Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074591 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  Front Passenger Side Door Entry Unlock Function does not Operate  


DESCRIPTION

If the entry unlock function does not operate for the front passenger door only, but the entry lock function operates, the request code is being transmitted properly from the front passenger door. In this case, there may be a problem related to the touch sensor (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) [unlock sensor]).

WIRING DIAGRAM

B281953E08
1.302,0.694 1.687,0.854 0.385,0.161 10 ANT1 1.287,1.165 1.686,1.326 0.399,0.161 10 ANT2 0.31,3.454 1.2,3.614 0.89,0.161 10 V1*1, W1*2 3.154,4.07 3.894,4.231 0.74,0.161 10 *1: for LHD 3.154,4.35 3.894,4.511 0.74,0.161 10 *2: for RHD 1.352,3.009 1.696,3.153 0.344,0.144 10 GND 1.77,1.053 1.876,1.211 0.106,0.159 10 3 1.779,2.91 1.884,3.064 0.106,0.154 10 2 1.772,0.602 1.878,0.747 0.106,0.146 10 6 5.745,0.722 6.162,0.889 0.417,0.167 10 CLG2 5.745,1.19 6.175,1.346 0.43,0.156 10 CG2B 5.745,3.031 5.924,3.195 0.178,0.164 10 E 5.436,0.512 5.666,0.67 0.231,0.158 10 11 5.436,0.722 5.666,0.879 0.231,0.158 10 I78 5.436,1.184 5.666,1.341 0.231,0.158 10 I78 5.436,1.645 5.666,1.803 0.231,0.158 10 I78 5.436,2.107 5.666,2.265 0.231,0.158 10 I78 5.436,2.569 5.666,2.727 0.231,0.158 10 I78 5.403,3.031 5.668,3.189 0.266,0.158 10 A43 5.418,0.987 5.636,1.153 0.218,0.166 10 10 1.554,1.618 1.689,1.779 0.134,0.161 10 B 1.287,2.088 1.686,2.248 0.399,0.161 10 SENS 1.77,1.977 1.876,2.136 0.106,0.159 10 4 1.772,1.526 1.878,1.672 0.106,0.146 10 5 5.745,1.648 6.162,1.815 0.417,0.167 10 POS2 5.745,2.116 6.175,2.272 0.43,0.156 10 SEN2 5.428,1.436 5.606,1.594 0.178,0.158 10 21 5.428,1.911 5.62,2.077 0.192,0.166 10 23 1.287,2.564 1.686,2.725 0.399,0.161 10 TRG+ 1.77,2.44 1.876,2.598 0.106,0.159 10 1 5.745,2.573 6.175,2.73 0.43,0.156 10 TSW2 5.47,2.374 5.662,2.54 0.192,0.166 10 8 5.424,2.83 5.619,2.992 0.195,0.162 10 11 5.381,3.573 7.005,3.94 1.624,0.367 10 Certification ECU (Smart Key ECU Assembly) 0.312,3.62 2.103,4.198 1.792,0.578 10 Front Door Outside Handle Assembly (for Front Passenger Door)

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the intelligent tester with the engine switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR).

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (UNLOCK DETECTION SWITCH)

NG

2.READ VALUE USING INTELLIGENT TESTER (UNLOCK DETECTION SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Pos Front RH door unlock detection switch signal*1 UNLOCK or LOCK UNLOCK: Front RH door unlocked
LOCK: Front RH door locked
-
FL Door Lock Pos Front LH door unlock detection switch signal*2 UNLOCK or LOCK UNLOCK: Front LH door unlocked
LOCK: Front LH door locked
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Lock Pos
FL Door Lock Pos
50003 123 196,198
·

*1: for LHD

·

*2: for RHD


OK:

On the intelligent tester screen, the display changes between LOCK and UNLOCK as shown in the chart above.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (UNLOCK SENSOR)

NG

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

3.READ VALUE USING INTELLIGENT TESTER (UNLOCK SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P-Door Touch Sensor Front passenger door touch sensor (unlock sensor) ON or OFF ON: Front passenger door touch sensor (unlock sensor) touched
OFF: Front passenger door touch sensor (unlock sensor) not touched
·

Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
P-Door Touch Sensor
50003 125 9
OK:

The intelligent tester display changes correctly in response to the operation of the front door outside handle assembly (for front passenger side).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
a.

Disconnect the V1*1 or W1*2 front door outside handle assembly (for front passenger door) connector.


b.

Disconnect the I78 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

·

*1: for LHD

·

*2: for RHD


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
V1-4 (SENS) - I78-23 (SEN2) Always Below 1 Ω
A43-11 (E) - Body ground Always Below 1 Ω
V1-4 (SENS) or I78-23 (SEN2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
W1-4 (SENS) - I78-23 (SEN2) Always Below 1 Ω
A43-11 (E) - Body ground Always Below 1 Ω
W1-4 (SENS) or I78-23 (SEN2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) (FRONT PASSENGER DOOR UNLOCK SENSOR SIGNAL INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) (FRONT PASSENGER DOOR UNLOCK SENSOR SIGNAL INPUT)
a.

Connect the V1*1 or W1*2 front door outside handle assembly (for front passenger door) connector.

B274842C41
0.919,0.558 1.089,0.714 0.17,0.156 10 *a 4.17,2.786 4.34,2.942 0.17,0.156 10 *1 4.016,3.85 4.366,4.007 0.351,0.156 10 GND 2.769,2.183 2.939,2.339 0.17,0.156 10 E 5.459,2.786 5.629,2.942 0.17,0.156 10 *b 2.06,0.836 2.437,1.069 0.377,0.233 2.133,0.88 2.454,1.043 0.321,0.163 10 A43 4.651,0.836 5.029,1.069 0.377,0.233 4.753,0.88 5.074,1.043 0.321,0.163 10 I78 2.657,1.691 2.79,2.152 false 5.122,2.197 5.544,2.353 0.422,0.156 10 SEN2 5.01,1.705 5.143,2.166 false 5.021,3.272 5.502,2.94 5.502,2.94 5.336,3.276 false
*1 Waveform - -
*a Component with harness connected
(Certification ECU (smart key ECU assembly))
*b In actuality, sampling is being performed


·

*1: for LHD

·

*2: for RHD



b.

Connect the I78 certification ECU (smart key ECU assembly) connector.


c.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
I78-23 (SEN2) - A43-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Front passenger door unlock sensor not touched → touched


2 V/DIV., 500 ms/DIV. Pulse generation (See waveform)



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)