Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2030EQ _54 Brake _014650 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0077110 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU receives stop light switch signals and uses them to determine whether or not the brakes are applied.

The skid control ECU has a detection circuit that it uses to detect an open in the stop light input line.

If the skid control ECU detects an open in this circuit, it will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1425 Open in Stop Light Switch Circuit An open in the stop light switch input line continues for 3 seconds or more.
·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Skid control ECU (Brake actuator assembly)



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. ON
Brake pedal released. OFF



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

d.

Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.

OK:

The intelligent tester displays on or off according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1425 is not output. A
DTC C1425 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

4.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C238832C21
0.208,0.719 0.688,1.042 0.479,0.323 1.531,1.51 2.188,0.792 false 0.302,0.198 0.573,0.531 0.271,0.333 10 *a 0.344,0.802 0.75,1.031 0.406,0.229 10 A49 2.125,0.594 2.531,0.927 0.406,0.333 10 STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A49 skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-30 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V*
A49-30 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V


HINT:
·

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C173882C04
0.365,0.979 0.833,1.302 0.469,0.323 0.333,0.25 0.813,0.813 0.479,0.563 10 *a 0.5,1.063 1.021,1.49 0.521,0.427 10 A33
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Check that the STOP (7.5 A) fuse is normal.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A33 stop light switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A33-2 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
C239673C04
0.338,0.37 0.564,0.54 0.226,0.17 10 *a 1.941,1.855 2.415,1.068 false 1.659,1.855 1.184,1.068 false 2.401,0.851 2.571,1.021 0.17,0.17 10 1 1.077,0.851 1.233,1.021 0.156,0.17 10 2
*a Component without harness connected
(Stop Light Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch pin free Below 1 Ω
1 - 2 Switch pin pushed in 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C238832C20
0.208,0.719 0.688,1.042 0.479,0.323 1.542,1.521 2.188,0.792 false 0.271,0.198 0.646,0.542 0.375,0.344 10 *a 0.323,0.802 0.771,1.156 0.448,0.354 10 A49 2.094,0.594 2.438,0.823 0.344,0.229 10 STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Reconnect the A33 stop light switch assembly connector.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A49 skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-30 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V*
A49-30 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V


HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

8.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

8.RECONFIRM DTC
a.

Reconnect the A49 skid control ECU connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1425 is not output. A
DTC C1425 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

B