Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB
RM2030EQ _52 Drivetrain _014645 AXLE AND DIFFERENTIAL _0074483 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 89543 3.SEPARATE FRONT SPEED SENSOR

a.
C238961

Remove the bolt, disengage the clamp and separate the front speed sensor and front flexible hose.

NOTICE:

Be sure to separate the front speed sensor from the front shock absorber assembly completely.



b.
C238448

Remove the bolt and front speed sensor from the steering knuckle.

NOTICE:
·

Prevent foreign matter from contacting the sensor tip.

·

Be careful not to damage the front speed sensor.

·

Clean the speed sensor installation hole and the contact surfaces every time the speed sensor is removed.




Hide 4.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43512 5.REMOVE FRONT DISC

Hide 45470 6.SEPARATE TIE ROD ASSEMBLY

Hide 43420 7.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

a.
C238968C01
2.885,0.635 2.542,0.635 2.542,0.635 2.542,1.667 false 3.063,1 2.542,1 false 2.479,1.677 2.646,1.833 0.167,0.156 10 *a
*a Matchmark


Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.


b.

Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

If it is difficult to separate, tap the end of the front drive shaft assembly using a brass bar and a hammer.


Hide 48069 8.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

a.
C238969

Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.


Hide 9.REMOVE FRONT AXLE ASSEMBLY

a.
C238980

Remove the 2 bolts, 2 nuts and front axle assembly from the front shock absorber assembly.

NOTICE:
·

When removing the nuts, keep the bolts from rotating.

·

Be careful not to damage the drive shaft boot or speed sensor rotor.




Hide 43246B 10.REMOVE FRONT NO. 1 WHEEL BEARING DUST DEFLECTOR

a.
C238978C01
1.99,0.938 2.604,0.938 false 2.646,0.875 2.833,1.021 0.188,0.146 10 *1
*1 Vinyl Tape


Using a screwdriver with its tip wrapped with vinyl tape, remove the front No. 1 wheel bearing dust deflector.

NOTICE:

Be careful not to damage the steering knuckle.



Hide 43502G 11.REMOVE FRONT AXLE HUB HOLE SNAP RING

a.
C238979

Using snap ring pliers, remove the front axle hub hole snap ring.


Hide 43502C 12.REMOVE FRONT AXLE HUB SUB-ASSEMBLY

a.
C238975N02
1.792,0.51 1.792,0.26 1.792,0.26 2.24,0.26 false 2.177,2.396 2.177,2.76 false 2.26,0.188 2.76,0.427 0.5,0.24 10 SST 2.052,2.771 2.688,3.073 0.635,0.302 10 SST

Hold the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



b.

Using SST, remove the front axle hub sub-assembly.

SST
09520-00031  


c.
C167711N01
1.042,2.135 0.365,1.458 0.365,1.458 0.729,2.167 false 0.365,1.458 1.094,1.646 false 2.385,1.031 2.156,0.615 2.156,0.615 2.458,0.615 false 2.885,1.323 2.885,0.625 2.885,0.625 2.969,0.625 false 0.083,1.396 0.396,1.563 0.313,0.167 10 SST 1.865,0.552 2.177,0.719 0.313,0.167 10 SST 3,0.563 3.313,0.729 0.313,0.167 10 SST

Using SST and a press, remove the bearing inner race (outside) from the front axle hub sub-assembly.

SST
09555-55010  
09950-60010  (09951-00440)
09950-70010  (09951-07100)

NOTICE:

Be careful not to drop the front axle hub sub-assembly.



Hide 47782 13.REMOVE FRONT DISC BRAKE DUST COVER

a.
C238976

Remove the 4 bolts and front disc brake dust cover from the steering knuckle.


Hide 43502E 14.REMOVE FRONT AXLE HUB BEARING

a.
C202363C03
0.833,1.948 0.427,1.521 0.427,1.521 0.917,1.521 false 2.438,1.313 2.24,0.833 2.24,0.833 2.469,0.833 false 2.573,1.531 2.573,1.781 false 0.313,2.406 0.313,2.958 false 0.854,3.229 0.854,3.313 0.854,3.313 2.156,3.313 false 1.708,2.979 1.708,3.313 false 0.135,1.458 0.542,1.646 0.406,0.188 10 SST 1.938,0.771 2.344,0.958 0.406,0.188 10 SST 2.448,1.813 2.854,2.052 0.406,0.24 10 SST 0.25,2.979 0.417,3.146 0.167,0.167 10 *1 2.198,3.24 2.365,3.406 0.167,0.167 10 *2
*1 Steel Plate
*2 V-block


Place the bearing inner race (outside) on the front axle hub bearing.


b.

Using SST, a steel plate, V-blocks and a press, remove the front axle hub bearing from the steering knuckle.

SST
09950-60010  (09951-00440, 09952-06010)
09950-60020  (09951-00750)
09950-70010  (09951-07100)

NOTICE:

Keep the steering knuckle level.