Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM2030EQ _58 Vehicle Interior _014672 HEATING / AIR CONDITIONING _0074651 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1422/22  Compressor Lock Sensor Circuit  


SYSTEM DESCRIPTION

The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication.

The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier assembly determines that the compressor is locked, and turns the magnetic clutch off.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1422/22 Compressor Lock Sensor Circuit Open or short in A/C lock sensor circuit
·

Compressor drive belt

·

Cooler compressor assembly (A/C lock sensor)

·

Harness or connector between cooler compressor assembly (A/C lock sensor) and air conditioning amplifier assembly

·

Air conditioning amplifier assembly

·

CAN communication system


-

WIRING DIAGRAM

E226603
0.677,1.615 1.354,1.979 0.677,0.365 10 false ECM 0.74,3.813 2.823,4.24 2.083,0.427 10 false : CAN Communication Line 5.958,1.885 6.635,2.302 0.677,0.417 10 false LOCK 5.958,3.052 6.729,3.479 0.771,0.427 10 false SG-2 4.177,1.781 4.563,2.135 0.385,0.354 10 false 1 2.844,1.771 3.313,2.177 0.469,0.406 10 false 2 2.646,2.406 4.49,2.75 1.844,0.344 10 false Cooler Compressor Assembly (A/C Lock Sensor) 5.563,3.667 7.115,4.146 1.552,0.479 10 false Air Conditioning Amplifier Assembly 5.708,1.792 5.99,2.135 0.281,0.344 10 false 8 5.677,2.938 6.01,3.271 0.333,0.333 10 false 13 2.646,2.229 3.167,2.5 0.521,0.271 10 false E73 5.563,3.479 5.885,3.813 0.323,0.333 10 false I77 3.729,1.781 4.125,1.938 0.396,0.156 10 false SSR+ 3.021,1.781 3.417,1.938 0.396,0.156 10 false SSR- 0.385,1.615 1.063,1.979 0.677,0.365 10 false A25

PROCEDURE

1.INSPECT COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR)
a.
E167398
1.458,1.167 1.938,1.5 0.479,0.333 1.896,2.156 2.49,2.156 false 1.542,2.167 0.917,2.167 false 0.271,0.167 0.604,0.458 0.333,0.292 10 false *a 1.583,1.24 2.052,1.51 0.469,0.271 10 false E73 2.531,2.063 3.115,2.365 0.583,0.302 10 false SSR+ 0.448,2.063 1.021,2.375 0.573,0.313 10 false SSR-
*a Component without harness connected
(Cooler Compressor Assembly (A/C Lock Sensor))


Disconnect the E73 cooler compressor assembly (A/C lock sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E73-1 (SSR+) - E73-2 (SSR-) 20°C (68°F) 160 to 320 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR))

NG

REPLACE COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR)

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR))
a.

Disconnect the I77 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I77-8 (LOCK) - E73-1 (SSR+) Always Below 1 Ω
I77-13 (SG-2) - E73-2 (SSR-) Always Below 1 Ω
I77-8 (LOCK) - Body ground Always 10 kΩ or higher
I77-13 (SG-2) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY