Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2030EQ _54 Brake _014650 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0077110 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1426  Stop Light Switch OFF Stuck Malfunction  


DESCRIPTION

The skid control ECU receives stop light switch signals and uses them to determine whether or not the brakes are applied.

The skid control ECU has a detection circuit that it uses to detect a short in the stop light input line, or the ground line of the stop light circuit with the stop light switch on (brake pedal depressed).

If the skid control ECU detects a short in this circuit, it will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1426 Stop Light Switch OFF Stuck Malfunction Either of the following is detected:
1.

With the stop light switch off, the stop light switch is judged to be on based on the master cylinder pressure value for 3 seconds or more.

2.

With the stop light switch off, the master cylinder pressure is more than 8 MPa (81.6 kgf/cm2, 1160 psi) for 3 seconds or more.


·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Ground circuit

·

Skid control ECU (Brake actuator assembly)



PROCEDURE

1.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the brake pedal height and stop light switch assembly installation.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for RHD)>ADJUSTMENT

OK:

The brake pedal height and stop light switch assembly installation are normal.


HINT:

If the on/off status of the stop light switch assembly and the pressure increase information from the master cylinder pressure sensor do not match due to an improperly installed brake pedal or stop light switch assembly, this DTC may be stored. Therefore, be sure to check the installation condition of the pedal and switch before inspecting the input signals and other related parts.



Result:
Result Proceed to
OK A
NG(for LHD) B
NG(for RHD) C



A

2.CHECK STOP LIGHT OPERATION

B

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

C

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

2.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. ON
Brake pedal released. OFF



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

d.

Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.

OK:

The intelligent tester displays on or off according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
4.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1426 is not output. A
DTC C1426 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C238832C22
0.208,0.719 0.688,1.042 0.479,0.323 1.542,1.521 2.188,0.792 false 0.271,0.198 0.469,0.354 0.198,0.156 10 *a 0.333,0.802 0.917,1.146 0.583,0.344 10 A49 2.083,0.594 2.521,0.823 0.438,0.229 10 STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A49 skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-30 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V*


HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C238832C23
0.208,0.719 0.688,1.042 0.479,0.323 2.823,1.5 2.219,0.75 false 0.271,0.198 0.615,0.646 0.344,0.448 10 *a 0.344,0.802 0.75,1.094 0.406,0.292 10 A49 1.948,0.563 2.385,0.719 0.438,0.156 10 GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-38 (GND1) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C173882C05
0.365,0.979 0.833,1.302 0.469,0.323 0.333,0.25 0.656,0.656 0.323,0.406 10 *a 0.49,1.063 1.063,1.594 0.573,0.531 10 A33
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Check that the STOP (7.5 A) fuse is normal.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A33 stop light switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A33-2 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

8.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
C239673C05
0.338,0.37 0.564,0.54 0.226,0.17 10 *a 1.941,1.855 2.415,1.068 false 1.659,1.855 1.184,1.068 false 2.401,0.851 2.571,1.021 0.17,0.17 10 1 1.077,0.851 1.233,1.021 0.156,0.17 10 2
*a Component without harness connected
(Stop Light Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch pin free Below 1 Ω
1 - 2 Switch pin pushed in 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C238832C22
0.208,0.719 0.688,1.042 0.479,0.323 1.542,1.521 2.188,0.792 false 0.271,0.198 0.469,0.354 0.198,0.156 10 *a 0.333,0.802 0.917,1.146 0.583,0.344 10 A49 2.083,0.594 2.521,0.823 0.438,0.229 10 STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Reconnect the A33 stop light switch assembly connector.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A49 skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-30 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V*
A49-30 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V


HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

10.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

10.RECONFIRM DTC
a.

Reconnect the A49 skid control ECU connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1426 is not output. A
DTC C1426 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

B