REAR DOOR LOCK > INSTALLATION |
| 1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY |
![]() |
Install the rear door inside locking cable assembly.
![]() |
Engage the 3 claws.
| 2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY |
![]() |
Install the rear door lock remote control cable assembly.
![]() |
Engage the claw.
| 3. INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY |
Apply MP grease to the sliding parts of the rear door lock with motor assembly.
When reusing the rear door lock with motor assembly.
Install a new door lock wiring harness seal to the rear door lock with motor assembly.
![]() |
Insert the rear door lock with motor assembly to the rear door outside handle release plate, and set it to the rear door panel.
| *1 | Release Plate |
Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock with motor assembly.
Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.
| 4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Slide the rear door glass sub-assembly to install it as shown in the illustration.
| 5. INSTALL REAR DOOR QUARTER WINDOW GLASS |
Install the rear door quarter window glass to the rear door quarter window weatherstrip.
![]() |
Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.
| 6. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY |
![]() |
Install the rear door lower window frame sub-assembly with the screw and 2 bolts.
| 7. INSTALL REAR DOOR GLASS RUN |
![]() |
Install the rear door glass run.
| 8. INSTALL REAR DOOR WEATHERSTRIP |
![]() |
Install the upper part of rear door weatherstrip as shown in the illustration.
| 9. INSTALL REAR DOOR SERVICE HOLE COVER |
Apply new butyl tape to the rear door panel.
![]() |
Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.
| *1 | Reference Point |
Attach the rear door service hole cover according to the reference points on the rear door panel.
Connect the connector.
| 10. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP |
![]() |
Install the rear door inner glass weatherstrip.
| 11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Install the No. 1 door scuff plate clamp as shown in the illustration.
![]() |
Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.
| *1 | Rear Door Inside Locking Cable Assembly |
| *2 | Rear Door Lock Remote Control Cable Assembly |
![]() |
Engage the rear door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.
| *1 | Reference Boss |
![]() |
Engage the 8 clips and install the rear door trim board sub-assembly.
Install the 3 screws.
If protective tape has been applied, remove it.
| 12. INSTALL REAR ARMREST ASSEMBLY |
![]() |
Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.
| 13. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL |
Connect the connector.
![]() |
Engage the 4 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.
| 14. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Engage the 3 claws to install the rear door inside handle bezel plug.
| 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 16. CHECK POWER WINDOW CONTROL SYSTEM |