Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › AIR FUEL RATIO SENSOR
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074406 AIR FUEL RATIO SENSOR A

2GR-FE ENGINE CONTROL  AIR FUEL RATIO SENSOR  INSTALLATION  


PROCEDURE

Hide 89467B 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

a.
A255016C01
2.531,0.844 2.313,1.708 2.313,1.708 1.813,1.354 false 2.74,0.948 2.99,1.125 0.25,0.177 10 *a 1.688,0.344 1.865,0.51 0.177,0.167 10 *b 2.198,1.74 2.49,2.073 0.292,0.333 10 SST
*a Fulcrum Length
30 mm (1.18 in.)
*b Fulcrum Length
180 mm (7.09 in.)


Using SST, install the air fuel ratio sensor to the exhaust manifold RH.

SST
09224-00010  

Torque:
without SST : 44 N*m (449 kgf*cm, 33 ft.*lbf)
with SST : 40 N*m (408 kgf*cm, 30 ft.*lbf)

NOTICE:
·

The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.) and a torque wrench with a fulcrum length of 180 mm (7.09 in.).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The "with SST" torque value is effective when SST is parallel to the torque wrench.



HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



b.

Connect the harness clamp.


c.

Connect the air fuel ratio sensor connector.


Hide 2.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 89467B 3.INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

a.
A292403C01
1.115,1.51 1.542,1.74 1.542,1.74 1.802,1.438 false 0.667,1.833 0.979,1.99 0.313,0.156 10 *a 2.083,0.344 2.396,0.5 0.313,0.156 10 *b 1.417,1.76 1.771,2.01 0.354,0.25 10 SST
*a Fulcrum Length
30 mm (1.18 in.)
*b Fulcrum Length
180 mm (7.09 in.)


Using SST, install the air fuel ratio sensor to the exhaust manifold LH.

SST
09224-00010  

Torque:
without SST : 44 N*m (449 kgf*cm, 33 ft.*lbf)
with SST : 40 N*m (408 kgf*cm, 30 ft.*lbf)

NOTICE:
·

The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.) and a torque wrench with a fulcrum length of 180 mm (7.09 in.).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The "with SST" torque value is effective when SST is parallel to the torque wrench.



HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



b.

Connect the air fuel ratio sensor connector.


c.

Install the wire harness clamp.


Hide 4.INSPECT FOR EXHAUST GAS LEAK

Hide 53295E 6.INSTALL COOL AIR INTAKE DUCT SEAL