Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P2121  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  


DESCRIPTION

HINT:
·

This DTC relates to the accelerator pedal position sensor.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance Either of following conditions 1 or 2 met for 0.5 seconds (1 trip detection logic):

1. Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V. (learned value of accelerator off position)

2. Difference between VPA and VPA2 is greater than or equal to the specified value.


·

Accelerator pedal sensor assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The accelerator pedal position sensor is mounted on the accelerator pedal bracket. The accelerator pedal position sensor has 2 sensor elements and 2 signal outputs: VPA and VPA2. VPA is used to detect the actual accelerator pedal angle (used for engine control) and VPA2 is used to detect malfunctions in VPA. When the difference between the output voltages of VPA and VPA2 deviates from the standard, the ECM determines that the accelerator pedal position sensor is malfunctioning. The ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY

Required Sensors/Components Accelerator pedal sensor assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A256657E01
3.635,2.01 2.771,1.302 2.771,1.302 2.927,1.302 false 4.729,2.448 5.115,1.802 5.115,1.802 5.26,1.802 false 2.208,2.448 2.438,2.104 2.438,2.104 2.542,2.104 false 0.125,0.094 1.75,0.333 1.625,0.24 10 Accelerator Pedal State 0.896,0.458 1.698,0.708 0.802,0.25 10 Depressed 0.99,0.927 1.708,1.167 0.719,0.24 10 Released 0.427,2.406 1.667,2.667 1.24,0.26 10 Ignition Switch ON 2.115,2.49 2.333,2.75 0.219,0.26 10 [A] 4.396,3.406 4.646,3.635 0.25,0.229 10 [C] 5.313,1.729 6.063,1.979 0.75,0.25 10 Released 2.375,3.052 3.167,3.333 0.792,0.281 10 5 seconds 2.99,1.219 3.823,1.469 0.833,0.25 10 Depressed 3.865,3.042 4.083,3.25 0.219,0.208 10 [B] 2.594,2.031 3.25,2.25 0.656,0.219 10 Released

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Wait for 5 seconds after turning the ignition switch to ON.

7.

Operate the accelerator pedal in accordance with the following procedure [B].

1.

Enter the following menus: Powertrain / Engine / Data List / All Data / Accel Sens. No. 1 Volt %, and Accel Sens. No. 2 Volt %.

2.

Slowly depress the accelerator pedal until Accel Sens. No. 1 Volt % is approximately 30% and Accel Sens. No. 2 Volt % is approximately 46%, then slowly release the accelerator pedal.


8.

Enter the following menus: Powertrain / Engine / DTC [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P2121.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.




FAIL-SAFE

The accelerator pedal position sensor has 2 (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the 2 sensor circuits and switches to fail-safe mode. In fail-safe mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling.

If a pass condition is detected and then the ignition switch is turned off, the fail-safe operation stops and the system returns to normal.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2121)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P2121 is output A
DTC P2121 and other DTCs are output B


HINT:

If any DTCs other than P2121 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (ACCEL SENSOR OUT)

B

2.READ VALUE USING INTELLIGENT TESTER (ACCEL SENSOR OUT)
a.
A208621C06
0.667,1.75 1.448,2.177 0.781,0.427 10 *a 2.615,1.75 3.177,2.177 0.563,0.427 10 *b
*1 Fully Depressed
*2 Fully Released


Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

Powertrain > Engine > Data List
Tester Display
Accel Sensor Out No.1
Accel Sensor Out No.2
50003 234 280,281

e.

Read the values displayed on the tester.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No. 1 Accel Sensor Out No. 2
Fully Released 0.5 to 1.1 V 1.2 to 2.0 V
Fully Depressed 2.6 to 4.5 V 3.4 to 4.98 V



Result:
Proceed to
OK
NG



OK

NG

3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the tester on.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine / DTC.


i.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P2121 is output A
DTC is not output B




A

B

END