Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS › 2012.02–2016.05
RM2030EQ _59 Vehicle Exterior _014675 WINDOW / GLASS _0074684 BACK WINDOW GLASS A

WINDOW / GLASS  BACK WINDOW GLASS  REMOVAL  


PROCEDURE

Hide 1.REMOVE ROOF HEADLINING ASSEMBLY

Hide 73370C 2.DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

Hide 73360C 3.DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

Hide 73480 4.DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (for LHD)

Hide 73480 5.DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (for RHD)

Hide 73373 6.REMOVE REAR SEAT SHOULDER BELT COVER

Hide 64330 7.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)

Hide 64330 8.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)

Hide 64811 9.REMOVE BACK WINDOW GLASS SUB-ASSEMBLY

a.

Disconnect each connector.


b.
B280229C06
2.563,0.5 2.844,0.427 false 2.885,0.354 3.083,0.521 0.198,0.167 10 false *1
*1 Protective Tape


Apply protective tape to the area around the installation position of the back window glass on the vehicle body to prevent it from being scratched.

HINT:

Apply protective tape to the vehicle body to prevent it from being scratched.



c.
B280231C06
2.125,0.385 1.74,0.708 1.74,0.708 1.323,0.385 false 1.208,1.5 1.104,1.615 false 1.677,0.74 1.844,0.917 0.167,0.177 10 false *1 0.938,1.542 1.104,1.719 0.167,0.177 10 false *2
*1 Stopper
*2 Piano Wire


Pass a piano wire between the vehicle body and glass from the interior.


d.

Tie both wire ends to wooden blocks or similar objects.


e.

Cut off the adhesive by pulling the piano wire around the back window glass.

NOTICE:

When separating the back window glass, take care not to damage the paint or interior and exterior ornaments.



f.
B280230C15
1.76,0.281 2.052,0.281 2.052,0.281 2.052,0.656 false 1.76,0.563 2.052,0.563 false 2,0.667 2.167,0.844 0.167,0.177 10 false *1
*1 Matchmark


Place matchmarks on the back window glass and vehicle body on the locations indicated in the illustration.

HINT:

Matchmarks are not needed to be placed if the back window glass will not be reused.



g.

Disconnect the back window glass stoppers.

B280233C06
2.167,1 2.281,1.031 false 5.438,0.74 5.563,0.802 false 5.073,0.99 5.073,1.073 5.073,1.073 5.531,1.073 false 5.208,0.885 5.208,1.073 false 5.344,0.885 5.344,1.063 false 3.927,0.49 4.302,0.823 0.375,0.333 12 false *B 0.823,0.479 1.094,0.76 0.271,0.281 12 false *A 2.313,0.958 2.542,1.167 0.229,0.208 10 false *1 5.552,0.99 5.781,1.198 0.229,0.208 10 false *1 5.573,0.729 5.802,0.938 0.229,0.208 10 false *2
*A 1-piece type *B 2-piece type
*1 No. 1 Back Window Glass Stopper *2 No. 2 Back Window Glass Stopper


NOTICE:
·

There are No. 1 and No. 2 stoppers on the back window glass as shown in the illustration. Be careful not to damage the back window glass when cutting off the adhesive.

·

To prevent the back window glass from falling when performing this operation, be sure to hold the back window glass using suction cups.



HINT:

Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.



h.

Using suction cups, remove the back window glass sub-assembly.

NOTICE:
·

Be careful not to drop the back window glass.

·

Leave as much adhesive on the vehicle body as possible when removing the back window glass.




Hide 56117A 10.REMOVE BACK WINDOW GLASS ADHESIVE DAM

a.

When reusing the back window glass:

i.
B280251C06
0.104,0.125 0.406,0.406 0.302,0.281 12 false *A
*A Back Side


Using a scraper, remove the back window glass adhesive dam.

NOTICE:
·

Be careful not to damage the back window glass.

·

Be sure to replace the back window glass adhesive dam with a new one.





Hide 75573F 11.REMOVE BACK WINDOW OUTSIDE MOULDING

a.

When reusing the back window glass:

i.
B280234C06
0.135,0.125 0.427,0.438 0.292,0.313 12 false *A
*A Back Side


Using a scraper, remove the back window outside moulding.

NOTICE:
·

Be careful not to damage the back window glass.

·

Be sure to replace the back window outside moulding with a new one.





Hide 12.REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 1-piece Type)

a.

When reusing the back window glass:

i.
B280235C12
0.135,0.146 0.417,0.375 0.281,0.229 12 false *A
*A Back Side


Using a scraper, remove the 2 No. 1 back window glass stoppers.

NOTICE:
·

Be careful not to damage the back window glass.

·

Be sure to replace the No. 1 back window glass stoppers with new ones.





Hide 56116D 13.REMOVE NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type)

a.

When reusing the back window glass:

i.
B280235C13
0.135,0.125 0.438,0.375 0.302,0.25 12 false *A
*A Back Side


Using a scraper, remove the 2 No. 2 back window glass stoppers.

NOTICE:
·

Be careful not to damage the back window glass.

·

Be sure to replace the No. 2 back window glass stoppers with new ones.





Hide 56115B 14.REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type)

a.
B280236

Remove the 2 No. 1 back window glass stoppers.

NOTICE:

Be sure to replace the No. 1 back window glass stoppers with new ones.



Hide 15.CLEAN BACK WINDOW GLASS

a.

Using a scraper, remove any adhesive dam and adhesive residue from the back window glass.

NOTICE:

Be careful not to damage the back window glass.



b.
B187131

Clean the outer circumference of the back window glass with a non-residue solvent.

NOTICE:
·

Do not touch the glass surface after cleaning it.

·

Be careful not to damage the glass.

·

Even if using new glass, clean it with a non-residue solvent.




Hide 16. CLEAN VEHICLE BODY

a.
B149737C27
2.313,1.542 2.438,1.667 false 0.865,1.521 1,1.646 false 0.958,0.677 0.844,0.49 0.844,0.49 0.635,0.49 false 2.531,0.677 2.604,0.74 2.604,0.74 2.74,0.74 false 0.938,1.646 1.167,1.802 0.229,0.156 10 false *1 2.396,1.698 2.625,1.854 0.229,0.156 10 false *1 0.448,0.417 0.677,0.573 0.229,0.156 10 false *2 2.781,0.656 3.01,0.813 0.229,0.156 10 false *2
*1 Adhesive
*2 Body


Clean and shape the contact surface of the vehicle body.

i.

Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.