Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM J

2GR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V power source voltage from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646E12
1.333,0.823 2.646,1.115 1.313,0.292 10 false from EFI NO. 1 Fuse 1.333,1.167 2.646,1.469 1.313,0.302 10 false from EFI NO. 2 Fuse 0.156,1.885 2.646,2.385 2.49,0.5 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.198,2.719 2.635,3.125 2.438,0.406 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.979,3.094 5.323,3.406 0.344,0.313 10 false ECM 2.885,0.729 3.5,1.031 0.615,0.302 10 false BATT 2.823,1.083 3.448,1.292 0.625,0.208 10 false +B, +B2 3.083,1.99 3.365,2.177 0.281,0.188 10 false VC 4.406,0.896 6.198,1.25 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.396,1.792 6.385,2.146 0.99,0.354 10 false Microprocessor 4.083,2.833 4.417,3.125 0.333,0.292 10 false R

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are deactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated when the ignition switch is turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A257906E01
2.481,4.25 2.587,4.406 0.106,0.156 10 3 2.481,3.891 2.587,4.048 0.106,0.156 10 2 2.481,3.528 2.587,3.684 0.106,0.156 10 1 2.091,5.827 2.401,5.986 0.311,0.16 10 VC2 2.132,5.437 2.443,5.597 0.311,0.16 10 EX- 2.118,5.096 2.429,5.256 0.311,0.16 10 EX+ 0.427,5.072 0.705,5.214 0.278,0.142 10 E59 0.427,5.24 2.042,5.552 1.615,0.313 10 VVT Sensor (for Exhaust Camshaft of Bank 2) 2.481,2.777 2.587,2.933 0.106,0.156 10 3 2.481,2.412 2.587,2.569 0.106,0.156 10 2 2.481,2.044 2.587,2.2 0.106,0.156 10 1 2.118,4.346 2.429,4.506 0.311,0.16 10 VC2 2.132,3.977 2.443,4.137 0.311,0.16 10 EX- 2.118,3.607 2.429,3.767 0.311,0.16 10 EX+ 0.427,3.596 0.705,3.738 0.278,0.142 10 E53 0.427,3.764 2.033,4.101 1.606,0.337 10 VVT Sensor (for Exhaust Camshaft of Bank 1) 0.427,0.653 0.705,0.796 0.278,0.142 10 E54 0.427,0.822 1.964,1.158 1.536,0.337 10 VVT Sensor (for Intake Camshaft of Bank 1) 2.034,0.674 2.429,0.834 0.394,0.16 10 VVR+ 2.189,1.374 2.43,1.533 0.241,0.16 10 VC 2.048,0.992 2.443,1.151 0.394,0.16 10 VVR- 2.481,1.312 2.587,1.468 0.106,0.156 10 3 2.481,0.948 2.587,1.104 0.106,0.156 10 2 2.481,0.593 2.587,0.75 0.106,0.156 10 1 4.984,0.479 5.204,0.635 0.22,0.156 10 81 4.933,1.214 5.208,1.371 0.275,0.156 10 111 4.919,0.84 5.222,0.997 0.303,0.156 10 110 4.979,3.419 5.198,3.575 0.22,0.156 10 79 4.979,4.902 5.198,5.058 0.22,0.156 10 80 4.924,0.655 5.203,0.811 0.278,0.156 10 E26 4.924,1.385 5.203,1.541 0.278,0.156 10 E26 4.924,1.018 5.203,1.174 0.278,0.156 10 E26 4.924,3.596 5.203,3.752 0.278,0.156 10 E26 4.921,5.074 5.206,5.23 0.284,0.156 10 E26 5.271,0.646 5.665,0.806 0.394,0.16 10 VV1+ 5.271,1.294 5.665,1.453 0.394,0.16 10 VCV1 5.277,0.928 5.671,1.088 0.394,0.16 10 VV1- 5.277,3.614 5.671,3.774 0.394,0.16 10 EV1+ 5.282,5.083 5.676,5.243 0.394,0.16 10 EV2+ 5.772,6.232 6.116,6.391 0.343,0.16 10 ECM 4.924,2.125 5.203,2.281 0.278,0.156 10 E26 4.981,1.948 5.201,2.104 0.22,0.156 10 78 5.271,2.131 5.665,2.291 0.394,0.16 10 VV2+ 0.427,2.139 0.705,2.281 0.278,0.142 10 E60 0.427,2.307 1.95,2.643 1.523,0.337 10 VVT Sensor (for Intake Camshaft of Bank 2) 2.034,2.145 2.429,2.305 0.394,0.16 10 VVL+ 2.048,2.491 2.443,2.65 0.394,0.16 10 VVL- 2.179,2.851 2.43,3.026 0.251,0.175 10 VC 2.481,5.721 2.587,5.877 0.106,0.156 10 3 2.481,5.362 2.587,5.519 0.106,0.156 10 2 2.481,4.999 2.587,5.156 0.106,0.156 10 1

A255771E05
0.5,1.177 1.646,1.594 1.146,0.417 10 false Throttle with Motor Body Assembly 0.521,2.771 1.625,3.188 1.104,0.417 10 false Accelerator Pedal Sensor Assembly 1.802,3.719 2.333,4.01 0.531,0.292 10 false VCPA 1.896,4.458 2.313,4.708 0.417,0.25 10 false VPA 1.896,4.104 2.281,4.333 0.385,0.229 10 false EPA 1.833,3.354 2.344,3.615 0.51,0.26 10 false VPA2 1.823,3 2.375,3.292 0.552,0.292 10 false EPA2 1.823,2.635 2.365,2.906 0.542,0.271 10 false VCP2 1.979,1.813 2.208,1.958 0.229,0.146 10 false VC 1.917,2.156 2.313,2.396 0.396,0.24 10 false VTA 1.833,1.438 2.208,1.594 0.375,0.156 10 false VTA2 2,1.083 2.208,1.229 0.208,0.146 10 false E2 2.281,2.917 2.531,3.219 0.25,0.302 10 false 2 2.271,0.969 2.604,1.281 0.333,0.313 10 false 3 2.281,3.281 2.542,3.542 0.26,0.26 10 false 3 2.271,1.323 2.5,1.604 0.229,0.281 10 false 4 2.281,3.646 2.479,3.896 0.198,0.25 10 false 4 2.271,1.698 2.49,1.969 0.219,0.271 10 false 5 2.281,4.01 2.448,4.292 0.167,0.281 10 false 5 2.271,2.063 2.438,2.313 0.167,0.25 10 false 6 2.281,4.375 2.427,4.646 0.146,0.271 10 false 6 2.281,2.563 2.49,2.833 0.208,0.271 10 false 1 4.99,0.885 5.24,1.042 0.25,0.156 10 false 125 5.031,3.208 5.24,3.365 0.208,0.156 10 false 57 5.031,2.458 5.24,2.615 0.208,0.156 10 false 59 5.031,3.927 5.24,4.083 0.208,0.156 10 false 55 5.031,3.563 5.24,3.719 0.208,0.156 10 false 56 5.031,2.844 5.292,3.063 0.26,0.219 10 false 58 5.031,4.292 5.229,4.458 0.198,0.167 10 false 54 4.99,1.25 5.24,1.406 0.25,0.156 10 false 127 4.99,1.979 5.25,2.135 0.26,0.156 10 false 128 4.979,1.063 5.292,1.219 0.313,0.156 10 false E26 4.99,1.417 5.271,1.573 0.281,0.156 10 false E26 4.99,2.146 5.333,2.302 0.344,0.156 10 false E26 4.979,2.646 5.271,2.802 0.292,0.156 10 false A25 4.99,3.01 5.292,3.167 0.302,0.156 10 false A25 4.979,3.375 5.271,3.531 0.292,0.156 10 false A25 4.979,3.74 5.25,3.896 0.271,0.156 10 false A25 4.979,4.104 5.271,4.26 0.292,0.156 10 false A25 4.979,4.469 5.271,4.625 0.292,0.156 10 false A25 5.802,5.177 6.292,5.427 0.49,0.25 10 false ECM 5.323,1.688 5.729,1.844 0.406,0.156 10 false VCTA 5.323,0.958 5.615,1.115 0.292,0.156 10 false ETA 4.99,1.615 5.26,1.771 0.271,0.156 10 false 126 4.99,1.781 5.313,1.938 0.323,0.156 10 false E26 5.323,2.146 5.729,2.302 0.406,0.156 10 false VTA1 5.323,3.635 5.792,3.844 0.469,0.208 10 false VCPA 5.323,4.479 5.635,4.635 0.313,0.156 10 false VPA 5.323,4.021 5.729,4.24 0.406,0.219 10 false EPA 5.323,3.375 5.708,3.531 0.385,0.156 10 false VPA2 5.323,2.917 5.708,3.073 0.385,0.156 10 false EPA2 5.323,2.563 5.729,2.719 0.406,0.156 10 false VCP2 5.323,1.417 5.698,1.573 0.375,0.156 10 false VTA2 0.51,2.615 0.969,2.875 0.458,0.26 10 false A36 0.51,1 0.885,1.271 0.375,0.271 10 false E16

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when the ignition switch is turned to ON.

OK:

MIL lights up.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM
2.CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Check the communication between the tester and ECM.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

3.CHECK MIL (THROTTLE POSITION SENSOR)

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle with motor body assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B


HINT:

Perform "Inspection After Repair" after replacing the throttle with motor body assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)

B

REPLACE THROTTLE W/MOTOR BODY ASSEMBLY

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

5.CHECK MIL (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1))

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK MIL (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1))
a.

Disconnect the VVT sensor (for intake camshaft of bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

6.CHECK MIL (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2))

B

REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1)

6.CHECK MIL (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2))
a.

Disconnect the VVT sensor (for intake camshaft of bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

7.CHECK MIL (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1))

B

REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2)

7.CHECK MIL (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1))
a.

Disconnect the VVT sensor (for exhaust camshaft of bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

8.CHECK MIL (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2))

B

REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1)

8.CHECK MIL (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2))
a.

Disconnect the VVT sensor (for exhaust camshaft of bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

9.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

B

REPLACE VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2)

9.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle with motor body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E16-5 (VC) or E26-126 (VCTA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-4 (VCPA) or A25-56 (VCPA) - Body ground Always 10 kΩ or higher
A36-1 (VCP2) or A25-59 (VCP2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (VCV1 CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (VCV1 CIRCUIT)
a.

Disconnect the VVT sensor (for intake camshaft of bank 1) connector.


b.

Disconnect the VVT sensor (for intake camshaft of bank 2) connector.


c.

Disconnect the VVT sensor (for exhaust camshaft of bank 1) connector.


d.

Disconnect the VVT sensor (for exhaust camshaft of bank 2) connector.


e.

Disconnect the ECM connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E26-111 (VCV1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR