Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2012.02–2013.07
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) One of the following conditions A, B or C is met (2 trip detection logic):
A. One of the following conditions (a), (b) or (c) is met for 2 seconds or more:
(a) Any 2 or more signals of the following are on simultaneously:
·

P input signal

·

R input signal

·

D input signal


(b) Any 2 or more signals of the following are on simultaneously:
·

N input signal

·

R input signal

·

D input signal


(c) Any 2 or more signals of the following are on simultaneously:
·

NSW input signal

·

R input signal

·

D input signal


B. Any of the following conditions is met for 2 seconds or more in the S position:
·

NSW input signal is on

·

P input signal is on

·

N input signal is on

·

R input signal is on


C. All switches are off simultaneously for NSW, P, R, N and D for 1 minute or more.
·

Open or short in park/neutral position switch assembly circuit

·

Short in park/neutral position switch assembly

·

Open or short in transmission control switch circuit

·

Lower shift lever assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends a signal to the ECM.

For security, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, R, N, D, or S). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY

Required Sensors/Components Park/Neutral position switch assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Move the shift lever to R and wait 2 seconds or more.

7.

Move the shift lever to N and wait 2 seconds or more.

8.

Move the shift lever to D and wait 2 seconds or more.

9.

Move the shift lever to S and wait 2 seconds or more.

10.

Move the shift lever to P and wait 2 seconds or more.

11.

Wait 1 minute or more.

12.

Enter the following menus: Powertrain / Engine / DTC.

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P0705.

16.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A270947E03
4.958,1.979 5.135,2.156 0.177,0.177 10 false 7 4.958,2.427 5.135,2.604 0.177,0.177 10 false 8 4.958,2.844 5.135,3.021 0.177,0.177 10 false 2 4.958,3.281 5.135,3.458 0.177,0.177 10 false 3 4.958,3.708 5.135,3.885 0.177,0.177 10 false 4 4.656,2.042 4.938,2.208 0.281,0.167 10 false DL 4.656,2.458 4.938,2.625 0.281,0.167 10 false NL 4.656,2.906 4.938,3.073 0.281,0.167 10 false RL 4.656,3.344 4.938,3.51 0.281,0.167 10 false PL 4.75,3.792 4.875,3.958 0.125,0.167 10 false B 5.688,1.896 5.865,2.073 0.177,0.177 10 false 69 5.688,2.323 5.865,2.5 0.177,0.177 10 false 71 5.677,2.771 5.854,2.948 0.177,0.177 10 false 68 5.698,3.208 5.875,3.385 0.177,0.177 10 false 70 5.688,3.635 5.938,3.813 0.25,0.177 10 false 65 5.656,2.073 5.938,2.24 0.281,0.167 10 false E26 5.646,2.51 5.927,2.677 0.281,0.167 10 false E26 5.656,2.938 5.938,3.104 0.281,0.167 10 false E26 5.646,3.375 5.927,3.542 0.281,0.167 10 false E26 5.656,3.813 5.938,3.979 0.281,0.167 10 false E26 5.99,2.063 6.135,2.229 0.146,0.167 10 false D 5.99,2.5 6.271,2.667 0.281,0.167 10 false N 5.979,2.938 6.104,3.104 0.125,0.167 10 false R 5.99,3.365 6.271,3.531 0.281,0.167 10 false P 6,3.823 6.375,3.99 0.375,0.167 10 false NSW 5.656,0.604 5.938,0.771 0.281,0.167 10 false A25 5.99,0.594 6.365,0.76 0.375,0.167 10 false S 5.688,0.438 5.865,0.615 0.177,0.177 10 false 37 0.281,0.594 1.135,0.927 0.854,0.333 10 false from Battery 5.656,4.698 5.938,4.865 0.281,0.167 10 false A25 6.01,4.698 6.385,4.865 0.375,0.167 10 false STA 5.708,4.521 5.885,4.698 0.177,0.177 10 false 9 2.219,4.698 3.146,4.958 0.927,0.26 10 false from ST Relay 3.49,3.083 4.219,3.229 0.729,0.146 10 false BKUP LP 2.531,1.552 3.219,1.75 0.688,0.198 10 false IG1 NO. 2 3.219,0.76 4.24,0.906 1.021,0.146 10 false ECU-IG1 NO. 1 5.031,0.5 5.229,0.667 0.198,0.167 10 false 5 4.083,0.5 4.198,0.667 0.115,0.167 10 false 4 4.26,0.719 4.427,0.875 0.167,0.156 10 false IG 4.833,0.719 4.948,0.865 0.115,0.146 10 false S 3.542,1.094 3.802,1.26 0.26,0.167 10 false I44 3.813,1.094 5.875,1.479 2.063,0.385 10 false Lower Shift Lever Assembly (Transmission Control Switch) 4.146,3.719 4.323,3.896 0.177,0.177 10 false 9 4.365,3.792 4.49,3.958 0.125,0.167 10 false L 4.125,2.854 4.302,3.031 0.177,0.177 10 false 1 4.354,2.948 4.573,3.115 0.219,0.167 10 false RB 6.24,5.344 6.615,5.51 0.375,0.167 10 false ECM 0.5,1.25 1.906,2.135 1.406,0.885 10 false from Ignition or Starter Switch Assembly*1 or Certification ECU (Smart Key ECU Assembly)*2 3.854,4.135 4.083,4.281 0.229,0.146 10 false E4 4.115,4.125 5.49,4.448 1.375,0.323 10 false Park/Neutral Position Switch Assembly 1.656,2.948 3.042,3.135 1.385,0.188 10 false from IG1 NO. 1 Relay 0.354,5.021 2.833,5.208 2.479,0.188 10 false *1: w/o Smart Entry and Start System 0.354,5.344 2.833,5.531 2.479,0.188 10 false *2: w/ Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may by discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Enter the following menus: Powertrain / Engine / Data List / All Data.


g.

Read the values displayed on the tester.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (P Range) Park/Neutral position switch assembly status: ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (R Range) Park/Neutral position switch assembly status: ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (N Range) Park/Neutral position switch assembly status: ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Sports Mode Selection SW Sport mode select switch status: ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Shift SW Status (D Range) Park/Neutral position switch assembly status: ON or OFF
·

ON: Shift lever in D or S

·

OFF: Shift lever not in D or S


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (NEUTRAL POSITION SW SIGNAL AND SHIFT SW STATUS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Neutral Position SW Signal and Shift SW Status (R, P, N and D Range).

Powertrain > Engine > Data List
Tester Display
Neutral Position SW Signal
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 234 147,125,126,127,128

e.

Read the values displayed on the tester.

OK:
Tester Display Shift Lever Position Specified Condition
Neutral Position SW Signal P or N ON
Except P or N OFF
Shift SW Status (R Range) R ON
Except R OFF
Shift SW Status (P Range) P ON
Except P OFF
Shift SW Status (N Range) N ON
Except N OFF
Shift SW Status (D Range) D or S ON
Except D or S OFF



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (SPORTS MODE SELECTION SW)

NG

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
2.READ VALUE USING INTELLIGENT TESTER (SPORTS MODE SELECTION SW)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Sports Mode Selection SW.

Powertrain > Engine > Data List
Tester Display
Sports Mode Selection SW
50003 234 133

e.

Read the values displayed on the tester.

OK:
Tester Display Shift Lever Position Specified Condition
Sports Mode Selection SW S ON
Except S OFF



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH)
3.INSPECT LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.

Inspect the transmission control switch.

Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>SHIFT LEVER>REMOVAL


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - TRANSMISSION CONTROL SWITCH)

NG

REPLACE LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH)

4.CHECK HARNESS AND CONNECTOR (ECM - TRANSMISSION CONTROL SWITCH)
a.
A255690C47
0.49,1.052 0.979,1.344 0.49,0.292 1.875,1.385 1.771,1.917 false 0.177,0.146 0.542,0.635 0.365,0.49 10 false *a 0.625,1.104 1.135,1.469 0.51,0.365 10 false A25 1.698,1.917 1.969,2.177 0.271,0.26 10 false S
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Shift Lever Position Condition Specified Condition
A25-37 (S) - Body ground S, "+" or "-" Ignition switch ON 11 to 14 V
Not in S Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.
A194118C05
0.26,2.26 0.698,2.521 0.438,0.26 1.583,2.375 1.167,1.417 1.167,1.417 1,1.417 false 0.188,0.167 0.677,0.583 0.49,0.417 10 false *a 0.417,2.313 0.844,2.531 0.427,0.219 10 false E4 0.708,1.365 1.031,1.635 0.323,0.271 10 false RB
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E4-1 (RB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E4-7 (DL) - E26-69 (D) Always Below 1 Ω
E4-8 (NL) - E26-71 (N) Always Below 1 Ω
E4-2 (RL) - E26-68 (R) Always Below 1 Ω
E4-3 (PL) - E26-70 (P) Always Below 1 Ω
E4-4 (B) - E26-65 (NSW) Always Below 1 Ω
E4-7 (DL) or E26-69 (D) - Body ground Always 10 kΩ or higher
E4-8 (NL) or E26-71 (N) - Body ground Always 10 kΩ or higher
E4-2 (RL) or E26-68 (R) - Body ground Always 10 kΩ or higher
E4-3 (PL) or E26-70 (P) - Body ground Always 10 kΩ or higher
E4-4 (B) or E26-65 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR