The front passenger side squib circuit consists of the airbag sensor assembly and instrument panel passenger airbag assembly.
The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1805/52 | Short in Front Passenger Side Squib Circuit | ·
The airbag sensor assembly receives a line short circuit signal in the front passenger side squib circuit during primary check. ·
Front passenger side squib malfunction ·
Airbag sensor assembly malfunction |
·
Instrument panel wire ·
No. 2 instrument panel wire ·
Instrument panel passenger airbag assembly (Front passenger side squib) ·
Airbag sensor assembly |
Applies to check mode |
| B1806/52 | Open in Front Passenger Side Squib Circuit | ·
The airbag sensor assembly receives an open circuit signal in the front passenger side squib circuit. ·
Front passenger side squib malfunction ·
Airbag sensor assembly malfunction |
·
Instrument panel wire ·
No. 2 instrument panel wire ·
Instrument panel passenger airbag assembly (Front passenger side squib) ·
Airbag sensor assembly |
Applies to check mode |
| B1807/52 | Short to GND in Front Passenger Side Squib Circuit | ·
The airbag sensor assembly receives a short circuit to ground signal in the front passenger side squib circuit. ·
Front passenger side squib malfunction ·
Airbag sensor assembly malfunction |
·
Instrument panel wire ·
No. 2 instrument panel wire ·
Instrument panel passenger airbag assembly (Front passenger side squib) ·
Airbag sensor assembly |
Applies to check mode |
| B1808/52 | Short to B+ in Front Passenger Side Squib Circuit | ·
The airbag sensor assembly receives a short circuit to B+ signal in the front passenger side squib circuit. ·
Front passenger side squib malfunction ·
Airbag sensor assembly malfunction |
·
Instrument panel wire ·
No. 2 instrument panel wire ·
Instrument panel passenger airbag assembly (Front passenger side squib) ·
Airbag sensor assembly |
Applies to check mode |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Instrument Panel Passenger Airbag Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Instrument Panel Wire |
| *4 | Instrument Panel Wire |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the instrument panel passenger airbag assembly and airbag sensor assembly. Also check that the connectors that link the instrument panel wire and No. 2 instrument panel wire are properly connected.
The connectors are properly connected.
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the instrument panel passenger airbag assembly and airbag sensor assembly. Also disconnect the instrument panel wire from the No. 2 instrument panel wire.
Check that the terminals of the connectors are not damaged.
The terminals are not deformed or damaged.
Check that the No. 2 instrument panel wire connector (on the instrument panel passenger airbag assembly side) is not damaged.
The lock button is not disengaged, or the claw of the lock is not deformed or damaged.
Check that the short springs for the instrument panel wire and No. 2 instrument panel wire with the activation prevention mechanism are not deformed or damaged.
The short springs are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Instrument Panel Passenger Airbag Assembly |
| *2 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly) |
Connect the instrument panel wire to the No. 2 instrument panel wire and airbag sensor assembly.
Connect SST (resistance 2.1 Ω) to connector E.
Never connect the tester to the instrument panel passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting it.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.
Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Disconnect SST from connector E.
OK
NG
| *1 | Instrument Panel Passenger Airbag Assembly |
| *2 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly) |
Disconnect the instrument panel wire from the airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b1-2 (P+) - Body ground | Ignition switch ON | Below 1 V |
| b1-1 (P-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b1-2 (P+) - b1-1 (P-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b1-2 (P+) - Body ground | Always | 1 MΩ or higher |
| b1-1 (P-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b1-2 (P+) - b1-1 (P-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Instrument Panel Passenger Airbag Assembly |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the instrument panel passenger airbag assembly and airbag sensor assembly.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.
Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *1 | Instrument Panel Passenger Airbag Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Instrument Panel Wire |
| *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to No. 2 Instrument Panel Wire) |
Disconnect the No. 2 instrument panel wire from the instrument panel wire.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Ib1-1 (P+) - Body ground | Ignition switch ON | Below 1 V |
| Ib1-2 (P-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Ib1-1 (P+) - Ib1-2 (P-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Ib1-1 (P+) - Body ground | Always | 1 MΩ or higher |
| Ib1-2 (P-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Ib1-1 (P+) - Ib1-2 (P-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Instrument Panel Passenger Airbag Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Instrument Panel Wire |
| *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly) |
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b1-2 (P+) - Body ground | Ignition switch ON | Below 1 V |
| b1-1 (P-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b1-2 (P+) - b1-1 (P-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b1-2 (P+) - Body ground | Always | 1 MΩ or higher |
| b1-1 (P-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector D.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b1-2 (P+) - b1-1 (P-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector D to the original condition.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG