Home › Engine / Hybrid System › 2GR-FE COOLING › WATER PUMP
RM2030EQ _51 Engine / Hybrid System _014639 2GR-FE COOLING _0074443 WATER PUMP A

2GR-FE COOLING  WATER PUMP  INSTALLATION  


PROCEDURE

Hide 16100 1.INSTALL ENGINE WATER PUMP ASSEMBLY

a.
A293323C01
0.073,0.594 0.25,0.854 0.177,0.26 10 A 1.271,0.469 1.427,0.667 0.156,0.198 10 A 3.188,0.583 3.344,0.781 0.156,0.198 10 A 2.75,1.781 2.906,1.979 0.156,0.198 10 A 3.292,1.646 3.406,1.844 0.115,0.198 10 A 1.469,1.927 1.625,2.125 0.156,0.198 10 A 0.094,1.781 0.25,1.979 0.156,0.198 10 A 0.521,0.458 0.677,0.656 0.156,0.198 10 B 2.823,0.01 2.979,0.208 0.156,0.198 10 B 2.615,0.448 2.771,0.646 0.156,0.198 10 B 2.469,0.448 2.625,0.646 0.156,0.198 10 B 2.042,1.906 2.198,2.104 0.156,0.198 10 B 2.333,1.573 2.49,1.771 0.156,0.198 10 B 0.969,0.448 1.125,0.646 0.156,0.198 10 C 1.083,1.729 1.24,1.927 0.156,0.198 10 C 0.552,1.781 0.708,1.979 0.156,0.198 10 A

Install a new gasket and the engine water pump assembly together with the water pump pulley with the 16 bolts.

Torque:
Bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
Bolt B and C : 11 N*m (112 kgf*cm, 8 ft.*lbf)

NOTICE:
·

Make sure that there is no oil on the threads of bolts A.

·

Be sure to replace 2 bolts C with new ones or reuse them after applying adhesive 1344.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent





Hide 16173 2.INSTALL WATER PUMP PULLEY

a.

Temporarily install the water pump pulley with the 4 bolts.


b.
A293326C01
1.302,1.833 2.865,1.969 2.865,1.969 1.938,1.417 false 0.938,0.688 1.375,1.156 false 0.781,0.563 1.094,0.719 0.313,0.156 10 *1 0.833,1.427 1.146,1.583 0.313,0.156 10 *a 2.917,1.917 3.344,2.271 0.427,0.354 10 SST
*1 Union Nut Wrench
*a 170 mm


Using SST, hold the water pump pulley.

SST
09960-10010  (09962-01000, 09963-00700)


c.

Using SST and union nut wrench, tighten the 4 bolts.

SST
09961-00950  

Torque:
without SST : 21 N*m (214 kgf*cm, 15 ft.*lbf)
with SST : 11 N*m (112 kgf*cm, 8 ft.*lbf)

NOTICE:
·

The "with SST" torque value is effective when using SST with a fulcrum length of 170 mm (6.69 in.) and a torque wrench with a fulcrum length of 180 mm (7.09 in.).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The "with SST" torque value is effective when SST is parallel to the torque wrench.




Hide 16323 3.INSTALL WATER INLET HOUSING

a.

Install 2 new O-rings.


b.

Install the water inlet housing with the 2 bolts and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Be careful not to allow the O-ring to get caught between the parts.



c.

Connect the water hose.


Hide 4.INSTALL V-RIBBED BELT TENSIONER PULLEY

a.
A235411C01
0.854,3.24 0.458,3.427 0.458,3.427 0.458,3.521 false 1.323,3.583 1.323,3.75 false 2.49,3.281 2.094,3.5 2.094,3.5 2.094,3.573 false 2.958,3.594 2.958,3.76 false 0.729,2.104 0.938,2.302 0.208,0.198 10 *a 2.417,2.115 2.635,2.302 0.219,0.188 10 *b 1.24,3.781 1.417,3.948 0.177,0.167 10 *2 0.365,3.563 0.563,3.729 0.198,0.167 10 *1 2.01,3.583 2.208,3.75 0.198,0.167 10 *1 2.865,3.781 3.042,3.948 0.177,0.167 10 *2
*1 Dust Shield
*2 Pulley
*a Correct
*b Incorrect


Install the V-ribbed belt tensioner pulley and dust shield with the bolt.

NOTICE:
·

Be careful when tightening the bolt because its thread is left-handed.

·

Install the dust shield in the direction shown in the illustration. Failure to do so may cause looseness.

·

Make sure to use the removed bolt. (Do not use another bolt even if it is the same size.)



Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


b.

Install the 5 mm bi-hexagon wrench.


Hide 16604 5.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 12315 6.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.

Temporarily install the front No. 1 engine mounting bracket LH with the 6 bolts.


b.
A255582

Fully tighten the 5 bolts.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


c.
A255659C01
0.76,1.021 0.938,1.188 0.177,0.167 10 *a
*a 150 mm


Using SST, fully tighten the bolt.

SST
09961-00950  

Torque:
without SST : 54 N*m (551 kgf*cm, 40 ft.*lbf)
with SST : 34 N*m (347 kgf*cm, 25 ft.*lbf)

NOTICE:
·

The "with SST" torque value is effective when using SST with a fulcrum length of 150 mm (5.905 in.) and a torque wrench with a fulcrum length of 260 mm (10.23 in.).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The "with SST" torque value is effective when SST is parallel to the torque wrench.




Hide 12309 7.INSTALL ENGINE MOVING CONTROL ROD SUB-ASSEMBLY

Hide 12327A 8.INSTALL NO. 2 ENGINE MOUNTING STAY RH (for Intake Manifold Side)

Hide 12327A 9.INSTALL NO. 2 ENGINE MOUNTING STAY RH (for Engine Mounting stay Side)