Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY

FRONT SEAT SIDE AIRBAG ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL FRONT SEAT AIRBAG ASSEMBLY

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the front seatback frame sub-assembly or separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.

  1. Install the front seat airbag assembly with 2 new nuts.

    Torque:
    for TMMK Made:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    for SIA Made:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the 2 clamps.



2. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for TMMK Made Manual Seat)
  1. Temporarily install the separate type front seatback cover with pad.

  1. Engage the 4 claws to install the 2 front seat headrest supports.

  1. Engage the 2 hooks.

    CAUTION:
    1. For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
    2. Make sure that the strap is not twisted after engaging the 2 hooks.
    3. Engage the 2 hooks securely.


    1. Slide each hook to engage them.

    2. Install the 4 clips.

  1. Engage the 2 fasteners.

  1. Engage the hook.



3. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for SIA Made Manual Seat)
  1. Temporarily install the separate type front seatback cover with pad.

  1. Engage the 4 claws to install the 2 front seat headrest supports.

  1. Install the 3 brackets with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    1. For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
    2. Make sure that the strap is not twisted after installing the nut.
    3. Install the bracket securely.



    B288591
  1. Turn back the separate type front seatback cover.

  1. Using hog ring pliers, install the 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B280215
  1. Using hog ring pliers, install 3 new hog rings.



    B280213
  1. Using hog ring pliers, install 5 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



4. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for TMMK Made Power Seat)
  1. Temporarily install the separate type front seatback cover with pad.

  1. Engage the 4 claws to install the 2 front seat headrest supports.

  1. Engage the 2 hooks.

    CAUTION:
    1. For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
    2. Make sure that the strap is not twisted after engage the 2 hooks.
    3. Engage the 2 hooks securely.


    1. Slide each hook to engage them.

    2. Install the 4 clips.

  1. Engage the 2 fasteners.

  1. Engage the hook.



5. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for SIA Made Power Seat)
  1. Temporarily install the separate type front seatback cover with pad.

  1. Engage the 4 claws to install the 2 front seat headrest supports.

  1. Install the 3 brackets with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    1. For vehicles with side airbags, the separate type front seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
    2. Make sure that the strap is not twisted after installing the nut.
    3. Install the bracket securely.



    B288591
  1. Turn back the separate type front seatback cover.

  1. Using hog ring pliers, install the 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B281114
  1. Using hog ring pliers, install 3 new hog rings.

    NOTICE:
    When installing the hog rings, take care to minimize wrinkles as much as possible.



    B281111
  1. Using hog ring pliers, install 5 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



6. CONNECT AIRBAG WIRE HARNESS (for TMMK Made Manual Seat)
  1. Engage the claw and 3 clamps to connect the airbag wire harness.

  1. Connect the 2 rubber bands of the separate type front seatback cover with pad.



7. CONNECT AIRBAG WIRE HARNESS (for SIA Made Manual Seat)
  1. Engage the claw and 3 clamps to connect the airbag wire harness.

  1. Engage the fastener to connect the airbag wire harness.

  1. Connect the rubber band of the separate type front seatback cover with pad.



8. CONNECT AIRBAG WIRE HARNESS (for TMMK Made Power Seat)


  1. w/ Seat Heater System:



      B280156E01
    1. Connect the connector (E).

    2. Engage the clamp (F).

  1. Engage the claw (D) and 3 clamps (C) to Connect the airbag wire harness.

  1. Engage the clamp (B).

  1. Connect the connector (A).

  1. Connect the 2 rubber bands of the separate type front seatback cover with pad.



9. CONNECT AIRBAG WIRE HARNESS (for SIA Made Power Seat)
  1. w/ Seat Heater System:

    1. Connect the connector.

    2. Engage the clamp.

  1. Engage the claw and 3 clamps to Connect the airbag wire harness.

  1. Engage the fastener to connect the airbag wire harness.

  1. Connect the rubber band of the separate type front seatback cover with pad.



10. INSTALL FRONT SEAT ASSEMBLY (for TMMK Made Manual Seat)
(Click here)


11. INSTALL FRONT SEAT ASSEMBLY (for SIA Made Manual Seat)
(Click here)


12. INSTALL FRONT SEAT ASSEMBLY (for TMMK Made Power Seat)
(Click here)


13. INSTALL FRONT SEAT ASSEMBLY (for SIA Made Power Seat)
(Click here)


14. PERFORM DIAGNOSTIC SYSTEM CHECK
for Separate Type Yaw Rate Sensor: (Click here)
for Built-in Type Yaw Rate Sensor: (Click here)