Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › ENGINE UNIT
RM2030EQ _51 Engine / Hybrid System _014635 2GR-FE ENGINE MECHANICAL _0074417 ENGINE UNIT G

2GR-FE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13801 1.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A125485

Turn the roller by hand to check that it turns smoothly.

HINT:

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.



Hide 13750 2.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the valve lash adjuster assembly free of dirt and foreign objects.

·

Only use clean engine oil.



a.

Place the valve lash adjuster assembly into a container filled with engine oil.


b.

Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.

A284094
4.625,0.958 5.052,1.344 true 2.313,1.979 3,1.979 true 1.344,1.979 2.021,1.979 true 2.313,2.344 2.844,2.125 true 1.5,2.115 2.042,2.354 true 2.323,1.594 2.896,1.594 true 1.448,1.594 2.01,1.594 true 2.313,1.208 2.844,1.208 false 1.51,1.208 2.021,1.208 false 2.406,0.521 2.781,0.521 false 1.583,0.521 2.01,0.521 false 2.865,0.875 2.313,0.875 true 1.458,0.948 2.031,0.875 true 2.042,0.427 2.5,0.625 0.458,0.198 10 SST 4.344,0.823 4.802,1.021 0.458,0.198 10 SST 2.115,2.292 2.385,2.542 0.271,0.25 10 *d 2.104,1.125 2.375,1.375 0.271,0.25 10 *2 2.104,0.781 2.375,1.031 0.271,0.25 10 *1 2.115,1.49 2.385,1.74 0.271,0.25 10 *c 3.01,0.083 3.281,0.333 0.271,0.25 10 *b 1.24,0.083 1.51,0.333 0.271,0.25 10 *a 2.115,1.885 2.385,2.135 0.271,0.25 10 *3
*1 Tapered Part *2 Plunger
*3 Check Ball - -
*a CORRECT *b INCORRECT
*c Low Pressure Chamber *d High Pressure Chamber


SST
09276-75010  


c.

Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed the air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding air from the high-pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger by hand.

OK:

Plunger is very difficult to move.


If the result is not as specified, replace the valve lash adjuster assembly.


Hide 13511 3.INSPECT CAMSHAFT

a.

Inspect the camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.
A120669

Using a dial indicator, measure the circle runout at the center journal.

Maximum runout:

0.04 mm (0.00157 in.)


If the runout is greater than the maximum, replace the camshaft.

HINT:

Check the oil clearance after replacing the camshaft.




b.
A109632

Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:
Item Specification
Intake camshaft 44.316 to 44.416 mm (1.7448 to 1.7486 in.)
Exhaust camshaft 44.262 to 44.362 mm (1.7426 to 1.7465 in.)


Minimum Cam Lobe Height:
Item Specification
Intake camshaft 44.166 mm (1.7388 in.)
Exhaust camshaft 44.112 mm (1.7366 in.)


If the cam lobe height is less than the minimum, replace the camshaft.


c.
A109633

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specification
No. 1 journal 35.946 to 35.960 mm (1.4152 to 1.4157 in.)
Other journals 25.959 to 25.975 mm (1.0221 to 1.0226 in.)


If the journal diameter is not as specified, check the oil clearance.


Hide 13050 4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.

Clamp the camshaft in a vise.

NOTICE:

Be careful not to damage the camshaft in the vise.



b.
A109635
0.844,0.031 1.01,0.208 0.167,0.177 10 *1 0.427,1.635 0.74,1.833 0.313,0.198 10 *a
*1 Straight Pin
*a Key Groove


Put the camshaft timing gear assembly and camshaft together by aligning the key groove and straight pin.


c.

Check that there is no clearance between the camshaft timing gear assembly flange and the camshaft.


d.
A109634

Tighten the flange bolt while holding the camshaft.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


e.

Check the lock of the camshaft timing gear assembly.

i.

Clamp the camshaft in a vise, and confirm that the camshaft timing gear assembly is locked.

NOTICE:

Be careful not to damage the camshaft.




f.
A106100
1.625,1 2.24,1 false 2.24,1 1.833,1.063 false 1.833,0.917 1.115,0.917 false 1.115,0.917 1.573,0.948 false 2.104,2.781 2.542,2.823 false 2.094,3.281 2.594,3.49 false 1.979,3.333 2.375,4.313 false 1.313,3.146 0.708,3.531 false 1.323,2.896 0.771,2.854 false 1.208,3.708 0.938,4.313 false 2.302,4.323 3.052,4.521 0.75,0.198 10 false *4 2.271,0.875 3.094,1.281 0.823,0.406 10 false *2 0.813,4.323 1.469,4.531 0.656,0.208 10 false *3 0.875,0.802 1.271,1.25 0.396,0.448 10 false *1 2.635,3.385 3.208,3.594 0.573,0.208 10 false *a 0.5,2.698 0.896,2.906 0.396,0.208 10 false *a 0.5,3.385 0.896,3.604 0.396,0.219 10 false *b 2.604,2.698 3.177,2.917 0.573,0.219 10 false *b
*1 Advance Side Path
*2 Retard Side Path
*3 Vinyl Tape
*4 Rubber
*a Close
*b Open


Release the lock pin.

i.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

The 2 advance side paths are located in the camshaft groove. Plug one of the paths with a rubber piece.



ii.

Break through the tape on the advance side path and the retard side path on the opposite side of the hole of the advance side path as shown in the illustration.


iii.
A106101
2.292,0.323 2.463,0.507 0.171,0.184 10 *2 1.013,0.082 1.18,0.269 0.167,0.188 10 *1 1.584,0.953 1.211,0.191 false 2.266,0.438 1.842,1.048 false
*1 Advanced Side Path
*2 Retard Side Path


Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the 2 opened paths.

CAUTION:

Cover the paths with a piece of cloth when applying pressure to prevent oil from spraying.



iv.
A106102
0.771,0.5 1.01,0.5 1.01,0.5 1.542,1.01 true 2.615,0.479 2.344,0.479 2.344,0.479 1.875,1.125 true 2.667,0.396 2.927,0.656 0.26,0.26 10 false *2 0.542,0.427 0.844,0.688 0.302,0.26 10 false *1 2.458,1.573 2.771,1.792 0.313,0.219 10 false *b 0.802,1.542 1.115,1.792 0.313,0.25 10 false *a
*1 Advance Side Path
*2 Retard Side Path
*a Hold Pressure
*b Decompress


Check that the camshaft timing gear assembly rotates in the advance direction when reducing the air pressure applied to the retard side path.

HINT:

This operation releases the lock pin at the most retarded position.



v.

When the camshaft timing gear assembly reaches the most advanced position, release the air pressure first from the retard side path and next from the advance side path.

NOTICE:

Do not release the air pressure from the advance side path first. The gear may abruptly shift in the retard direction and break the lock pin.




g.

Check for smooth rotation.

i.

Turn the camshaft timing gear assembly within its movable range (21°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.

NOTICE:

Do not use air pressure to perform the smooth operation check.




h.

Check the lock in the most retarded position.

i.

Confirm that the camshaft timing gear assembly locks at the most retarded position.



i.
A293115
1.865,0.948 2.094,0.438 2.094,0.438 2.271,0.438 false 1.021,2.01 0.656,2.01 0.656,2.01 0.354,1.552 false 1.177,1.542 2.063,1.635 2.063,1.635 1.323,1.229 false 0.927,1.031 0.469,0.604 false 2.333,0.344 2.646,0.542 0.313,0.198 10 *1 1.063,1.927 1.375,2.125 0.313,0.198 10 *2 2.125,1.615 2.438,1.813 0.313,0.198 10 *a 0.281,0.51 0.594,0.708 0.313,0.198 10 *a
*1 Straight Pin
*2 Flange Bolt
*a Do Not Remove


Remove the flange bolt and camshaft timing gear assembly.

NOTICE:
·

Do not remove the other 3 bolts.

·

If planning to reuse the camshaft timing gear, be sure to release the straight pin lock before installing the camshaft timing gear.




Hide 13080 5.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Clamp the camshaft in a vise.

NOTICE:

Be careful not to damage the camshaft in the vise.



b.
A109635
0.844,0.031 1.01,0.208 0.167,0.177 10 *1 0.427,1.635 0.74,1.833 0.313,0.198 10 *a
*1 Straight Pin
*a Key Groove


Put the camshaft timing exhaust gear assembly and camshaft together by aligning the key groove and straight pin.


c.

Check that there is no clearance between the gear flange and the camshaft.


d.
A107564

Tighten the flange bolt while holding the camshaft.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


e.

Check the camshaft timing exhaust gear lock.

i.

Make sure that the camshaft timing exhaust gear assembly locks.



f.
A106103
1.281,2.76 0.708,2.792 true 1.24,3.281 0.698,3.573 true 2.052,3.094 2.667,3.427 true 2.135,2.917 2.656,2.896 true 1.833,0.979 2.479,1.052 2.479,1.052 1.646,1.115 true 1.604,0.969 1,0.813 1,0.813 1.813,0.927 true 1.896,3.094 1.094,4.427 1.094,4.427 1.354,3.427 true 1.938,3.76 2.24,4.469 true 2.531,0.99 2.823,1.25 0.292,0.26 10 false *2 0.802,0.74 1.156,0.979 0.354,0.24 10 false *1 2.74,2.802 2.99,3.01 0.25,0.208 10 false *b 0.49,3.479 0.688,3.688 0.198,0.208 10 false *b 0.51,2.688 0.719,2.906 0.208,0.219 10 false *a 2.719,3.354 2.969,3.573 0.25,0.219 10 false *a 0.958,4.469 1.271,4.667 0.313,0.198 10 false *3 2.281,4.469 2.594,4.667 0.313,0.198 10 false *4
*1 Retard Side Path
*2 Advance Side Path
*3 Rubber
*4 Vinyl Tape
*a Open
*b Close


Release the lock pin.

i.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

The 2 advance side paths are located in the camshaft groove. Plug one of the paths with a rubber piece.



ii.

Break through the tape on the advance side path and the retard side path on the opposite side of the hole of the advance side path as shown in the illustration.


iii.
A106104
0.969,0.323 1.583,1.031 false 2.375,0.313 1.875,0.938 false 0.76,0.219 0.927,0.406 0.167,0.188 10 false *1 2.396,0.198 2.563,0.385 0.167,0.188 10 false *2
*1 Advanced Side Path
*2 Retard Side Path


Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the 2 opened paths (the advance side path and the retard side path).

CAUTION:

Cover the paths with a piece of cloth when applying pressure to prevent oil from spraying.



iv.
A106105
0.719,0.583 0.875,0.583 0.875,0.583 1.573,1.135 true 2.646,0.688 2.521,0.688 2.521,0.688 1.906,1.021 false 0.51,0.5 0.781,0.688 0.271,0.188 10 false *1 2.417,1.49 2.698,1.677 0.281,0.188 10 false *b 2.729,0.594 3,0.781 0.271,0.188 10 false *2 0.896,1.594 1.24,1.875 0.344,0.281 10 false *a
*1 Advance Side Path
*2 Retard Side Path
*a Decompress
*b Hold Pressure


Make sure that the camshaft timing exhaust gear assembly rotates in the retard direction when reducing the air pressure applied to the advance side path.

HINT:

The lock pin is released and the camshaft timing exhaust gear assembly turns in the retard direction.



v.

When the camshaft timing exhaust gear assembly moves to the most retarded position, release the air pressure first from the advance side path, and then release the air pressure from the retard side path.

NOTICE:

Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing exhaust gear assembly may abruptly shift in the advance direction and break the lock pin or other parts.




g.

Check for smooth rotation.

i.

Turn the camshaft timing exhaust gear assembly within its movable range (18.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear assembly turns smoothly.

NOTICE:

When the air pressure is released from the advance side path and then from the retard side path, the gear assembly automatically returns to the most advanced position due to the advance assist spring operation and locks. Gradually release the air pressure from the retard side path before performing the smooth rotation check.




h.

Check the lock at the most advanced position.

i.

Make sure that the camshaft timing exhaust gear assembly locks at the most advanced position.



i.
A293116
1.833,1.042 2,0.646 false 0.875,1.875 0.469,1.635 false 0.385,0.583 0.74,0.844 0.354,0.26 10 *a 2.021,1.635 2.375,1.896 0.354,0.26 10 *a 1.948,0.448 2.302,0.708 0.354,0.26 10 *1 0.938,1.823 1.292,2.083 0.354,0.26 10 *2
*1 Straight Pin
*2 Flange Bolt
*a Do Not Remove


Remove the flange bolt and camshaft timing exhaust gear assembly.

NOTICE:
·

Be sure not to remove the other 4 bolts.

·

If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.




Hide 11101A 6.INSPECT CYLINDER HEAD SET BOLT

a.
A192409
1.158,1.449 1.717,1.624 0.559,0.175 10 103 mm 2.109,0.331 2.269,0.493 0.16,0.162 10 *a
*a Measurement Point


Using a vernier caliper, measure the diameter of the threads at the measurement point.

Standard diameter:

10.85 to 11.00 mm (0.4272 to 0.4330 in.)


Minimum diameter:

10.70 mm (0.4212 in.)


Measurement point (distance from the seat):

103 mm (4.06 in.)


HINT:
·

If the diameter is less than the minimum, replace the cylinder head bolt. Failure to do so may lead to engine damage.


·

If there is any thread deformation, replace the cylinder head bolt with a new one.




Hide 13506 7.INSPECT CHAIN SUB-ASSEMBLY

a.
A168044
2.684,0.0 3.115,0.169 0.431,0.169 10 147 N 1.759,1.074 1.93,1.231 0.171,0.158 10 *a 0.651,1.746 0.784,1.924 0.133,0.178 10 0 0.823,1.752 0.937,1.902 0.113,0.15 10 1 1.004,1.75 1.124,1.919 0.12,0.169 10 2 1.187,1.751 1.305,1.909 0.118,0.159 10 3 1.364,1.748 1.491,1.894 0.127,0.146 10 4 1.553,1.752 1.671,1.899 0.118,0.147 10 5 2.935,1.739 3.12,1.897 0.185,0.158 10 15
*a Measuring Point


Pull the chain sub-assembly with a force of 147 N (15 kgf, 33.1 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 links.

Maximum chain elongation:

136.9 mm (5.389 in.)


NOTICE:

Perform the measurement at 3 random places. Use the average of the measurements.


If the average elongation is greater than the maximum, replace the chain sub-assembly.


Hide 13507 8.INSPECT NO. 2 CHAIN SUB-ASSEMBLY

a.
A168044
2.684,0.0 3.115,0.169 0.431,0.169 10 147 N 1.759,1.074 1.93,1.231 0.171,0.158 10 *a 0.651,1.746 0.784,1.924 0.133,0.178 10 0 0.823,1.752 0.937,1.902 0.113,0.15 10 1 1.004,1.75 1.124,1.919 0.12,0.169 10 2 1.187,1.751 1.305,1.909 0.118,0.159 10 3 1.364,1.748 1.491,1.894 0.127,0.146 10 4 1.553,1.752 1.671,1.899 0.118,0.147 10 5 2.935,1.739 3.12,1.897 0.185,0.158 10 15
*a Measuring Point


Pull the No. 2 chain sub-assembly with a force of 147 N (15 kgf, 33.1 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 links.

Maximum chain elongation:

137.6 mm (5.417 in.)


NOTICE:

Perform the measurement at 3 random places. Use the average of the measurements.


If the average elongation is greater than the maximum, replace the chain sub-assembly.


Hide 13521 9.INSPECT CRANKSHAFT TIMING SPROCKET

a.

Place the chain around the sprocket.


b.
A109646

Using a vernier caliper, measure the sprocket diameter with the chain sub-assembly.

Minimum sprocket diameter (with chain):

61.4 mm (2.418 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain and sprocket.


Hide 13530 10.INSPECT IDLE SPROCKET ASSEMBLY

a.

Place the chain around the sprocket.


b.
A109647

Using a vernier caliper, measure the sprocket diameter with the chain.

Minimum sprocket diameter (with chain):

61.4 mm (2.418 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain and sprocket.


Hide 11.INSPECT IDLE GEAR SHAFT OIL CLEARANCE

a.
A109648

Using a micrometer, measure the idle gear shaft diameter.

Standard idle gear shaft diameter:

22.987 to 23.000 mm (0.9050 to 0.9055 in.)



b.
A120673

Using a caliper gauge, measure the inside diameter of the idle sprocket assembly.

Standard idle gear inside diameter:

23.020 to 23.030 mm (0.9063 to 0.9067 in.)



c.

Subtract the idle gear shaft diameter measurement from the idle sprocket inside diameter measurement.

Standard oil clearance:

0.020 to 0.043 mm (0.000787 to 0.00169 in.)


Maximum oil clearance:

0.093 mm (0.00366 in.)


If the thrust oil clearance is greater than the maximum, replace the idle gear shaft and idle sprocket assembly.


Hide 13540 12.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A097905
2.281,0.865 2.531,0.615 false 1.531,1.521 2.177,1.698 false 2.563,0.5 2.729,0.646 0.167,0.146 10 false *1 2.219,1.625 2.396,1.771 0.177,0.146 10 false *2
*1 Plunger
*2 Stopper Plate


Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.

If necessary, replace the No. 1 chain tensioner assembly.


Hide 13550 13.INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A293118
3.063,0.74 3.375,0.938 0.313,0.198 10 *a 0.073,1.708 0.385,1.906 0.313,0.198 10 *a
*a Depth


Check that the plunger moves smoothly.


b.

Using a vernier caliper, measure the worn depth of the No. 2 chain tensioner assembly.

Maximum depth:

0.9 mm (0.0354 in.)


If the depth is greater than the maximum, replace the No. 2 chain tensioner assembly.


Hide 13560A 14.INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A293119
3.115,0.708 3.427,0.906 0.313,0.198 10 false *a 0.167,1.635 0.479,1.833 0.313,0.198 10 false *a
*a Depth


Check that the plunger moves smoothly.


b.

Using a vernier caliper, measure the worn depth of the No. 3 chain tensioner assembly.

Maximum depth:

0.9 mm (0.0354 in.)


If the depth is greater than the maximum, replace the No. 3 chain tensioner assembly.


Hide 13559 15.INSPECT CHAIN TENSIONER SLIPPER

a.
A106110
3.031,1.375 3.26,1.583 0.229,0.208 10 *a
*a Depth


Measure the worn depth of the chain tensioner slipper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is greater than the maximum, replace the chain tensioner slipper.


Hide 13561 16.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A106111
2.948,1.385 3.313,1.656 0.365,0.271 10 *a
*a Depth


Using a vernier caliper, measure the worn depth of the No. 1 chain vibration damper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is greater than the maximum, replace the No. 1 chain vibration damper.


Hide 13562 17.INSPECT NO. 2 CHAIN VIBRATION DAMPER

a.
A106112
2.01,1.427 2.583,1.688 0.573,0.26 10 *a
*a Depth


Using a vernier caliper, measure the worn depth of the No. 2 chain vibration damper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is greater than the maximum, replace the No. 2 chain vibration damper.


Hide 18.INSPECT CAMSHAFT THRUST CLEARANCE

a.

Inspect the bank 1 camshaft thrust clearance.


ii.
A109682

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.08 to 0.13 mm (0.00315 to 0.00512 in.)


Maximum thrust clearance:

0.15 mm (0.00591 in.)


If the thrust clearance is greater than the maximum, replace the camshaft housing. If the thrust surface is damaged, replace the camshaft.



b.

Inspect the bank 2 camshaft thrust clearance.


ii.

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.08 to 0.13 mm (0.00315 to 0.00512 in.)


Maximum thrust clearance:

0.15 mm (0.00591 in.)


If the thrust clearance is greater than the maximum, replace the camshaft housing. If the thrust surface is damaged, replace the camshaft.



Hide 19.INSPECT CAMSHAFT OIL CLEARANCE (for Bank 1)

a.

Clean the camshaft bearing caps, camshaft housing and camshaft journals.


b.

Place the camshafts on the camshaft housing.


c.
A120715
1.297,1.746 1.461,1.915 0.164,0.169 10 *1 1.583,0.968 1.39,1.723 false
*1 Surge Tank Side


Lay a strip of Plastigage across each camshaft journal.


d.

Install the camshaft bearing caps.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>CAMSHAFT>INSTALLATION

NOTICE:

Do not turn the camshaft.



e.

Remove the camshaft bearing caps.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL


f.
A129756
1.49,1.073 1.156,1.771 1.156,1.771 1.01,1.771 false 2.854,3.042 2.469,2.51 2.469,2.51 2.292,2.51 false 2.469,2.51 2.854,3.885 false 0.344,2.219 0.542,2.219 0.542,2.219 2.146,3.094 false 1.344,3.104 0.542,2.229 false 0.542,2.219 0.542,3.104 false 0.552,3.875 1.354,4.375 1.354,4.375 2.146,3.875 false 1.354,3.885 1.354,4.375 false 0.813,1.688 0.969,1.844 0.156,0.156 10 *1 2.125,2.427 2.281,2.583 0.156,0.156 10 *2 0.135,2.146 0.292,2.302 0.156,0.156 10 *3 1.229,4.396 1.385,4.552 0.156,0.156 10 *3
*1 Plastigage
*2 No. 1 Journal
*3 Other Journals


Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Oil Clearance
No. 1 journal 0.032 to 0.063 mm (0.00126 to 0.00248 in.)
Other journals 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum Oil Clearance:
Item Oil Clearance
No. 1 journal 0.10 mm (0.00394 in.)
Other journals 0.09 mm (0.00354 in.)


If the oil clearance is greater than the maximum, replace the camshaft. If necessary, replace the camshaft housing.


Hide 20.INSPECT CAMSHAFT OIL CLEARANCE (for Bank 2)

a.

Clean the camshaft bearing caps, camshaft housing and camshaft journals.


b.

Place the camshafts on the camshaft housing.


c.
A120717
1.25,0.066 1.416,0.242 0.166,0.176 10 *1 1.81,0.713 1.434,0.152 false
*1 Plastigage


Lay a strip of Plastigage across each camshaft journal.


d.

Install the camshaft bearing caps.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>CAMSHAFT>INSTALLATION

NOTICE:

Do not turn the camshaft.



e.

Remove the camshaft bearing caps.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL


f.
A129758
1.781,0.729 0.979,0.24 false 0.552,2.99 1.052,2.354 1.052,2.354 0.615,3.656 false 1.417,2.938 2.302,2.354 2.302,2.354 2.115,2.917 true 1.427,3.708 2.135,4.167 2.135,4.167 2.792,3.708 false 2.792,3.031 2.135,4.146 2.135,4.146 2.115,3.708 false 0.75,0.146 0.938,0.313 0.188,0.167 10 false *1 1.094,2.219 1.281,2.385 0.188,0.167 10 false *2 2.354,2.24 2.542,2.406 0.188,0.167 10 false *3 2.031,4.198 2.219,4.365 0.188,0.167 10 false *3
*1 Plastigage
*2 No. 1 Journal
*3 Other Journals


Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Oil Clearance
No. 1 journal 0.032 to 0.063 mm (0.00126 to 0.00248 in.)
Other journals 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum Oil Clearance:
Item Oil Clearance
No. 1 journal 0.10 mm (0.00394 in.)
Other journals 0.09 mm (0.00354 in.)


If the oil clearance is greater than the maximum, replace the camshaft. If necessary, replace the camshaft housing sub-assembly.


Hide 17105 21.INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY LH

a.
A134936

Using a precision straightedge and feeler gauge, measure the warpage on the contact surface of the cylinder head.

Maximum warpage:

0.7 mm (0.0276 in.)


HINT:

The maximum allowable warpage of each installation surface is 0.3 mm (0.0118 in.).


If the warpage is greater than the maximum, replace the manifold.


Hide 17104 22.INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY RH

a.
A134937

Using a precision straightedge and feeler gauge, measure the warpage on the contact surface of the cylinder head.

Maximum warpage:

0.7 mm (0.0276 in.)


HINT:

The maximum allowable warpage of each installation surface is 0.3 mm (0.0118 in.).


If the warpage is greater than the maximum, replace the manifold.


Hide 17111 23.INSPECT INTAKE MANIFOLD

A134934
0.153,0.02 0.358,0.252 0.205,0.233 10 *a 0.153,2.074 0.344,2.306 0.191,0.233 10 *b
*a Cylinder Head Side
*b Surge Tank Side


a.

Cylinder head side:

i.

Using a precision straightedge and feeler gauge, measure the surface contacting the cylinder head for warpage.

Maximum warpage:

0.1 mm (0.00394 in.)

If the warpage is greater than the maximum, replace the intake manifold.




b.

Surge tank side:

i.

Using a precision straightedge and feeler gauge, measure the surface contacting the surge tank for warpage.

Maximum warpage:

0.1 mm (0.00394 in.)

If the warpage is greater than the maximum, replace the intake manifold.