Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM2030EQ _58 Vehicle Interior _014667 METER / GAUGE / DISPLAY _0074615 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

The meter ECU receives vehicle speed signal from the skid control ECU via the CAN communication system. The speed sensors detect the wheel speed and send signals to the skid control ECU. The skid control ECU supplies power to the vehicle speed sensors. The skid control ECU creates the vehicle speed signal based on the pulses of the voltage.

HINT:
·

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using the intelligent tester. For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION

·

If the vehicle speed sensor circuit has a malfunction, the skid control ECU stores DTCs. Troubleshoot the vehicle stability control system.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR



WIRING DIAGRAM

E143765E84
0.25,3.104 1.438,3.313 1.188,0.208 10 Skid Control ECU 2.917,3.167 3.01,3.354 0.094,0.188 10 : 2.969,3.177 4.719,3.521 1.75,0.344 10 CAN Communication Line 5.302,3.104 7.146,3.417 1.844,0.313 10 Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


HINT:

Before starting the following inspection, check tire size and tire air pressure.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SPEED METER OPERATION)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SPEED METER OPERATION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Speed Meter Operation Speedometer 0, 40, 80, 120, 160, 200, 240 km/h -
Body Electrical > Combination Meter > Active Test
Tester Display
Speed Meter Operation
50004 122 1
OK:

Speedometer indication is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK VEHICLE STABILITY CONTROL SYSTEM

NG

REPLACE COMBINATION METER ASSEMBLY

3.CHECK VEHICLE STABILITY CONTROL SYSTEM
a.

Check if vehicle stability control system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

4.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED, VEHICLE SPEED METER)

B

4.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED, VEHICLE SPEED METER)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus:

i.

for ABS/VSC/TRC: Chassis / ABS/VSC/TRC / Data List.


ii.

for Combination Meter: Body / Combination Meter / Data List.



e.

Check the values by referring to the table below.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost the same as actual vehicle speed -
Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Body Electrical > Combination Meter > Data List
Tester Display
Vehicle Speed Meter
50003 122 8
Chassis > ABS/VSC/TRC > Data List
Tester Display
Vehicle Speed
50003 105 42

Result:
Result Proceed to
The data list values of the ECUs match. A
The data list values of the ECUs do not match. B


HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.

·

When the Data List values of the ECUs do not match, a signal output error of the skid control ECU or an internal malfunction of the combination meter assembly is suspected.




A

REPLACE COMBINATION METER ASSEMBLY

B

5.REPLACE COMBINATION METER ASSEMBLY
5.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new or a known good one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


Result:
Result Proceed to
The operation of the speedometer returns to normal. A
The operation of the speedometer does not return to normal. B



A

END

B