Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › CAMSHAFT
RM2030EQ _51 Engine / Hybrid System _014635 2GR-FE ENGINE MECHANICAL _0074412 CAMSHAFT A

2GR-FE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the camshaft, No. 2 camshaft, No. 3 camshaft, No. 4 camshaft, camshaft timing gear assembly, camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 13053 1.INSTALL NO. 3 CAMSHAFT

a.

Apply a light coat of engine oil to the No. 3 camshaft journals and camshaft housing sub-assembly LH.


b.

Install the No. 3 camshaft to the camshaft housing sub-assembly LH.

HINT:

Perform "Inspection After Repair" after replacing the No. 3 camshaft.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 13054 2.INSTALL NO. 4 CAMSHAFT

a.

Apply a light coat of engine oil to the No. 4 camshaft journals and camshaft housing sub-assembly LH.


b.

Install the No. 4 camshaft to the camshaft housing sub-assembly LH.

HINT:

Perform "Inspection After Repair" after replacing the No. 4 camshaft.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 3.INSTALL CAMSHAFT BEARING CAP (for Bank 2)

a.

Apply engine oil to the camshaft bearing caps.


b.
A134960

Make sure of the marks and numbers on the camshaft bearing caps and place them in each proper position and direction.


c.
A132217N04
1.427,0 1.542,0.146 0.115,0.146 10 false 1 2.073,0 2.188,0.146 0.115,0.146 10 false 3 3.167,0.417 3.281,0.563 0.115,0.146 10 false 7 3.198,1.063 3.313,1.208 0.115,0.146 10 false 8 2.073,1.469 2.188,1.615 0.115,0.146 10 true 4 1.406,1.469 1.521,1.615 0.115,0.146 10 true 2 0.198,1.042 0.313,1.188 0.115,0.146 10 false 6 0.198,0.375 0.313,0.521 0.115,0.146 10 false 5

Temporarily tighten the 8 bolts in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11104A 4.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

HINT:

Type A and Type B can be distinguished by the shape of the compression spring.


A336090C01
0.052,0.083 1.708,4.49 1.656,4.406 1.771,0.073 3.396,4.479 1.625,4.406 1.156,2.323 1.156,2.094 false 2.823,2.313 2.823,2.083 false 1.208,2.99 0.885,2.99 false 2.917,3.01 2.594,3.01 false 1.26,3.938 0.938,3.938 false 2.979,3.979 2.646,3.979 false 0.094,0.104 0.438,0.333 0.344,0.229 12 false *A 1.813,0.094 2.188,0.375 0.375,0.281 12 false *B 1.094,2.375 1.406,2.531 0.313,0.156 10 false *1 1.271,2.917 1.583,3.073 0.313,0.156 10 false *2 1.313,3.875 1.625,4.031 0.313,0.156 10 false *3 0.635,2.49 0.948,2.646 0.313,0.156 10 false *a 1.417,0.917 1.646,1.125 0.229,0.208 10 false *b 3.125,0.906 3.354,1.115 0.229,0.208 10 false *b 2.354,2.479 2.667,2.635 0.313,0.156 10 false *a 2.76,2.354 3.073,2.51 0.313,0.156 10 false *1 2.979,2.927 3.292,3.083 0.313,0.156 10 false *2 3.031,3.917 3.344,4.073 0.313,0.156 10 false *3
*A Type A
*B Type B
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Spring Retainer
*3 Inner Compression Spring
*a Valve Spring Retainer Diameter
*b No. 1 Valve Rocker Arm Sub-assembly Roller Width


Type No. 1 Valve Rocker Arm Sub-assembly Roller Width Valve Spring Retainer Diameter Inner Compression Spring Shape
A 10.7 mm (0.421 in.) 23.4 mm (0.921 in.) Straight
B 8.0 mm (0.315 in.) 18.9 mm (0.744 in.) Taper

a.
A333606C01
1.802,0.458 2.01,0.24 2.01,0.24 2.208,0.24 false 0.823,1.219 1.104,1.219 false 2.104,0.802 2.573,0.802 false 1.104,1.865 1.354,1.865 1.354,1.865 2.021,0.875 false 1.792,2.719 2,2.5 2,2.5 2.198,2.5 false 0.823,3.448 1.104,3.448 false 2.115,3.073 2.583,3.073 false 1.104,4.146 1.354,4.146 1.354,4.146 2.021,3.156 false 0.24,0.083 0.688,0.385 0.448,0.302 12 false *A 0.281,2.354 0.708,2.594 0.427,0.24 12 false *B 2.26,2.438 2.573,2.594 0.313,0.156 10 false *1 0.625,1.146 0.938,1.302 0.313,0.156 10 false *2 0.917,1.792 1.229,1.948 0.313,0.156 10 false *3 2.271,0.177 2.583,0.333 0.313,0.156 10 false *1 2.635,3.01 2.948,3.167 0.313,0.156 10 false *4 2.635,0.729 2.948,0.885 0.313,0.156 10 false *4 0.927,4.083 1.24,4.24 0.313,0.156 10 false *3 0.635,3.375 0.948,3.531 0.313,0.156 10 false *2
*A Type A
*B Type B
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem
*4 Valve Stem Cap


Make sure that the valve rocker arm is installed as shown in the illustration.


b.
A187877C02
2.927,0.125 2.396,0.521 true 2.958,0.042 3.125,0.208 0.167,0.167 10 false *a
*a Seal packing diameter
(3.5 to 4.5 mm)


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.5 mm (0.138 to 0.177 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing sub-assembly LH within 3 minutes and tighten the bolts.

·

Do not start the engine for at least 2 hours after installing.




c.
A292456C02
1.188,2.51 1.802,2.938 1.802,2.938 2.385,2.51 true 1.719,2.219 2.031,2.417 0.313,0.198 10 false *a 1.74,2.99 2.052,3.188 0.313,0.198 10 false *1 0.875,1.031 1.031,1.229 0.156,0.198 10 false 1 0.875,1.656 1.177,1.958 0.302,0.302 10 false 2 0.885,0.448 1.104,0.708 0.219,0.26 10 false 3 1.646,1.063 1.854,1.292 0.208,0.229 10 false 4 2.604,1.729 2.823,2.01 0.219,0.281 10 false 5 2.583,0.469 2.813,0.771 0.229,0.302 10 false 6 0.094,1.135 0.292,1.375 0.198,0.24 10 false 7 0.094,1.875 0.25,2.073 0.156,0.198 10 false 8 0.094,0.333 0.375,0.594 0.281,0.26 10 false 9 2.323,1.063 2.635,1.26 0.313,0.198 10 false 10 2.833,2.021 3.146,2.219 0.313,0.198 10 false 11 3.083,0.74 3.302,1.031 0.219,0.292 10 false 12 3.156,1.51 3.417,1.802 0.26,0.292 10 false 13
*1 Knock Pin
*a Front View


Install the camshaft housing sub-assembly LH and tighten the 13 bolts in the order shown in the illustration.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:
·

When installing the camshaft housing sub-assembly LH, it is necessary to correctly position the camshafts as shown in the illustration. Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated, valve contact with a piston at TDC will occur.

·

If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly LH, clean the installation surfaces, and reapply seal packing.

·

If the camshaft housing sub-assembly LH is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.




d.
A292454N04
0.094,0.708 0.333,0.906 0.24,0.198 10 1 0.938,0.583 1.156,0.833 0.219,0.25 10 2 2.563,0.615 2.781,0.854 0.219,0.24 10 3 3.104,0.698 3.375,0.979 0.271,0.281 10 4 0.115,1.385 0.385,1.656 0.271,0.271 10 5 0.938,1.271 1.156,1.552 0.219,0.281 10 6 2.552,1.313 2.781,1.563 0.229,0.25 10 7 3.156,1.396 3.427,1.656 0.271,0.26 10 8

Tighten the 8 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 13511 5.INSTALL CAMSHAFT

a.

Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly RH.


b.

Install the camshaft to the camshaft housing sub-assembly RH.

HINT:

Perform "Inspection After Repair" after replacing the camshaft.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 13512 6.INSTALL NO. 2 CAMSHAFT

a.

Apply a light coat of engine oil to the No. 2 camshaft journals and camshaft housing sub-assembly RH.


b.

Install the No. 2 camshaft to the camshaft housing sub-assembly RH.

HINT:

Perform "Inspection After Repair" after replacing the No. 2 camshaft.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 7.INSTALL CAMSHAFT BEARING CAP (for Bank 1)

a.

Apply engine oil to the camshaft bearing caps.


b.
A131902

Make sure of the marks and numbers on the camshaft bearing caps and place them in each proper position and direction.


c.
A131903N04
0.646,0.156 0.771,0.313 0.125,0.156 10 false 7 1.375,0.156 1.5,0.313 0.125,0.156 10 false 3 2.156,0.156 2.281,0.313 0.125,0.156 10 false 1 3.052,0.365 3.177,0.521 0.125,0.156 10 false 5 2.833,1.75 2.958,1.906 0.125,0.156 10 true 6 2.146,1.76 2.271,1.917 0.125,0.156 10 true 2 1.375,1.771 1.5,1.927 0.125,0.156 10 true 4 0.625,1.781 0.75,1.938 0.125,0.156 10 true 8

Temporarily tighten the 8 bearing cap bolts in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11103C 8.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

HINT:

Type A and Type B can be distinguished by the shape of the compression spring.


A336090C01
0.052,0.083 1.708,4.49 1.656,4.406 1.771,0.073 3.396,4.479 1.625,4.406 1.156,2.323 1.156,2.094 false 2.823,2.313 2.823,2.083 false 1.208,2.99 0.885,2.99 false 2.917,3.01 2.594,3.01 false 1.26,3.938 0.938,3.938 false 2.979,3.979 2.646,3.979 false 0.094,0.104 0.438,0.333 0.344,0.229 12 false *A 1.813,0.094 2.188,0.375 0.375,0.281 12 false *B 1.094,2.375 1.406,2.531 0.313,0.156 10 false *1 1.271,2.917 1.583,3.073 0.313,0.156 10 false *2 1.313,3.875 1.625,4.031 0.313,0.156 10 false *3 0.635,2.49 0.948,2.646 0.313,0.156 10 false *a 1.417,0.917 1.646,1.125 0.229,0.208 10 false *b 3.125,0.906 3.354,1.115 0.229,0.208 10 false *b 2.354,2.479 2.667,2.635 0.313,0.156 10 false *a 2.76,2.354 3.073,2.51 0.313,0.156 10 false *1 2.979,2.927 3.292,3.083 0.313,0.156 10 false *2 3.031,3.917 3.344,4.073 0.313,0.156 10 false *3
*A Type A
*B Type B
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Spring Retainer
*3 Inner Compression Spring
*a Valve Spring Retainer Diameter
*b No. 1 Valve Rocker Arm Sub-assembly Roller Width


Type No. 1 Valve Rocker Arm Sub-assembly Roller Width Valve Spring Retainer Diameter Inner Compression Spring Shape
A 10.7 mm (0.421 in.) 23.4 mm (0.921 in.) Straight
B 8.0 mm (0.315 in.) 18.9 mm (0.744 in.) Taper

a.
A333606C01
1.802,0.458 2.01,0.24 2.01,0.24 2.208,0.24 false 0.823,1.219 1.104,1.219 false 2.104,0.802 2.573,0.802 false 1.104,1.865 1.354,1.865 1.354,1.865 2.021,0.875 false 1.792,2.719 2,2.5 2,2.5 2.198,2.5 false 0.823,3.448 1.104,3.448 false 2.115,3.073 2.583,3.073 false 1.104,4.146 1.354,4.146 1.354,4.146 2.021,3.156 false 0.24,0.083 0.688,0.385 0.448,0.302 12 false *A 0.281,2.354 0.708,2.594 0.427,0.24 12 false *B 2.26,2.438 2.573,2.594 0.313,0.156 10 false *1 0.625,1.146 0.938,1.302 0.313,0.156 10 false *2 0.917,1.792 1.229,1.948 0.313,0.156 10 false *3 2.271,0.177 2.583,0.333 0.313,0.156 10 false *1 2.635,3.01 2.948,3.167 0.313,0.156 10 false *4 2.635,0.729 2.948,0.885 0.313,0.156 10 false *4 0.927,4.083 1.24,4.24 0.313,0.156 10 false *3 0.635,3.375 0.948,3.531 0.313,0.156 10 false *2
*A Type A
*B Type B
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem
*4 Valve Stem Cap


Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.


b.
A187878C03
1.979,0.146 1.698,0.521 true 2,0.042 2.167,0.208 0.167,0.167 10 *a
*a Seal packing diameter
(3.5 to 4.5 mm)


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.5 mm (0.138 to 0.177 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing sub-assembly RH within 3 minutes and tighten the bolts.

·

Do not start the engine for at least 2 hours after installing.




c.
A131905C03
1.042,2.521 1.573,3.083 1.573,3.083 2.438,2.552 false 0.146,1.813 0.271,1.969 0.125,0.156 10 false 8 0.146,1.146 0.271,1.302 0.125,0.156 10 false 7 0.146,0.615 0.271,0.771 0.125,0.156 10 false 9 0.979,0.615 1.104,0.771 0.125,0.156 10 true 6 0.979,1.177 1.104,1.333 0.125,0.156 10 true 4 0.927,1.656 1.052,1.813 0.125,0.156 10 true 5 2.677,1.781 2.802,1.938 0.125,0.156 10 true 2 2.646,1.083 2.771,1.24 0.125,0.156 10 true 1 2.635,0.521 2.76,0.677 0.125,0.156 10 true 3 3.156,0.698 3.354,0.854 0.198,0.156 10 true 12 3.156,1.156 3.354,1.313 0.198,0.156 10 false 10 3.156,1.979 3.354,2.135 0.198,0.156 10 false 11 1.542,2.146 1.708,2.302 0.167,0.156 10 false *a 1.469,3.115 1.635,3.271 0.167,0.156 10 false *1 3,2.354 3.25,2.51 0.25,0.156 10 false 45°
*1 Knock Pin
*a Front View


Install the camshaft housing sub-assembly RH and tighten the 12 bolts in the order shown in the illustration.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:
·

When installing the camshaft housing RH, it is necessary to correctly position the camshafts as shown in the illustration.

Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated, valve contact with a piston at TDC will occur.

·

If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly RH, clean the installation surfaces, and reapply seal packing.

·

If the camshaft housing sub-assembly RH is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.




d.
A292441N04
2.844,0.115 3.021,0.365 0.177,0.25 10 1 2.156,0.188 2.354,0.448 0.198,0.26 10 2 1.375,0.188 1.604,0.5 0.229,0.313 10 3 0.656,0.188 0.823,0.448 0.167,0.26 10 4 2.854,1.729 3.021,2.031 0.167,0.302 10 5 2.167,1.729 2.344,1.969 0.177,0.24 10 6 1.396,1.719 1.563,1.938 0.167,0.219 10 7 0.646,1.719 0.844,1.927 0.198,0.208 10 8

Tighten the 8 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 13560A 9.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A121266C04
1.406,1 1.052,1.188 true 1.656,0.938 1.031,0.375 true 1.042,2.417 1.208,2.573 0.167,0.156 10 false *a 0.844,1.104 1,1.26 0.156,0.156 10 false *2 0.833,0.292 0.99,0.448 0.156,0.156 10 false *1
*1 Plunger
*2 Pin
*a Push


Install the No. 3 chain tensioner assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

While pushing in the tensioner, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to hold it.


Hide 13080 10.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

a.
A292458C02
1.875,0.125 2.188,0.125 2.188,0.125 2.604,1.156 true 0.917,0.49 1.104,0.135 1.104,0.135 1.594,0.135 false 1.677,0.052 1.99,0.25 0.313,0.198 10 *1 1.938,1.615 2.25,1.813 0.313,0.198 10 *2
*1 Timing Mark
*2 Mark Plate


Align the mark plates (yellow) with the timing marks of the camshaft timing gear assemblies as shown in the illustration.


b.

Apply a light coat of engine oil to the bolt threads and bolt-seating surface.


c.

Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear assembly with the No. 2 chain sub-assembly installed.


d.
A182778C03
1.469,0.104 1.208,0.719 false 2.615,1.865 2.677,1.719 false 0.896,0.125 0.594,0.229 false 1.5,0.01 1.802,0.156 0.302,0.146 10 false SST 2.469,1.906 2.625,2.063 0.156,0.156 10 false *b 0.958,0.031 1.125,0.188 0.167,0.156 10 false *a
*a Turn
*b Hold


Using SST to hold the hexagonal portion of each camshaft, tighten the flange bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.

SST
09922-10010  

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


e.

Remove the pin from the No. 3 chain tensioner assembly.

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly or camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 13550 11.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A121265C07
2.229,2.635 2.688,2.24 true 1.948,2.719 2.552,3.146 true 3.104,1.208 3.26,1.365 0.156,0.156 10 false *a 2.76,2.125 2.927,2.281 0.167,0.156 10 false *2 2.583,3.052 2.75,3.219 0.167,0.167 10 false *1
*1 Plunger
*2 Pin
*a Push


Install the No. 2 chain tensioner assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

While pushing in the No. 2 chain tensioner assembly, insert a pin of 1.0 mm (0.0394 in.) diameter into the hole to hold it.


Hide 13050 12.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

a.
A124048C03
1.583,0.156 1.792,0.354 0.208,0.198 10 *1 1.646,1.531 1.854,1.729 0.208,0.198 10 *2
*1 Timing Mark
*2 Mark Plate


Align the mark plates (yellow) with the timing marks of the camshaft timing gear assemblies as shown in the illustration.


b.

Apply a light coat of engine oil to the bolt threads and bolt-seating surface.


c.

Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear assembly with the No. 2 chain sub-assembly installed.


d.
A182777C06
0.938,0.25 1.604,0.5 false 0.854,1.885 0.531,1.646 false 2.563,0.125 2.854,0.26 false 0.573,0.167 0.875,0.344 0.302,0.177 10 false SST 0.896,1.792 1.052,1.948 0.156,0.156 10 false *b 2.375,0.021 2.542,0.177 0.167,0.156 10 false *a
*a Turn
*b Hold


Using SST to hold the hexagonal portion of each camshaft, tighten the flange bolts of the camshaft timing gear assembly and the camshaft timing exhaust gear assembly.

SST
09922-10010  

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


e.

Remove the pin from the No. 2 chain tensioner assembly.

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly or camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 13530 13.INSTALL IDLE SPROCKET ASSEMBLY

Hide 13506 14.INSTALL CHAIN SUB-ASSEMBLY

Hide 13559 15.INSTALL CHAIN TENSIONER SLIPPER

Hide 13540 16.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 11301C 18.INSTALL TIMING CHAIN CASE OIL SEAL

Hide 11302 19.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 12101 20.INSTALL OIL PAN SUB-ASSEMBLY

Hide 15104 21.INSTALL OIL STRAINER SUB-ASSEMBLY

Hide 12102A 22.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

Hide 11201 23.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11202 24.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 16323 25.INSTALL WATER INLET HOUSING

Hide 12315 26.INSTALL NO. 1 FRONT ENGINE MOUNTING BRACKET LH

Hide 25860A 31.INSTALL NO. 1 VACUUM SWITCHING VALVE

Hide 16604 33.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 11322F 34.INSTALL NO. 2 TIMING GEAR COVER

Hide 11452 35.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 15781 36.INSTALL NO. 1 OIL COOLER BRACKET

a.

Install a new gasket to the oil pan sub-assembly.


b.

Install the No. 1 oil cooler bracket with oil cooler pipe with the 3 bolts and 3 nuts.

Torque:
21 N*m (214 kgf*cm, 16 ft.*lbf)


Hide 15710 37.INSTALL OIL COOLER ASSEMBLY

Hide 16620 38.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 17105 39.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 17168 40.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 12142 42.INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 17104 43.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 12327A 45.INSTALL NO. 2 ENGINE MOUNTING STAY RH

Hide 22267A 47.INSTALL THROTTLE BODY BRACKET

Hide 17125 48.INSTALL NO. 1 SURGE TANK STAY

Hide 17190 49.INSTALL INTAKE AIR SURGE TANK ASSEMBLY

Hide 51.REMOVE ENGINE STAND

Hide 32101 52.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY