Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2012.02–2015.04
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM J

2GR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM. When the ignition switch to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually. When the ignition switch is turned ON, the MIL should be illuminated and should then turn off after engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A266858E09
0.656,0.531 0.75,0.688 0.094,0.156 10 false 5 0.844,0.531 1.25,0.771 0.406,0.24 10 false AM2 1.927,0.521 2.021,0.677 0.094,0.156 10 false 6 1.594,0.521 1.833,0.677 0.24,0.156 10 false IG2 0.646,1.031 0.906,1.188 0.26,0.156 10 false I36 0.646,1.198 3,1.479 2.354,0.281 10 false Ignition or Starter Switch Assembly*1 0.563,1.677 1.083,1.833 0.521,0.156 10 false ST/AM2 0.854,2.417 1.531,2.563 0.677,0.146 10 false IG2-MAIN 0.615,3.49 1.344,3.729 0.729,0.24 10 false FL MAIN 0.74,4.573 1.25,4.885 0.51,0.313 10 false Battery 2.219,3.438 3.708,3.698 1.49,0.26 10 false No. 1 Integration Relay 2.417,4.833 4.76,5.115 2.344,0.281 10 false *1: w/o Smart Entry and Start System 2.417,5.188 4.708,5.521 2.292,0.333 10 false *2: w/ Smart Entry and Start System 2.427,3.104 2.667,3.26 0.24,0.156 10 false IG2 1.948,2.281 2.146,2.438 0.198,0.156 10 false 1D 1.99,2.104 2.083,2.26 0.094,0.156 10 false 3 1.948,2.771 2.146,2.927 0.198,0.156 10 false 1E 1.99,2.604 2.083,2.76 0.094,0.156 10 false 2 3.76,2.271 3.958,2.427 0.198,0.156 10 false 1C 3.802,2.115 3.896,2.271 0.094,0.156 10 false 5 2.948,1.823 3.146,1.979 0.198,0.156 10 false 1C 3.073,2.01 3.167,2.167 0.094,0.156 10 false 8 4.271,2.417 5.042,2.573 0.771,0.156 10 false METER-IG2 4.469,0.458 4.781,0.698 0.313,0.24 10 false *2 5.031,2.188 5.229,2.344 0.198,0.156 10 false 13 5.313,2.188 5.573,2.344 0.26,0.156 10 false IG+ 6.406,2.188 6.583,2.344 0.177,0.156 10 false 22 6,2.188 6.323,2.344 0.323,0.156 10 false CHK 4.688,2.771 4.958,2.927 0.271,0.156 10 false I18 4.688,2.938 6.51,3.229 1.823,0.292 10 false Combination Meter Assembly 5.583,1.177 5.854,1.333 0.271,0.156 10 false A43 5.583,1.344 7.146,1.792 1.563,0.448 10 false Certification ECU (Smart Key ECU Assembly)*2 5.771,0.521 5.865,0.677 0.094,0.156 10 false 9 5.948,0.604 6.292,0.76 0.344,0.156 10 false IG2D 2.021,0.74 3,0.896 0.979,0.156 10 false ECU-IG2 NO. 1 5.688,3.917 5.948,4.198 0.26,0.281 10 false 27 5.948,3.938 6.104,4.094 0.156,0.156 10 false W 6.313,4.979 6.635,5.135 0.323,0.156 10 false ECM 5.969,4.979 6.24,5.135 0.271,0.156 10 false A25 2.75,0.458 3.063,0.698 0.313,0.24 10 false *1 2.198,0.458 2.51,0.698 0.313,0.24 10 false *1 0.219,1.375 0.531,1.615 0.313,0.24 10 false *1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.


Result:
Result Proceed to
MIL remains ON A
MIL does not illuminate B



A

2.CHECK WHETHER DTC OUTPUT RECURS

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.

Powertrain > Engine > Trouble Codes
50001 234

e.

Check if any DTCs have been detected. Note down any DTCs.

Result:
Result Proceed to
DTC is not output A
Any DTCs is output B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.




A

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

B

REPAIR CIRCUIT INDICATED BY OUTPUT DTC

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.
A255690C26
0.479,0.969 0.969,1.26 0.49,0.292 0.26,0.156 0.625,0.552 0.365,0.396 10 *a 0.615,1.031 0.969,1.333 0.354,0.302 10 A25
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-22 (CHK) or A25-27 (W) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turned to ON.

OK:

MIL should be illuminated.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The intelligent tester cannot communicate with the ECM.




A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-22 (CHK) - A25-27 (W) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR