Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY
RM2030EQ _51 Engine / Hybrid System _014635 2GR-FE ENGINE MECHANICAL _0074416 ENGINE ASSEMBLY A

2GR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.REMOVE ENGINE STAND

Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 43457 3.INSTALL DRIVE SHAFT BEARING BRACKET

a.

Install the drive shaft bearing bracket with the 3 bolts.

Torque:
64 N*m (650 kgf*cm, 47 ft.*lbf)


Hide 12315A 4.INSTALL ENGINE MOUNTING BRACKET RH

a.

Install the engine mounting bracket RH with the 3 bolts.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


Hide 82121 6.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine with transaxle.


Hide 12360 7.INSTALL FRONT ENGINE MOUNTING INSULATOR ASSEMBLY

a.

Temporarily install the front engine mounting insulator assembly with the 3 nuts.

HINT:

Perform this procedure only when replacement of the front engine mounting insulator assembly is necessary.



Hide 12372A 8.INSTALL ENGINE MOUNTING INSULATOR LH

a.

Temporarily install the engine mounting insulator LH with the 3 nuts.

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.



Hide 12362 9.INSTALL ENGINE MOUNTING INSULATOR RH

a.

Temporarily install the engine mounting insulator RH with the 3 nuts.

HINT:

Perform this procedure only when replacement of the engine mounting insulator RH is necessary.



Hide 51100G 10.INSTALL FRONT FRAME ASSEMBLY

a.

Install the engine mounting insulator RH with the nut.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


b.

Install the engine mounting insulator LH with the nut.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


c.

Install the front engine mounting insulator assembly with the bolt.

Torque:
87 N*m (888 kgf*cm, 65 ft.*lbf)


d.

Connect the 2 wire clamps and vacuum switching valve connector.


e.

Connect the 2 wire clamps.


f.

Fully tighten the 9 temporarily installed nuts of the engine mounting insulators to the specified torque.

HINT:

Perform this procedure only when replacement of the engine mounting insulator is necessary.


A172973C09
0.208,0.229 0.49,0.417 0.281,0.188 10 *1 2.198,0.229 2.479,0.417 0.281,0.188 10 *2 4.646,0.229 4.927,0.417 0.281,0.188 10 *3 0.177,1.938 0.313,2.104 0.135,0.167 10 A 0.792,1.469 0.927,1.635 0.135,0.167 10 A 1.458,1.896 1.594,2.063 0.135,0.167 10 A 3.021,0.958 3.156,1.125 0.135,0.167 10 B 3.469,1.365 3.604,1.531 0.135,0.167 10 B 3.865,0.646 4,0.813 0.135,0.167 10 B 5.438,1.135 5.573,1.302 0.135,0.167 10 B 6.01,1.094 6.146,1.26 0.135,0.167 10 B 6.219,1.979 6.354,2.146 0.135,0.167 10 B
*1 Front Engine Mounting Insulator Assembly *2 Engine Mounting Insulator RH
*3 Engine Mounting Insulator LH - -


Torque:
A : 52 N*m (530 kgf*cm, 38 ft.*lbf)

Torque:
B : 87 N*m (887 kgf*cm, 64 ft.*lbf)


g.

Install the 4 hole plugs.

HINT:

Perform this procedure only when replacement of the engine mounting insulator is necessary.


A256545C09
0.707,0.06 0.975,0.291 0.267,0.23 10 *1 4.112,0.06 4.379,0.291 0.267,0.23 10 *2
*1 Engine Mounting Insulator RH *2 Engine Mounting Insulator LH



Hide 88310 11.INSTALL COMPRESSOR AND MAGNETIC CLUTCH

Hide 27020 12.INSTALL GENERATOR ASSEMBLY

Hide 14.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Install a height adjustment attachment and plate lift attachment onto the engine assembly with transaxle.

·

Do not position a height adjustment attachment or plate lift attachment onto the front frame assembly.

·

Servicing an engine assembly while it is hanging is dangerous. This can be done only when installing/removing the engine assembly to/from an engine stand.

·

To prevent the oil pan from deforming, do not place any attachments onto the oil pan of the engine assembly with transaxle.

·

Make sure to support the engine assembly with transaxle securely to prevent it from falling.





c.

Install the engine assembly with transaxle to the vehicle.

NOTICE:
·

Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.

·

Make sure that the engine is clear of all wiring and hoses.

·

While raising the engine into the vehicle, do not allow it to contact the vehicle.




d.
A255441N01
0.198,1.24 0.313,1.385 0.115,0.146 10 false A 3.083,1.26 3.198,1.406 0.115,0.146 10 false A 1.083,0.208 1.198,0.354 0.115,0.146 10 false B 0.115,0.052 0.229,0.198 0.115,0.146 10 false B 2.292,0.229 2.406,0.375 0.115,0.146 10 false B 3.281,0.031 3.396,0.177 0.115,0.146 10 false B 1.177,2.677 1.302,2.823 0.125,0.146 10 false C 2.177,2.646 2.302,2.792 0.125,0.146 10 true C 0.271,2.292 0.396,2.438 0.125,0.146 10 false D 0.979,3.073 1.104,3.219 0.125,0.146 10 false D 2.354,3.021 2.479,3.167 0.125,0.146 10 false D 3.021,2.323 3.146,2.469 0.125,0.146 10 false D

Install the frame side rail plates RH and LH with the 4 bolts and 2 nuts.

Torque:
A : 85 N*m (867 kgf*cm, 62 ft.*lbf)
B : 32 N*m (329 kgf*cm, 24 ft.*lbf)


e.

Install the front suspension member rear braces RH and LH with the 4 bolts and 2 nuts.

Torque:
C : 85 N*m (867 kgf*cm, 62 ft.*lbf)
D : 32 N*m (329 kgf*cm, 24 ft.*lbf)

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 32101A 15.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
P000601C18
1.979,1.208 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 false *1
*1 Adhesive 1324


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.



b.

Turn the crankshaft to gain access to the installation locations of the 6 torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

First install the black colored bolt, and then the remaining 5 silver colored bolts.



Hide 17506A 16.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY

a.

Install the No. 1 exhaust pipe support bracket sub-assembly with the 2 bolts.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


Hide 17571 17.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET

a.

Install the No. 1 exhaust pipe support bracket with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 43420G 18.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH

Hide 43420 19.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 20.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

Hide 48069 21.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 22.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45470 23.CONNECT TIE ROD ASSEMBLY LH

Hide 45460 24.CONNECT TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 89543 25.INSTALL FRONT SPEED SENSOR LH

Hide 89542 26.INSTALL FRONT SPEED SENSOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 27.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 28.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 43502H 29.INSTALL FRONT AXLE SHAFT NUT LH

Hide 43501H 30.INSTALL FRONT AXLE SHAFT NUT RH

HINT:

Perform the same procedure as for the LH side.


Hide 45220 31.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 17410 32.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 17584B 33.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET

Hide 88704 34.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88711 35.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 23901 36.CONNECT FUEL TUBE SUB-ASSEMBLY

a.
A088337

Push in the fuel tube connector to the fuel main tube until the fuel tube connector makes a "click" sound.

NOTICE:
·

Check that there is no damage or foreign objects on the fuel tube connector.

·

After connecting, check that the fuel tube connector and the tube are securely connected by pulling on them.




b.
A255435

Install the fuel pipe clamp.

HINT:

The half connection prevention connector prevents the fuel hose connector cover from being locked if the fuel tube is not securely connected.



Hide 33820B 37.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 17771A 38.INSTALL AIR CLEANER BRACKET

a.

Install the air cleaner bracket to the battery carrier with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Connect the 2 wire clamps.


Hide 82121 39.CONNECT ENGINE WIRE

a.
A255463

Connect the 2 wire clamps.


b.

Connect the connector to the ECM with the lock lever.


c.

Connect the engine wire to the engine room relay block.


d.

Connect the 4 connectors.


e.
A255437

Connect the engine wire to the engine room relay block.


f.

Connect the wire clamp and install the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.

Install the No. 1 relay block cover.


Hide 28100 40.INSTALL STARTER ASSEMBLY

Hide 87246 41.CONNECT OUTLET HEATER WATER HOSE

a.

Connect the outlet heater water hose with the hose clip.


Hide 87245 42.CONNECT INLET HEATER WATER HOSE

a.

Connect the inlet heater water hose with the hose clip.


Hide 32941 43.CONNECT INLET NO. 1 OIL COOLER HOSE

a.

Connect the inlet No. 1 oil cooler hose to the automatic transaxle assembly with the hose clip.


Hide 32942 44.CONNECT OUTLET NO. 1 OIL COOLER HOSE

a.

Connect the outlet No. 1 oil cooler hose to the automatic transaxle assembly with the hose clip.


Hide 16572D 45.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose with the hose clip.


Hide 16571C 46.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose with the hose clip.


b.

Install the air fuel ratio sensor wire to the No. 1 radiator hose with the hose clamp.


Hide 44773F 47.CONNECT UNION TO CHECK VALVE HOSE (for LHD)

a.

Connect the union to check valve hose to the brake booster with the hose clip.


Hide 44772B 48.CONNECT CHECK VALVE TO BRAKE BOOSTER HOSE (for RHD)

a.

Connect the check valve to brake booster hose to the brake booster with the hose clip.


Hide 23826 49.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose with the hose clip.


Hide 82284 50.CONNECT EARTH WIRE

a.

Install the earth wire with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 12309 51.INSTALL ENGINE MOVING CONTROL ROD SUB-ASSEMBLY

a.
A268428N03
0.896,0.125 1.052,0.323 0.156,0.198 10 false A 2.448,1.74 2.604,1.938 0.156,0.198 10 false B 1.979,0.396 2.135,0.594 0.156,0.198 10 false C 2.396,1.302 2.552,1.5 0.156,0.198 10 false D

Install the engine moving control rod bracket with engine moving control rod with the 4 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)

NOTICE:

Temporarily tighten bolt A and B, and then fully tighten the 4 bolts in the order of C, D, A and B.



Hide 12327A 52.INSTALL NO. 2 ENGINE MOUNTING STAY RH

a.

Install the No. 2 engine mounting stay RH with the bolt.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


b.

Tighten the 2 nuts.

Torque:
23 N*m (234 kgf*cm, 17 ft.*lbf)


Hide 17805F 53.INSTALL INTAKE AIR RESONATOR SUB-ASSEMBLY

a.

Install the intake air resonator sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Connect the 2 vacuum hoses and engage the claw.


Hide 17751 54.INSTALL INLET NO. 1 AIR CLEANER

a.
A256227

Install the inlet No. 1 air cleaner to the intake air resonator sub-assembly.


b.

Engage the pin to the radiator support.


Hide 55.INSTALL BATTERY

a.

Install the battery and battery tray.


b.

Install the battery clamp with the bolt and nut.

Torque:
Bolt : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
Nut : 3.5 N*m (36 kgf*cm, 31 in.*lbf)


c.

Connect the positive (+) cable to the positive (+) battery terminal.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 56.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.
A255422C03
2.625,3 2.229,3 2.229,3 2.188,2.854 false 2.542,3.281 2.146,3.281 2.146,3.281 2.094,3.229 false 2.719,0.552 2.885,0.552 false 2.698,0.781 2.865,0.781 false 2.563,0.448 2.875,0.646 0.313,0.198 10 false *a 2.542,0.719 2.854,0.917 0.313,0.198 10 false *b 2.667,2.948 2.979,3.146 0.313,0.198 10 false *1 2.573,3.198 2.885,3.396 0.313,0.198 10 false *2
*1 Air Cleaner Case Sub-assembly
*2 Inlet No. 1 Air Cleaner
*a Projection
*b Hole


Install the air cleaner case sub-assembly to the inlet No. 1 air cleaner.


b.

Insert the projection of the air cleaner case sub-assembly to the hole of the No. 2 air cleaner bracket as shown in the illustration.


c.

Tighten the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the wire harness clamp, connector, vacuum hose and No. 1 fuel vapor feed hose.


Hide 17801 57.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.

NOTICE:

Install the air cleaner filter element sub-assembly with the printed side facing the vehicle front.



Hide 58.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 17752 59.INSTALL INLET NO. 2 AIR CLEANER

a.

Install the inlet No. 2 air cleaner to the air cleaner case sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Connect the 2 wire harness clamps and vacuum hose clamp.


Hide 60.INSPECT VACUUM HOSES

a.

Inspect the vacuum hoses.

A276511


Hide 61.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

a.

Connect the negative (-) cable to the negative (-) battery terminal.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 62.INSTALL FRONT WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 66.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 70.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR

Hide 73.INSPECT FOR OIL LEAK

Hide 74.INSPECT FOR EXHAUST GAS LEAK

Hide 81.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 11209 82.INSTALL V-BANK COVER SUB-ASSEMBLY

a.

Fit the 3 retainers and install the V-bank cover sub-assembly.


Hide 53295E 83.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 53737B 84.INSTALL FRONT FENDER APRON SEAL LH

Hide 51442C 85.INSTALL ENGINE UNDER COVER LH

Hide 53852K 86.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH (for RHD)

Hide 53736 87.INSTALL FRONT FENDER APRON SEAL RH

Hide 53851Z 88.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)

Hide 51441C 89.INSTALL ENGINE UNDER COVER RH