FRONT DOOR LOCK > INSTALLATION |
| 1. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY |
![]() |
Install the front door inside locking cable assembly.
![]() |
Engage the 3 claws.
| 2. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY |
![]() |
Install the front door lock remote control cable assembly.
| 3. INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY |
Apply MP grease to the sliding parts of the front door lock with motor assembly.
When reusing the front door lock with motor assembly.
Install a new door lock wiring harness seal to the front door lock with motor assembly.
![]() |
Insert the front door lock open rod to the front door lock with motor assembly.
| *1 | Front Door Lock Open Rod |
Make sure that the front door lock open rod is securely connected to the front door lock with motor assembly.
Using a T30 "TORX" socket wrench, install the front door lock with motor assembly with the 3 screws.
| 4. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (w/ Lock Cylinder) |
![]() |
Using a T30 "TORX" socket wrench, install the front door outside handle cover with lock cylinder assembly with the screw.
![]() |
Install the hole plug.
| 5. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY |
![]() |
Engage the guide as shown in the illustration.
Install the front door rear lower frame sub-assembly with the 2 bolts.
| 6. INSTALL FRONT DOOR GLASS RUN |
![]() |
Install the front door glass run.
| 7. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY |
Connect the cable to the negative (-) battery terminal.
Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the power window regulator master switch assembly.
![]() |
Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.
![]() |
Install the front door glass sub-assembly with the 2 bolts.
![]() |
Install the grommet.
| 8. INSTALL FRONT DOOR SERVICE HOLE COVER |
Apply new butyl tape to the front door panel.
![]() |
Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
| *1 | Reference Point |
Attach the front door service hole cover according to the reference points on the front door panel.
Engage the 5 clamps.
Install the bolt.
Connect each connector.
| 9. INSTALL DOOR SIDE AIRBAG SENSOR |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

| *a | Incorrect | *b | Correct |
Insert the pin (stopper) into the door hole and install the door side airbag sensor to the front door panel with the bolt.
Connect the connector to the door side airbag sensor.
Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

| *1 | White Housing Lock | *2 | Yellow CPA |
| *a | Connection is Completed | - | - |
Check that there is no looseness in the installation parts of the door side airbag sensor.
| 10. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP |
![]() |
Install the front door inner glass weatherstrip.
| 11. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Connect the front door lock remote control cable assembly and front door inside locking cable assembly.
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
![]() |
Engage the front door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.
| *1 | Reference Boss |
![]() |
Engage the 10 clips and install to front door trim board sub-assembly.
Install the 3 screws.
If protective tape has been applied, remove it.
| 12. INSTALL COURTESY LIGHT ASSEMBLY |
Connect the connector.
![]() |
Engage the claw to install the courtesy light assembly.
| *A | for LH Side |
| *B | for RH Side |
| 13. INSTALL FRONT ARMREST ASSEMBLY |
![]() |
Engage the 2 guides, 3 clips and 7 claws, and install the front armrest assembly.
| 14. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side) |
Connect each connector.
![]() |
Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator master switch assembly with front door armrest base panel.
| 15. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side) |
Connect each connector.
![]() |
Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator switch assembly with front door armrest base panel.
| 16. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH |
![]() |
Engage the 3 clips to install the front door lower frame bracket garnish.
| 17. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Engage the 3 claws to install the front door inside handle bezel plug.
| 18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 19. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side) |
| 20. CHECK POWER WINDOW CONTROL SYSTEM |
| 21. INSPECT SRS WARNING LIGHT |