Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2030EQ _54 Brake _014650 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0077110 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C146E  Open in ABS Solenoid Relay Circuit  


DESCRIPTION

The ABS solenoid relay is built into the skid control ECU in the brake actuator assembly.

The ABS solenoid relay supplies power to the ABS and TRC solenoids.

The skid control ECU detects a solenoid relay malfunction by performing a self check and relay operation check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C146E Open in ABS Solenoid Relay Circuit Either of the following is detected:
1.

A solenoid relay drive circuit in the skid control ECU is malfunctioning.

2.

The solenoid relay cannot be switched between on and off.


·

ABS NO. 2 fuse (Fusible link block assembly)

·

ABS solenoid relay circuit

·

ABS solenoid relay (Brake actuator assembly)



WIRING DIAGRAM

C250686E03
1.604,1.375 2.604,1.698 1,0.323 10 false ABS NO. 2 4.396,8.229 4.875,8.563 0.479,0.333 10 false A49 3.26,1.094 3.646,1.354 0.385,0.26 10 false 25 3.26,4.979 3.656,5.26 0.396,0.281 10 false 38 0.708,6.865 1.5,7.156 0.792,0.292 10 false Battery 3.531,5.188 4.229,5.542 0.698,0.354 10 false GND1 3.521,1.333 4.042,1.563 0.521,0.229 10 false +BS 4.458,4.302 5.604,4.479 1.146,0.177 10 false Skid Control ECU 4.385,8.385 6.135,8.688 1.75,0.302 10 false Brake Actuator Assembly 4.583,1.01 5.5,1.458 0.917,0.448 10 false ABS Solenoid Relay 5.958,2.177 6.49,2.5 0.531,0.323 10 false SFRH 5.958,2.688 6.542,3.021 0.583,0.333 10 false SFLH 5.958,3.198 6.615,3.49 0.656,0.292 10 false SRRH 5.958,3.688 6.635,4.073 0.677,0.385 10 false SRLH 5.958,4.188 6.531,4.521 0.573,0.333 10 false SFRR 5.958,4.677 6.563,4.938 0.604,0.26 10 false SFLR 5.958,5.177 6.604,5.438 0.646,0.26 10 false SRRR 5.958,5.667 6.51,5.958 0.552,0.292 10 false SRLR 5.958,6.167 6.521,6.448 0.563,0.281 10 false SRM1 5.958,6.667 6.656,7 0.698,0.333 10 false SRM2 5.958,7.177 6.583,7.448 0.625,0.271 10 false SRC1 5.958,7.646 6.5,7.927 0.542,0.281 10 false SRC2 0.635,3.958 1.521,4.26 0.885,0.302 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

When C1241 and/or C1417 is output together with C146E, inspect and repair the trouble areas indicated by C1241 and/or C1417 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1241

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1417


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)
a.
C238832C28
0.208,0.719 0.688,1.042 0.479,0.323 0.76,1.5 1.365,0.75 false 0.271,0.198 0.625,0.542 0.354,0.344 10 *a 0.333,0.802 0.802,1.198 0.469,0.396 10 A49 1.26,0.563 1.625,0.906 0.365,0.344 10 +BS
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A49 skid control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-25 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C238832C29
0.208,0.719 0.688,1.042 0.479,0.323 2.823,1.5 2.219,0.75 false 0.271,0.198 0.583,0.521 0.313,0.323 10 *a 0.333,0.802 0.854,1.094 0.521,0.292 10 A49 1.948,0.563 2.583,0.865 0.635,0.302 10 GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-38 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

3.RECONFIRM DTC
HINT:

This DTC is stored when a problem is identified in the brake actuator assembly.

The solenoid circuits are located in the brake actuator assembly.

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if the DTC is output again before replacing the brake actuator assembly.


a.

Reconnect the A49 skid control ECU connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C146E is not output. A
DTC C146E is output. B


HINT:
·

The skid control ECU performs self diagnosis of the solenoid circuit after the ignition switch is turned to ON.

·

If the normal system code is output (No DTCs are output), slightly jiggle the connectors, wire harnesses, and fuses of the brake actuator assembly.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.





A

B