Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER(for RHD)
RM2030EQ _54 Brake _014651 BRAKE SYSTEM (OTHER) _0074517 BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal, Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 47201 3.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 4.REMOVE FRONT BUMPER ASSEMBLY

Hide 53293C 5.REMOVE RADIATOR SIDE DEFLECTOR RH

Hide 88710E 6.SEPARATE AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.
C249119

Disconnect the pressure sensor connector and separate the clamp.


b.
C249111

Remove the bolt from the hook connector.


c.
C249112

Turn the hook connector and separate the air conditioning tube and accessory assembly from the air conditioning unit.

NOTICE:
·

Do not deform the piping.

·

Do not damage the clamp.




d.
C239877

Remove the bolt and separate the air conditioning tube and accessory assembly from the cooler condenser assembly.

NOTICE:
·

Do not deform the piping.

·

Do not damage the clamp.




e.

Remove the 2 O-rings from the air conditioning tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88704 7.SEPARATE SUCTION HOSE SUB-ASSEMBLY

a.
C249116

Disengage the clamp from the brake actuator bracket assembly.


b.
C249115

Separate the clamp with suction hose sub-assembly and air conditioning tube and accessory assembly from the No. 1 brake tube clamp.


c.
C249109

Separate the suction hose sub-assembly from the air conditioning unit.

NOTICE:
·

Do not deform the piping.

·

Do not damage the clamp.




d.

Remove the O-ring from the suction hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 47371A 8.REMOVE NO. 1 BRAKE TUBE CLAMP

a.
C249114

Disengage the clamp from the brake lines.

NOTICE:

Do not kink or damage the brake lines.



b.

Remove the bolt and No. 1 brake tube clamp from the vehicle body.


Hide 9.REMOVE BRAKE LINE

a.
C239886

Using a union nut wrench, disconnect the 2 brake lines from the brake actuator assembly.


b.
C249108

Remove the 2 clamps to make the 2 brake lines free.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt and dust to enter the brake lines.




Hide 47264A 10.REMOVE PUSH ROD PIN

Hide 44610 11.REMOVE BRAKE BOOSTER ASSEMBLY

a.
C239888

Remove the 4 nuts and brake booster assembly from the vehicle body.

NOTICE:

Do not kink or damage the brake lines, air conditioning tube and accessory assembly or suction hose sub-assembly.



Hide 44785 12.REMOVE BRAKE BOOSTER GASKET

a.
C204573

Remove the brake booster gasket from the brake booster assembly.


Hide 47264D 13.REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS

a.

Loosen the lock nut and remove the brake master cylinder push rod clevis and lock nut.


Hide 44730 14.REMOVE BRAKE VACUUM CHECK VALVE ASSEMBLY

a.

Remove the brake vacuum check valve assembly from the brake booster assembly.


Hide 44696 15.REMOVE CHECK VALVE GROMMET

a.

Remove the check valve grommet from the brake booster assembly.