The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH, curtain shield airbag assembly RH and front seat outer belt assembly RH) is composed of the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.
The side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag and pretensioner should be deployed.
These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1622/81 | Lost communication with Side Airbag Sensor RH | ·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit. ·
Side airbag sensor assembly RH malfunction ·
Side No. 2 airbag sensor assembly RH malfunction ·
Airbag sensor assembly malfunction |
·
No. 2 floor wire ·
Side airbag sensor assembly RH ·
Side No. 2 airbag sensor assembly RH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| B1623/81 | Side Airbag Sensor Assembly RH Initialization Incomplete | ·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit. ·
Side airbag sensor assembly RH malfunction ·
Side No. 2 airbag sensor assembly RH malfunction ·
Airbag sensor assembly malfunction |
·
No. 2 floor wire ·
Side airbag sensor assembly RH ·
Side No. 2 airbag sensor assembly RH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| B1632/81 | Lost Communication with Rear Airbag Sensor RH | ·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit. ·
Side airbag sensor assembly RH malfunction ·
Side No. 2 airbag sensor assembly RH malfunction ·
Airbag sensor assembly malfunction |
·
No. 2 floor wire ·
Side airbag sensor assembly RH ·
Side No. 2 airbag sensor assembly RH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| B1633/81 | Rear Airbag Sensor Assembly RH Initialization Incomplete | ·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit. ·
Side airbag sensor assembly RH malfunction ·
Side No. 2 airbag sensor assembly RH malfunction ·
Airbag sensor assembly malfunction |
·
No. 2 floor wire ·
Side airbag sensor assembly RH ·
Side No. 2 airbag sensor assembly RH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| B1642/81 | Lost Communication with Side Satellite Sensor Bus RH | ·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit. ·
Side airbag sensor assembly RH malfunction ·
Side No. 2 airbag sensor assembly RH malfunction ·
Airbag sensor assembly malfunction |
·
No. 2 floor wire ·
Side airbag sensor assembly RH ·
Side No. 2 airbag sensor assembly RH ·
Airbag sensor assembly |
Does not apply to test/check mode |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Check for current DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then to ON again.
Codes other than current DTCs B1622, B1623, B1632, B1633, B1642 and 81 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| Current DTC B1642 or 81 is output. | A |
| Current DTC B1623 is output. | B |
| Current DTC B1632 or B1633 is output. | C |
| Current DTC B1622 is output. | D |
| Current DTCs B1622, B1623, B1632, B1633, B1642 and 81 are not output. | E |
A
B
C
D
E
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.
The connectors are properly connected.
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.
Check that the terminals of the connectors are not damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-4 (BBR+) - O11-3 (BBR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-4 (BBR+) - O11-3 (BBR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-4 (BBR+) - Body ground | Ignition switch ON | Below 1 V |
| O11-3 (BBR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| O11-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH) |
Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-1 (BCR+) - O11-2 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-1 (BCR+) - O11-2 (BCR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| O11-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| O11-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the side No. 2 airbag sensor assembly RH and airbag sensor assembly.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B1642 or 81 is output. | A |
| DTC B1647 or 82 is output. | B |
| DTCs B1642, B1647, 81 and 82 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly RH |
Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTCs B1642, B1647, 81 and 82 are not output. | A |
| DTC B1642 or 81 is output. | B |
| DTC B1647 or 82 is output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Check for history DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than history DTC B1622 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| History DTC B1622 is not output. | A |
| History DTC B1622 is output. | B |
A
B
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly and side airbag sensor assembly RH.
The connectors are properly connected.
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag sensor assembly and side airbag sensor assembly RH.
Check that the terminals of the connectors are not damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-4 (BBR+) - O11-3 (BBR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-4 (BBR+) - O11-3 (BBR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-4 (BBR+) - Body ground | Ignition switch ON | Below 1 V |
| O11-3 (BBR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| O11-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
Connect the connector to the airbag sensor assembly.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTCs B1623 and B1628 are not output. | A |
| DTC B1623 is output. | B |
| DTC B1628 is output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTCs B1622 and B1627 are not output. | A |
| DTC B1622 is output. | B |
| DTC B1627 is output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.
The connectors are properly connected.
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.
Check that the terminals of the connectors are not damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH) |
Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-1 (BCR+) - O11-2 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-1 (BCR+) - O11-2 (BCR-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| O11-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O11-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| O11-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
Connect the connector to the side No. 2 airbag sensor assembly RH.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B1632 or B1633 is output. | A |
| DTC B1637 or B1638 is output. | B |
| DTCs B1632, B1633, B1637 and B1638 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly RH |
Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTCs B1632, B1633, B1637 and B1638 are not output. | A |
| DTC B1632 or B1633 is output. | B |
| DTC B1637 or B1638 is output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTCs B1622 and B1627 are not output. | A |
| DTC B1622 is output. | B |
| DTC B1627 is output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C