The No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side) to any position. As a result, the amount of air passing through the heater core after passing through the evaporator is adjusted, and the temperature of the air blowing toward the driver seat side is controlled.
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.
The No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side) to any position. As a result, the amount of air passing through the heater core after passing through the evaporator is adjusted, and the temperature of the air blowing toward the driver seat side is controlled.
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1446/46 | Air Mix Damper Control Servo Motor Circuit (Driver Side) | for LHD:
Air mix damper position sensor value does not change even if air conditioning amplifier assembly operates No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side) for RHD: Air mix damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side) |
·
No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side)*2 ·
No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side)*3 ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
Memorized
(30 sec. or more)*1 |
*1: The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the brackets.
*2: for LHD
*3: for RHD
Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Operate the driver side temperature adjustment switch.
Enter the following menus: Body / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Air Mix Servo Actual Pulse(D) | No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side) actual pulse | Min.: 0, Max.: 255 | MAX COLD: 5 (pulse)
MAX HOT: 103 (pulse) |
- |
| Tester Display |
|---|
| Air Mix Servo Actual Pulse(D) |
The display is as specified in the normal condition column.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (When troubleshooting according to Problem Symptoms Table) | B |
| OK (When troubleshooting according to the DTC) | C |
A
B
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>PROBLEM SYMPTOMS TABLE
C
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Active Test.
Check the operation by referring to the table below.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Air Mix Servo Targ Pulse(D) | No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side) pulse | Min.: 0, Max.: 255 | Operates between 5 and 103 pulses |
| Tester Display |
|---|
| Air Mix Servo Targ Pulse(D) |
Air temperature changes in accordance with each control range.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 2 air conditioning radiator damper servo sub-assembly (air mix for driver side).
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1446/46 is output | A |
| DTC B1446/46 is not output | B |
A
B
Replace the air conditioning harness assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1446/46 is output | A |
| DTC B1446/46 is not output | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Operate the driver side temperature adjustment switch.
Enter the following menus: Body / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Air Mix Servo Actual Pulse(D) | No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side) actual pulse | Min.: 0, Max.: 255 | MAX COLD: 105
MAX HOT: 7 |
- |
| Tester Display |
|---|
| Air Mix Servo Actual Pulse(D) |
The display is as specified in the normal condition column.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (When troubleshooting according to Problem Symptoms Table) | B |
| OK (When troubleshooting according to the DTC) | C |
A
B
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>PROBLEM SYMPTOMS TABLE
C
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Active Test.
Check the operation by referring to the table below.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Air Mix Servo Targ Pulse(D) | No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side) pulse | Min.: 0, Max.: 255 | Operates between 7 and 105 pulses |
| Tester Display |
|---|
| Air Mix Servo Targ Pulse(D) |
Air temperature changes in accordance with each control range.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix for driver side).
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1446/46 is output | A |
| DTC B1446/46 is not output | B |
A
B
Replace the air conditioning harness assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY
Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.
Check for the DTC.
| Result | Proceed to |
|---|---|
| DTC B1446/46 is output | A |
| DTC B1446/46 is not output | B |
A
B