Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › 2012.02–2015.04
RM2030EQ _56 Audio / Visual / Telematics _014660 PARK ASSIST / MONITORING _0076659 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Clearance Sonar Main Switch Circuit  


DESCRIPTION

The back sonar or clearance sonar switch assembly is installed at the base of the driver side of the instrument panel.

When the clearance sonar main switch is turned on, an on signal is sent to the clearance warning ECU assembly. The Toyota parking assist-sensor system operates according to this signal.

WIRING DIAGRAM

E222388E34
5.51,1.49 6.698,1.979 1.188,0.49 10 false Clearance Warning ECU Assembly 3.219,1.198 5.167,1.594 1.948,0.396 10 false Back Sonar or Clearance Sonar Switch Assembly 5.552,0.625 6.146,0.833 0.594,0.208 10 false CLSW 5.5,1.333 6.094,1.542 0.594,0.208 10 false I82 3.229,1.01 3.948,1.24 0.719,0.229 10 false I5*1, I6*2 2.063,0.906 3.125,1.115 1.063,0.208 10 false ECU-IG1 NO. 2 0.302,0.604 1.823,0.948 1.521,0.344 10 false from IG1 NO. 2 Relay 4.573,0.521 4.802,0.719 0.229,0.198 10 false 6 3.365,0.521 3.583,0.792 0.219,0.271 10 false 9 5.333,0.5 5.688,0.844 0.354,0.344 10 false 9 3.552,0.531 3.854,0.76 0.302,0.229 10 false IG 4.188,0.531 4.698,0.76 0.51,0.229 10 false ECU 3.208,1.531 5.167,1.833 1.958,0.302 10 false (Clearance Sonar Main Switch) 4.552,2.063 5.271,2.292 0.719,0.229 10 false *1: for LHD 4.563,2.406 5.281,2.635 0.719,0.229 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Clearance Sonar / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Clearance Sonar > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main Switch Clearance sonar main switch OFF or ON OFF: Clearance sonar main switch off
ON: Clearance sonar main switch on
-
Clearance Sonar ECU Type Type of clearance sonar ECU Normal Normal: Normal clearance sonar type -
Body Electrical > Clearance Sonar > Data List
Tester Display
Main Switch
Clearance Sonar ECU Type
50003 170 1,4

Result:
Result Proceed to
Both of the following conditions are met:
·

The display changes as shown above when the clearance sonar main switch is operated.

·

"Normal" is displayed.


A
"Normal" is not displayed. B
Both of the following conditions are met:
·

The display does not change as shown above when the clearance sonar main switch is operated.

·

"Normal" is displayed.


C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

C

2.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
2.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
a.

Remove the back sonar or clearance sonar switch assembly.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>REMOVAL


b.
E197324C05
1.573,1.385 1.573,1.625 1.573,1.625 1.063,1.625 false 2.021,1.385 2.021,1.625 2.021,1.625 2.531,1.625 false 0.823,1.531 1.26,1.844 0.438,0.313 10 IG 2.573,1.531 3.094,1.854 0.521,0.323 10 ECU 0.115,0.063 0.635,0.417 0.521,0.354 10 *a
*a Component without harness connected
(Back Sonar or Clearance Sonar Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (IG) - 6 (ECU) Clearance sonar main switch on Below 1 Ω
9 (IG) - 6 (ECU) Clearance sonar main switch off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY POWER SOURCE)

NG

REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY POWER SOURCE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
I5-9 (IG) - Body ground Engine switch on (IG) 11 to 14 V
I5-9 (IG) - Body ground Engine switch off Below 1 V

for RHD
Tester Connection Condition Specified Condition
I6-9 (IG) - Body ground Engine switch on (IG) 11 to 14 V
I6-9 (IG) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the I82 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I82-9 (CLSW) - I5-6 (ECU) Always Below 1 Ω
I82-9 (CLSW) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
I82-9 (CLSW) - I6-6 (ECU) Always Below 1 Ω
I82-9 (CLSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR