Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2014.05–2015.04
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  P0355  Ignition Coil "E" Primary / Secondary Circuit  P0356  Ignition Coil "F" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the No. 1 ignition coil assembly (No. 1 cylinder) circuit.

·

If DTC P0352 is output, check the No. 2 ignition coil assembly (No. 2 cylinder) circuit.

·

If DTC P0353 is output, check the No. 3 ignition coil assembly (No. 3 cylinder) circuit.

·

If DTC P0354 is output, check the No. 4 ignition coil assembly (No. 4 cylinder) circuit.

·

If DTC P0355 is output, check the No. 5 ignition coil assembly (No. 5 cylinder) circuit.

·

If DTC P0356 is output, check the No. 6 ignition coil assembly (No. 6 cylinder) circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.

A256625E04
5.49,1.292 5.625,0.844 5.625,0.844 5.75,0.844 false 4.802,1.01 4.969,1.01 false 4.969,1.01 4.76,1.688 false 3.021,8 3.375,8.177 0.354,0.177 10 false ECM 0.313,1.979 2.063,2.156 1.75,0.177 10 false Crankshaft Position Sensor 0.354,4.083 2.031,4.26 1.677,0.177 10 false VVT Sensor 0.229,5.76 2.104,6.313 1.875,0.552 10 false Other Sensors (Engine Coolant Temperature Sensor, Throttle Position Sensor, etc.) 3.167,1.51 3.542,1.688 0.375,0.177 10 false IGT1 4.813,0.417 5.656,0.594 0.844,0.177 10 false from Battery 5.771,0.771 6.906,1.135 1.135,0.365 10 false No. 1 Ignition Coil Assembly 4.396,2.802 5.542,3.156 1.146,0.354 10 false No. 2 Ignition Coil Assembly 5.823,1.531 6.771,1.708 0.948,0.177 10 false No. 1 Cylinder 5.813,3.271 6.76,3.448 0.948,0.177 10 false No. 2 Cylinder 4.396,3.896 5.542,4.219 1.146,0.323 10 false No. 3 Ignition Coil Assembly 5.813,4.365 6.76,4.542 0.948,0.177 10 false No. 3 Cylinder 4.396,4.969 5.542,5.281 1.146,0.313 10 false No. 4 Ignition Coil Assembly 5.813,5.448 6.76,5.625 0.948,0.177 10 false No. 4 Cylinder 4.396,6.052 5.542,6.427 1.146,0.375 10 false No. 5 Ignition Coil Assembly 5.813,6.531 6.76,6.708 0.948,0.177 10 false No. 5 Cylinder 4.417,7.135 5.563,7.479 1.146,0.344 10 false No. 6 Ignition Coil Assembly 5.813,7.615 6.76,7.792 0.948,0.177 10 false No. 6 Cylinder 5.938,2.042 6.677,2.219 0.74,0.177 10 false Spark Plug 4.375,0.927 4.813,1.104 0.438,0.177 10 false Igniter 3.156,1.948 3.479,2.125 0.323,0.177 10 false IGF1 3.167,2.875 3.542,3.052 0.375,0.177 10 false IGT2 3.167,3.979 3.542,4.156 0.375,0.177 10 false IGT3 3.167,5.063 3.542,5.24 0.375,0.177 10 false IGT4 3.167,6.146 3.542,6.323 0.375,0.177 10 false IGT5 3.167,7.229 3.542,7.406 0.375,0.177 10 false IGT6

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0351 Ignition Coil "A" Primary / Secondary Circuit No IGF signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT1 circuit between ignition coil assembly and ECM

·

No. 1 ignition coil assembly

·

ECM


Comes on DTC stored
P0352 Ignition Coil "B" Primary / Secondary Circuit No IGF signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT2 circuit between ignition coil assembly and ECM

·

No. 2 ignition coil assembly

·

ECM


Comes on DTC stored
P0353 Ignition Coil "C" Primary / Secondary Circuit No IGF signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT3 circuit between ignition coil assembly and ECM

·

No. 3 ignition coil assembly

·

ECM


Comes on DTC stored
P0354 Ignition Coil "D" Primary / Secondary Circuit No IGF signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT4 circuit between ignition coil assembly and ECM

·

No. 4 ignition coil assembly

·

ECM


Comes on DTC stored
P0355 Ignition Coil "E" Primary / Secondary Circuit No IGF signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT5 circuit between ignition coil assembly and ECM

·

No. 5 ignition coil assembly

·

ECM


Comes on DTC stored
P0356 Ignition Coil "F" Primary / Secondary Circuit No IGF signal to ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT6 circuit between ignition coil assembly and ECM

·

No. 6 ignition coil assembly

·

ECM


Comes on DTC stored

A210049E07
0.135,0.077 2.124,0.381 1.989,0.304 10 IGT and IGF Signal Waveforms 2.713,0.513 3.258,0.771 0.545,0.258 10 2 V/DIV. 2.891,2.558 3.241,2.705 0.350,0.147 10 GND 2.891,1.699 3.241,1.845 0.350,0.147 10 GND 0.175,1.203 0.437,1.352 0.262,0.149 10 IGT 1.163,2.761 1.930,2.924 0.767,0.163 10 20 ms./DIV. 0.175,2.028 0.437,2.177 0.262,0.149 10 IGF

Reference: Inspection using an oscilloscope.

While idling the engine, check the waveform between terminals IGT (1 to 6) and E1, and IGF1 and E1 of the ECM connectors.

ECM Terminal Name Between IGT (1 to 6) and E1
Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

A212405E11
1.782,1.645 2.181,1.818 0.399,0.173 10 ECM 2.956,1.3 3.225,1.485 0.269,0.185 10 IGT 2.949,1.726 3.226,1.886 0.278,0.160 10 IGF 4.153,1.509 4.594,1.655 0.441,0.145 10 Igniter 5.4,1.348 6.167,1.521 0.767,0.173 10 Ignition Coil 4.465,2.35 5.868,2.540 1.404,0.191 10 Ignition Coil Assembly 0.213,3.113 1.146,3.443 0.934,0.330 10 Ignition Signal (IGT) 1.642,3.541 2.131,3.731 0.489,0.191 10 Normal 1.383,3.947 2.150,4.138 0.767,0.191 10 Malfunction 0.185,3.891 1.153,4.408 0.968,0.517 10 Ignition Confirmation Signal (IGF) 3.631,4.507 4.482,4.684 0.850,0.177 10 Circuit Open 5.95,4.97 6.314,5.167 0.364,0.198 10 Time

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Igniter (Cylinder 1 to 6)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine / DTC.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P0351, P0352, P0353, P0354, P0355 or P0356.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A255658E06
5.938,1.104 6.281,1.302 0.344,0.198 10 false IGT1 3.302,1.594 5.104,1.781 1.802,0.188 10 false No. 1 Ignition Coil Assembly 3.24,0.823 3.344,1.021 0.104,0.198 10 false 1 3.24,1.208 3.344,1.406 0.104,0.198 10 false 4 3.427,0.896 3.635,1.094 0.208,0.198 10 false +B 3.427,1.323 3.771,1.542 0.344,0.219 10 false GND 3.99,0.896 4.333,1.094 0.344,0.198 10 false IGT1 4.083,1.313 4.354,1.521 0.271,0.208 10 false IGF 4.406,1.219 4.51,1.417 0.104,0.198 10 false 2 4.406,0.802 4.646,1.104 0.24,0.302 10 false 3 3.24,2.073 3.344,2.271 0.104,0.198 10 false 1 3.24,2.469 3.344,2.667 0.104,0.198 10 false 4 3.427,2.125 3.635,2.323 0.208,0.198 10 false +B 3.427,2.583 3.771,2.802 0.344,0.219 10 false GND 3.99,2.125 4.333,2.323 0.344,0.198 10 false IGT2 3.302,2.865 5.083,3.063 1.781,0.198 10 false No. 2 Ignition Coil Assembly 4.406,2.469 4.51,2.667 0.104,0.198 10 false 2 4.417,2.073 4.521,2.271 0.104,0.198 10 false 3 0.427,0.938 0.729,1.198 0.302,0.26 10 false A 5.938,2.354 6.302,2.552 0.365,0.198 10 false IGT2 5.594,2.094 5.844,2.292 0.25,0.198 10 false 140 5.938,3.594 6.281,3.792 0.344,0.198 10 false IGT3 5.594,3.344 5.844,3.542 0.25,0.198 10 false 106 5.594,1.219 5.948,1.49 0.354,0.271 10 false 103 5.938,1.427 6.281,1.625 0.344,0.198 10 false IGF1 5.594,4.594 5.844,4.792 0.25,0.198 10 false 139 5.594,0.833 5.875,1.031 0.281,0.198 10 false 107 4.083,2.573 4.458,2.813 0.375,0.24 10 false IGF 3.24,3.333 3.344,3.531 0.104,0.198 10 false 1 3.24,3.729 3.344,3.927 0.104,0.198 10 false 4 4.406,3.729 4.51,3.927 0.104,0.198 10 false 2 4.406,3.344 4.51,3.542 0.104,0.198 10 false 3 3.24,4.594 3.344,4.792 0.104,0.198 10 false 1 3.24,4.969 3.458,5.229 0.219,0.26 10 false 4 4.396,4.979 4.635,5.25 0.24,0.271 10 false 2 4.396,4.573 4.677,4.885 0.281,0.313 10 false 3 3.24,5.823 3.344,6.021 0.104,0.198 10 false 1 3.24,6.229 3.344,6.427 0.104,0.198 10 false 4 4.406,6.229 4.51,6.427 0.104,0.198 10 false 2 4.406,5.844 4.51,6.042 0.104,0.198 10 false 3 3.25,7.479 3.354,7.677 0.104,0.198 10 false 4 4.406,7.49 4.51,7.688 0.104,0.198 10 false 2 4.406,7.104 4.51,7.302 0.104,0.198 10 false 3 4.01,3.438 4.354,3.635 0.344,0.198 10 false IGT3 4.083,3.792 4.333,3.99 0.25,0.198 10 false IGF 3.427,3.406 3.635,3.604 0.208,0.198 10 false +B 3.427,3.771 3.771,3.99 0.344,0.219 10 false GND 4.021,4.698 4.365,4.896 0.344,0.198 10 false IGT4 4.083,5.073 4.333,5.271 0.25,0.198 10 false IGF 3.406,4.688 3.615,4.885 0.208,0.198 10 false +B 3.427,5.083 3.771,5.302 0.344,0.219 10 false GND 4.021,5.948 4.469,6.198 0.448,0.25 10 false IGT5 4.083,6.323 4.448,6.583 0.365,0.26 10 false IGF 3.417,5.948 3.625,6.146 0.208,0.198 10 false +B 3.427,6.323 3.948,6.635 0.521,0.313 10 false GND 4.021,7.219 4.365,7.417 0.344,0.198 10 false IGT6 4.083,7.594 4.333,7.792 0.25,0.198 10 false IGF 3.427,7.188 3.635,7.385 0.208,0.198 10 false +B 3.427,7.594 3.771,7.813 0.344,0.219 10 false GND 3.302,4.146 5.094,4.344 1.792,0.198 10 false No. 3 Ignition Coil Assembly 3.302,5.385 5.083,5.583 1.781,0.198 10 false No. 4 Ignition Coil Assembly 3.302,6.635 5.083,6.833 1.781,0.198 10 false No. 5 Ignition Coil Assembly 3.302,7.885 5.083,8.083 1.781,0.198 10 false No. 6 Ignition Coil Assembly 5.938,4.854 6.281,5.052 0.344,0.198 10 false IGT4 5.938,6.115 6.281,6.313 0.344,0.198 10 false IGT5 5.594,5.844 5.948,6.083 0.354,0.24 10 false 105 5.938,7.365 6.313,7.563 0.375,0.198 10 false IGT6 5.594,7.094 5.854,7.292 0.26,0.198 10 false 138 6.063,8.156 6.354,8.354 0.292,0.198 10 false E26 6.375,8.156 6.719,8.354 0.344,0.198 10 false ECM 2.958,1.594 3.375,1.813 0.417,0.219 10 false E78 2.958,2.865 3.448,3.115 0.49,0.25 10 false E81 2.958,4.146 3.25,4.302 0.292,0.156 10 false E79 2.958,5.385 3.25,5.542 0.292,0.156 10 false E82 2.958,6.635 3.25,6.792 0.292,0.156 10 false E80 2.958,7.896 3.25,8.052 0.292,0.156 10 false E83 3.24,7.104 3.344,7.302 0.104,0.198 10 false 1

A270935E02
0.823,2.688 1.438,2.948 0.615,0.26 10 false Battery 1.208,1.031 1.948,1.323 0.74,0.292 10 false IG2-MAIN 0.667,1.615 1.365,1.875 0.698,0.26 10 false FL MAIN 2.625,0.719 2.969,1.031 0.344,0.313 10 false 3 2.573,0.906 3.083,1.198 0.51,0.292 10 false 1D 2.625,1.063 2.885,1.302 0.26,0.24 10 false 2 2.573,1.25 2.906,1.479 0.333,0.229 10 false 1E 4.917,0.719 5.104,0.958 0.188,0.24 10 false 1 4.865,0.896 5.26,1.146 0.396,0.25 10 false 1A 4.927,1.063 5.156,1.292 0.229,0.229 10 false 8 4.865,1.24 5.177,1.49 0.313,0.25 10 false 1C 6.521,0.896 6.854,1.156 0.333,0.26 10 false A 6.073,2.604 6.313,2.865 0.24,0.26 10 false 9 5.667,2.708 6.146,2.969 0.479,0.26 10 false IG2D 4.25,3.156 4.75,3.438 0.5,0.281 10 false A43 4.25,3.323 7.156,3.646 2.906,0.323 10 false Certification ECU (Smart Key ECU Assembly) 4.219,1.021 4.49,1.177 0.271,0.156 10 false IGN 3.094,1.885 4.75,2.229 1.656,0.344 10 false No. 1 Integration Relay 3.438,1.583 3.885,1.906 0.448,0.323 10 false IG2 0.146,0.052 2.76,0.313 2.615,0.26 12 false w/ Smart Entry and Start System:

A266827E05
4.188,0.833 4.563,1.042 0.375,0.208 10 false IGN 0.667,2.792 1.365,3.031 0.698,0.24 10 false Battery 0.573,2.031 1.344,2.333 0.771,0.302 10 false FL MAIN 3.406,1.469 3.896,1.781 0.49,0.313 10 false IG2 2.448,0.979 2.615,1.167 0.167,0.188 10 false 2 4.854,0.51 5.021,0.698 0.167,0.188 10 false 1 2.438,0.51 2.604,0.698 0.167,0.188 10 false 3 4.865,0.979 5.031,1.167 0.167,0.188 10 false 8 1.438,0.833 2.198,1.115 0.76,0.281 10 false IG2-MAIN 4.552,2.615 4.938,2.833 0.385,0.219 10 false IG2 4.865,2.385 5.01,2.573 0.146,0.188 10 false 6 6.427,0.698 6.719,0.979 0.292,0.281 10 false A 3.563,2.875 3.927,3.115 0.365,0.24 10 false I36 3.563,3.021 5.083,3.438 1.521,0.417 10 false Ignition or Starter Switch Assembly 0.042,0.031 2.75,0.313 2.708,0.281 12 false w/o Smart Entry and Start System: 2.969,1.76 4.521,2 1.552,0.24 10 false No. 1 Integration Relay 2.396,0.698 2.708,0.948 0.313,0.25 10 false 1D 4.813,0.688 5.198,0.99 0.385,0.302 10 false 1A 4.813,1.146 5.156,1.417 0.344,0.271 10 false 1C 2.396,1.146 2.74,1.375 0.344,0.229 10 false 1E 0.719,1.688 1.344,1.958 0.625,0.271 10 false ST/AM2 3.917,2.615 4.333,2.823 0.417,0.208 10 false AM2 3.75,2.385 3.896,2.573 0.146,0.188 10 false 5 4.896,2.646 6.125,2.927 1.229,0.281 10 false ECU-IG2 NO. 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E78-4 (GND) - Body ground Always Below 1 Ω
E81-4 (GND) - Body ground Always Below 1 Ω
E79-4 (GND) - Body ground Always Below 1 Ω
E82-4 (GND) - Body ground Always Below 1 Ω
E80-4 (GND) - Body ground Always Below 1 Ω
E83-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
a.
A335505C08
0.094,0.781 0.521,1.021 0.427,0.24 0.094,1.469 0.521,1.708 0.427,0.24 0.552,0.781 0.979,1.021 0.427,0.24 0.552,1.479 0.979,1.719 0.427,0.24 0.094,1.125 0.521,1.375 0.427,0.25 0.563,1.125 0.979,1.375 0.417,0.25 1.021,1.823 1.365,1.531 false 2.344,1.813 2.083,1.542 false 0.188,0.833 0.646,1.031 0.458,0.198 10 false E78 0.646,0.823 1.104,1.021 0.458,0.198 10 false E81 0.188,1.51 0.646,1.708 0.458,0.198 10 false E80 0.635,1.531 1.094,1.729 0.458,0.198 10 false E83 0.885,1.854 1.344,2.052 0.458,0.198 10 false +B 2.219,1.854 2.677,2.052 0.458,0.198 10 false GND 0.125,0.146 0.583,0.344 0.458,0.198 10 false *a 0.198,1.167 0.656,1.365 0.458,0.198 10 false E79 0.646,1.167 1.104,1.365 0.458,0.198 10 false E82
*a Front view of wire harness connector
(to Ignition Coil Assembly)


Disconnect the ignition coil assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E78-1 (+B) - E78-4 (GND) Ignition switch ON 11 to 14 V
E81-1 (+B) - E81-4 (GND) Ignition switch ON 11 to 14 V
E79-1 (+B) - E79-4 (GND) Ignition switch ON 11 to 14 V
E82-1 (+B) - E82-4 (GND) Ignition switch ON 11 to 14 V
E80-1 (+B) - E80-4 (GND) Ignition switch ON 11 to 14 V
E83-1 (+B) - E83-4 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E78-3 (IGT1) - E26-107 (IGT1) Always Below 1 Ω
E81-3 (IGT2) - E26-140 (IGT2) Always Below 1 Ω
E79-3 (IGT3) - E26-106 (IGT3) Always Below 1 Ω
E82-3 (IGT4) - E26-139 (IGT4) Always Below 1 Ω
E80-3 (IGT5) - E26-105 (IGT5) Always Below 1 Ω
E83-3 (IGT6) - E26-138 (IGT6) Always Below 1 Ω
E78-2 (IGF) - E26-103 (IGF1) Always Below 1 Ω
E81-2 (IGF) - E26-103 (IGF1) Always Below 1 Ω
E79-2 (IGF) - E26-103 (IGF1) Always Below 1 Ω
E82-2 (IGF) - E26-103 (IGF1) Always Below 1 Ω
E80-2 (IGF) - E26-103 (IGF1) Always Below 1 Ω
E83-2 (IGF) - E26-103 (IGF1) Always Below 1 Ω
E78-3 (IGT1) or E26-107 (IGT1) - Body ground Always 10 kΩ or higher
E81-3 (IGT2) or E26-140 (IGT2) - Body ground Always 10 kΩ or higher
E79-3 (IGT3) or E26-106 (IGT3) - Body ground Always 10 kΩ or higher
E82-3 (IGT4) or E26-139 (IGT4) - Body ground Always 10 kΩ or higher
E80-3 (IGT5) or E26-105 (IGT5) - Body ground Always 10 kΩ or higher
E83-3 (IGT6) or E26-138 (IGT6) - Body ground Always 10 kΩ or higher
E78-2 (IGF) or E26-103 (IGF1) - Body ground Always 10 kΩ or higher
E81-2 (IGF) or E26-103 (IGF1) - Body ground Always 10 kΩ or higher
E79-2 (IGF) or E26-103 (IGF1) - Body ground Always 10 kΩ or higher
E82-2 (IGF) or E26-103 (IGF1) - Body ground Always 10 kΩ or higher
E80-2 (IGF) or E26-103 (IGF1) - Body ground Always 10 kΩ or higher
E83-2 (IGF) or E26-103 (IGF1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 6 cylinders).

NOTICE:

Do not change the location of the connectors.



f.

Perform a simulation test.


g.

Enter the following menus: Powertrain / Engine / DTC.


h.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
Same DTC output A
Different ignition coil DTC output B


HINT:

Perform "Inspection After Repair" after replacing the ignition coil assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

B

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the ignition coil assembly connectors.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E78-1 (+B) - 1A-1 Always Below 1 Ω
E81-1 (+B) - 1A-1 Always Below 1 Ω
E79-1 (+B) - 1A-1 Always Below 1 Ω
E82-1 (+B) - 1A-1 Always Below 1 Ω
E80-1 (+B) - 1A-1 Always Below 1 Ω
E83-1 (+B) - 1A-1 Always Below 1 Ω
E78-1 (+B) or 1A-1 - Body ground Always 10 kΩ or higher
E81-1 (+B) or 1A-1 - Body ground Always 10 kΩ or higher
E79-1 (+B) or 1A-1 - Body ground Always 10 kΩ or higher
E82-1 (+B) or 1A-1 - Body ground Always 10 kΩ or higher
E80-1 (+B) or 1A-1 - Body ground Always 10 kΩ or higher
E83-1 (+B) or 1A-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR