Home › Engine / Hybrid System › 2GR-FE FUEL › FUEL INJECTOR
RM2030EQ _51 Engine / Hybrid System _014636 2GR-FE FUEL _0074421 FUEL INJECTOR A

2GR-FE FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

a.
A129475C02
2.865,1.438 2.865,1.583 false 2.802,1.625 3.177,1.906 0.375,0.281 10 *1
*1 O-ring


Apply a light coat of spindle oil or gasoline to new O-rings, and install them to each injector.


b.
A129476C01
2.128,1.245 2.363,1.429 0.235,0.184 10 *a
*a Turn
V100135

Push


Apply a light coat of spindle oil or gasoline where the fuel delivery pipe contacts each O-ring.


c.

Push and twist each fuel injector to install them into the fuel delivery pipe.


d.

Position each fuel injector connector outward.

NOTICE:
·

Be careful not to twist the O-rings.

·

After installing a fuel injector, check that it turns smoothly. If not, reinstall it with a new O-ring.



HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 23807 2.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A292481

Install 6 new injector vibration insulators to the intake manifold.


b.

Place the fuel delivery pipe with the 6 fuel injectors in position on the intake manifold.

NOTICE:

Be careful not to drop the fuel injectors when installing the fuel delivery pipe.



c.
A137334

Temporarily install the 5 bolts which are used to hold the fuel delivery pipe to the intake manifold.

NOTICE:

After installing the fuel injectors, check that they turn smoothly. If not, reinstall the injectors with new O-rings.



d.
A129471

Tighten the 5 bolts which are used to hold the fuel delivery pipe to the intake manifold.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.
A137341

Connect the 6 fuel injector connectors.


Hide 23901 3.CONNECT FUEL TUBE SUB-ASSEMBLY

a.
A292482C01
0.938,1.938 1.917,1.625 false 2.583,3.74 1.594,2.792 1.594,2.792 2.594,3.365 false 1.313,3.948 1.563,3.76 false 2.177,3.719 2.042,4.063 2.042,4.063 2.01,3.719 false 2.854,4.052 2.813,3.688 false 0.781,1.885 1.094,2.083 0.313,0.198 10 *1 1.417,2.708 1.729,2.906 0.313,0.198 10 *2 1.146,3.875 1.458,4.073 0.313,0.198 10 *3 1.927,4.073 2.24,4.271 0.313,0.198 10 *4 2.792,4.083 3.104,4.281 0.313,0.198 10 *5
*1 No. 2 Fuel Pipe Clamp
*2 Retainer
*3 Fuel Tube Connector
*4 O-ring
*5 Fuel Pipe
V100135

Push


Push in the fuel tube connector onto the fuel pipe until the fuel tube connector makes a "click" sound.

NOTICE:
·

Before connecting the fuel tube connector, make sure that it is not damaged. Make sure that there is no dirt present on the connecting surfaces.

·

After connecting, check that the fuel tube connector and the fuel pipe are securely connected by pulling on them.




b.

Install the No. 2 fuel pipe clamp.


Hide 17190 4.INSTALL INTAKE AIR SURGE TANK ASSEMBLY

Hide 5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION