Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.02–2015.04
RM2030EQ _56 Audio / Visual / Telematics _014659 NAVIGATION / MULTI INFO DISPLAY _0074553 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Mute Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Due to this, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E226158E15
1.229,1.094 1.667,1.26 0.438,0.167 10 false MUTE 5.531,1.115 6.115,1.469 0.583,0.354 10 false MUT2 1.74,1.021 1.885,1.156 0.146,0.135 10 false 1 5.271,1.01 5.542,1.219 0.271,0.208 10 false 20 0.542,1.906 1.094,2.229 0.552,0.323 10 false I69 0.531,2.073 1.74,2.5 1.208,0.427 10 false Stereo Component Amplifier Assembly 5.302,1.948 5.615,2.135 0.313,0.188 10 false I67 5.323,2.104 6.323,2.458 1,0.354 10 false Navigation ECU Sub-assembly

PROCEDURE

1.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
E225824C09
0.207,0.166 0.366,0.329 0.16,0.163 10 *a 1.491,0.796 1.954,1.081 0.463,0.286 1.605,0.849 1.846,1.012 0.242,0.163 10 I69 2.699,2.413 3.129,2.576 0.431,0.163 10 MUTE 2.399,1.887 2.861,2.381 false
*a Component with harness connected
(Stereo Component Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I69-1 (MUTE) - Body ground Ignition switch ACC, audio system playing→ Changing modes Above 3.5 V→ Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the navigation ECU sub-assembly connector.


b.

Disconnect the stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I67-20 (MUT2) - I69-1 (MUTE) Always Below 1 Ω
I67-20 (MUT2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
a.
E221772C04
1.497,0.615 1.96,0.901 0.463,0.286 1.614,0.672 1.956,0.828 0.342,0.156 10 I67 0.181,0.157 0.336,0.313 0.155,0.156 10 *a 1.054,2.735 1.45,2.891 0.397,0.156 10 MUT2 1.55,2.222 1.371,2.72 false
*a Front view of wire harness connector
(to Navigation ECU Sub-assembly)


Reconnect the stereo component amplifier assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I67-20 (MUT2) - Body ground Ignition switch ACC, audio system is playing Above 3.5 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY