted position.

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
INSTALL AIRBAG SENSOR ASSEMBLY CORRECTLY (Click here)
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)