Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › from 2015.04
RM2030EQ _59 Vehicle Exterior _014680 LIGHTING (EXT) _0164667 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM C

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  B241A  Rear Height Control Sensor  


DESCRIPTION

The headlight leveling ECU assembly receives signals indicating the height of the vehicle from the rear height control sensor sub-assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B241A Rear Height Control Sensor
·

Malfunction in rear height control sensor sub-assembly

·

Open or short in rear height control sensor sub-assembly circuit


·

Rear height control sensor sub-assembly

·

Harness or connector

·

Headlight leveling ECU assembly



WIRING DIAGRAM

E223762E23
1.563,0.823 1.979,0.979 0.417,0.156 10 false SHRR 4.781,0.719 5.021,0.896 0.24,0.177 10 false 19 4.781,1.385 4.969,1.563 0.188,0.177 10 false 21 4.781,2.052 4.969,2.229 0.188,0.177 10 false 12 2.073,2.052 2.198,2.229 0.125,0.177 10 false 3 2.073,1.385 2.198,1.563 0.125,0.177 10 false 1 2.073,0.719 2.198,0.896 0.125,0.177 10 false 2 1.646,1.458 1.979,1.615 0.333,0.156 10 false SHG 1.667,2.146 1.979,2.302 0.313,0.156 10 false SHB 5.031,0.823 5.438,0.979 0.406,0.156 10 false SHRL 5.021,1.458 5.406,1.615 0.385,0.156 10 false SGR 5.031,2.146 5.396,2.302 0.365,0.156 10 false SBR 4.906,2.667 5.219,2.844 0.313,0.177 10 false A78 4.896,2.833 6.417,3.188 1.521,0.354 10 false Headlight Leveling ECU Assembly 0.635,2.635 0.948,2.792 0.313,0.156 10 false O17 0.635,2.802 2.375,3.146 1.74,0.344 10 false Rear Height Control Sensor Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

If either of the following is performed, initialization of the headlight leveling ECU assembly is necessary.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>INITIALIZATION

·

Replacement of the headlight leveling ECU assembly.

·

Replacement or removal/installation of the rear height control sensor sub-assembly or work that changes the vehicle height such as replacement of suspension components.



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Clear DTCs
50002 165

b.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>DTC CHECK / CLEAR

Body Electrical > HL AutoLeveling > Trouble Codes
50001 165
OK:

DTC B241A is not output.



Result:
Proceed to
OK
NG



OK

NG

2.READ VALUE USING INTELLIGENT TESTER
2.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / HL AutoLeveling / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > HL AutoLeveling > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Height Sens Pw Supply Val Rear height control sensor sub-assembly power supply value 0.00 to 5.00 V Approx. 5 V -
Rr Height Sens Signal Val Rear height control sensor sub-assembly signal value 0.00 to 5.00 V Approx. 2.5 V (When vehicle is level) Value changes according to vehicle height
Body Electrical > HL AutoLeveling > Data List
Tester Display
Height Sens Pw Supply Val
Rr Height Sens Signal Val
50003 165 8,10
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

3.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY
3.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY
a.

Remove the rear height control sensor sub-assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL


b.

Inspect the rear height control sensor sub-assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY)

NG

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY)
a.

Disconnect the A78 headlight leveling ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A78-19 (SHRL) - O17-2 (SHRR) Always Below 1 Ω
A78-19 (SHRL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR