Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER(for RHD)
RM2030EQ _54 Brake _014651 BRAKE SYSTEM (OTHER) _0074517 BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD)  INSTALLATION  


PROCEDURE

Hide 44696 1.INSTALL CHECK VALVE GROMMET

a.

Install a new check valve grommet to the brake booster assembly.


Hide 44730 2.INSTALL BRAKE VACUUM CHECK VALVE ASSEMBLY

a.

Install the brake vacuum check valve assembly to the brake booster assembly.


Hide 47264D 3.INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS

a.

Temporarily install the lock nut and brake master cylinder push rod clevis to the brake booster assembly.


b.
C105620C01
1.927,1.208 1.927,1.563 false 2.24,1.208 2.24,1.563 false 1.708,0.25 2.167,0.573 0.458,0.323 10 *a 1.844,1.573 2.135,1.771 0.292,0.198 10 *1 2.167,1.573 2.677,1.865 0.51,0.292 10 *2
*1 Lock Nut
*2 Brake Master Cylinder Push Rod Clevis
*a Push Rod Length


Set the push rod length as shown in the illustration.

Push rod length:

148.6 to 149.6 mm (5.86 to 5.88 in.)



c.

Tighten the lock nut.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 44785 4.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster assembly.


Hide 44610 5.INSTALL BRAKE BOOSTER ASSEMBLY

a.

Install the brake booster assembly to the vehicle body with the 4 nuts.

Torque:
13 N*m (131 kgf*cm, 9 ft.*lbf)

NOTICE:

Do not kink or damage the brake lines, air conditioning tube and accessory assembly or suction hose sub-assembly.



Hide 47264A 6.INSTALL PUSH ROD PIN

Hide 7.CONNECT BRAKE LINE

a.
C249108

Install 2 new clamps to the brake lines.


b.

Using a union nut wrench, connect the 2 brake lines to the brake actuator assembly.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt and dust to enter the brake lines.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




Hide 47371A 8.INSTALL NO. 1 BRAKE TUBE CLAMP

a.
C249114

Install a new No. 1 brake tube clamp to the vehicle body.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


b.

Engage the brake lines to the clamp.

NOTICE:

Do not kink or damage the brake lines.



Hide 88704 9.INSTALL SUCTION HOSE SUB-ASSEMBLY

a.

Remove the attached vinyl tape from the openings of the disconnected parts.


b.

Sufficiently apply compressor oil to a new O-ring, fitting surface of the suction hose sub-assembly and air conditioning unit.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring on the suction hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free from dirt or any foreign matter.



d.
C249110

Insert the suction hose sub-assembly to the air conditioning unit.

NOTICE:
·

Insert the pipe joint into the fitting hole securely.

·

Do not deform the piping.

·

Do not damage the clamp.




e.
C249115

Install the clamp with suction hose sub-assembly and air conditioning tube and accessory assembly to the No. 1 brake tube clamp.

NOTICE:
·

Do not deform the air conditioning tube and accessory assembly or suction hose sub-assembly.

·

Do not damage the clamp.




f.
C249116

Install the clamp to the brake actuator bracket assembly.

NOTICE:
·

Do not deform the suction hose sub-assembly.

·

Do not damage the clamp.




Hide 88710E 10.INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.

Remove the attached vinyl tape from the openings of the disconnected parts.


b.

Sufficiently apply compressor oil to 2 new O-rings, the fitting surface of the air conditioning tube and accessory assembly, cooler condenser assembly and air conditioning unit.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the 2 O-rings on the air conditioning tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free from dirt or any foreign matter.



d.

Insert the air conditioning tube and accessory assembly to the cooler condenser assembly.


e.

Install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


f.
C249113

Insert the air conditioning tube and accessory assembly to the air conditioning unit.

NOTICE:

Insert the pipe joint into the fitting hole securely.



g.

Turn the hook connector and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


h.
C249119

Install the clamp to the vehicle body and connect the pressure sensor connector.

NOTICE:
·

Do not deform the piping.

·

Do not damage the clamp.




Hide 53293C 11.INSTALL RADIATOR SIDE DEFLECTOR RH

Hide 47201 12.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 13.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 14.INSTALL FRONT BUMPER ASSEMBLY

Hide 15.INSPECT AND ADJUST BRAKE PEDAL