Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING › 2012.02–2015.04
RM2030EQ _59 Vehicle Exterior _014676 SLIDING ROOF / CONVERTIBLE _0074685 SLIDING ROOF HOUSING A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING  INSTALLATION  


PROCEDURE

Hide 1.INSTALL SLIDING ROOF HOUSING ASSEMBLY

a.

Loosen the 4 bolts from the sliding roof housing assembly.


b.

Install the sliding roof housing assembly with the 4 bolts and 8 nuts.

Torque:
Nut : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Be careful not to damage the vehicle body.



c.

Tighten the 4 bolts to the sliding roof housing assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.
B280751C02
2.833,1.177 3.417,0.885 false 2.938,1.604 3.094,1.635 false 2.646,1.385 2.802,1.5 false 2.479,1.302 2.635,1.448 0.156,0.146 10 *2 3.135,1.552 3.292,1.698 0.156,0.146 10 *1
*1 Clip
*2 Marking


for Clamp Type:

i.

Insert the sliding roof drain hose.

HINT:

The hose should be inserted to the base of the drain pipe.



ii.

Engage the claw to connect the sliding roof drain hose.

HINT:
·

Make sure that the clamp is on the marking or between the marking and hose end.

·

Use the same procedure for the other 3 sliding roof drain hoses.





e.
B280752C03
2.719,1.49 2.542,1.375 false 2.802,1.615 3.073,1.646 false 3.115,1.542 3.271,1.688 0.156,0.146 10 false *1 2.396,1.281 2.552,1.427 0.156,0.146 10 false *2 2.552,2.427 2.708,2.573 0.156,0.146 10 false *b 0.552,4.313 0.708,4.458 0.156,0.146 10 false *a
*1 Clip
*2 Marking
*a Front Side
*b Outside


for Clip Type:

i.

Expand the clip to insert the sliding roof drain hose.

HINT:

The hose should be inserted to the base of the drain pipe.



ii.

Release the clip to connect the sliding roof drain hose.

NOTICE:

The clip must face toward the outside of the vehicle and also be above the lower surface of the sliding roof housing when installing the drain hoses.


HINT:
·

Make sure that the clip is on the marking or between the marking and hose end.

·

Use the same procedure for the other 3 sliding roof drain hoses.





Hide 66425B 2.INSTALL REAR NO. 2 SIDE RAIL SPACER LH

a.
B279107

Engage the 2 claws to install the rear No. 2 side rail spacer LH.


Hide 66415B 3.INSTALL REAR NO. 2 SIDE RAIL SPACER RH

HINT:

Use the same procedure as for the LH side.


Hide 62180A 4.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

Hide 62170A 5.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 63251H 6.INSTALL SLIDING ROOF WEATHERSTRIP

a.

Install the sliding roof weatherstrip as follows:

i.

Position the joint of the weatherstrip at the rear center.


ii.

Align the alignment mark (yellow) on the weatherstrip with the middle marks at the corners of the sliding roof panel sub-assembly and install the weatherstrip.


iii.

Install the lip of the weatherstrip firmly.

B279127C03
1.979,2.031 2.115,1.698 2.115,1.698 2.24,1.698 false 4.5,2.188 4.573,2.031 4.573,2.031 4.677,2.031 false 5.615,2.229 5.688,2.063 5.688,2.063 5.781,2.063 false 6.656,2.167 6.729,2 6.729,2 6.823,2 false 3.146,3.177 3.063,3.354 false 3.083,3.104 3.333,3.073 false 3.948,0.573 4.146,0.74 0.198,0.167 12 *A 3.948,1.927 4.146,2.094 0.198,0.167 12 *B 1.906,2.583 2.063,2.729 0.156,0.146 10 *2 3.354,3 3.51,3.146 0.156,0.146 10 *4 2.99,3.365 3.146,3.51 0.156,0.146 10 *3 2.26,1.625 2.417,1.771 0.156,0.146 10 *1 5.802,1.979 5.958,2.125 0.156,0.146 10 *b 6.854,1.896 7.01,2.042 0.156,0.146 10 *c 4.719,1.927 4.875,2.073 0.156,0.146 10 *a
*A Normal *B Abnormal
*1 Joint *2 Rear
*3 Alignment Mark (Yellow) *4 Middle Mark
*a Pinched *b Exposed
*c Gap (raised, wavy, etc.) - -




Hide 63201G 7.INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY

a.

Using a T25 "TORX" socket wrench, temporarily install the sliding roof glass sub-assembly with the 4 screws.


b.

Perform a level check.

B233685E02
2.198,2.115 2.313,2.26 0.115,0.146 10 B 2.469,2.115 2.583,2.26 0.115,0.146 10 B 1.74,1.094 1.865,1.24 0.125,0.146 10 C 1.74,1.354 1.865,1.5 0.125,0.146 10 C 2.104,2.698 2.229,2.844 0.125,0.146 10 D 1.5,2.104 1.615,2.25 0.115,0.146 10 A 1.771,2.104 1.885,2.25 0.115,0.146 10 A 1.969,2.354 2.094,2.5 0.125,0.146 10 D 4.896,1.479 5.021,1.625 0.125,0.146 10 a

i.

Check the difference in level for "a" between the roof panel and the upper surface of the weatherstrip when the sliding roof glass is fully closed.

Standard:
Area Measurement
A - A 0 + 1.0 mm (0 + 0.0394 in.)
0 - 2.0 mm (0 - 0.0787 in.)
B - B 0 + 2.0 mm (0 + 0.0787 in.)
0 - 1.0 mm (0 - 0.0394 in.)
C - C 0 + 1.5 mm (0 + 0.0591 in.)
0 - 1.5 mm (0 - 0.0591 in.)
D - D 0 + 1.5 mm (0 + 0.0591 in.)
0 - 1.0 mm (0 - 0.0394 in.)


HINT:

"+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.




c.
B122200C03
0.833,1.188 0.99,1.479 0.156,0.292 10 false *a
*a Even


Perform a gap check.

i.

Check the gap between the roof panel and roof glass.

NOTICE:

The width must be even all around.




d.
B279110

After adjusting the sliding roof glass, using a T25 "TORX" socket wrench, install the sliding roof glass sub-assembly with the 4 screws.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 8. CHECK FOR WATER LEAK

a.

After adjusting the sliding roof glass sub-assembly, check for water leakage into the vehicle interior.


b.

If there are any leaks, readjust the sliding roof glass sub-assembly.


Hide 63218G 9.INSTALL SLIDING ROOF SIDE GARNISH LH

a.

Engage the 2 claws to install a new sliding roof side garnish LH.


Hide 63217G 10.INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 11.INSTALL ROOF HEADLINING ASSEMBLY

Hide 12.RESET SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY