Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2015.04
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


MONITOR DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for over 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High When all of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):

(a) The vehicle speed is 20 km/h (12.43 mph) or more.

(b) The engine speed is 1000 rpm or higher.

(c) The STA signal is on.


·

Starter signal circuit

·

Park/Neutral position switch assembly

·

ECM


Comes on DTC stored

MONITOR STRATEGY

Required Sensors/Components (Main) ST relay
Park/Neutral position switch assembly
Certification ECU (smart key ECU assembly)
Required Sensors/Components (Related) Vehicle speed sensor
Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Vehicle speed 20 km/h (12.43 mph) or more
Engine speed 1000 rpm or higher

TYPICAL MALFUNCTION THRESHOLDS

Starter On

CONFIRMATION DRIVING PATTERN

A231469E52
1.229,1.979 1.656,2.198 0.427,0.219 10 false Idling 0.24,2.25 1.729,2.604 1.49,0.354 10 false Engine Switch on (IG) 1.063,0.865 1.635,1.073 0.573,0.208 10 false 24 km/h 2.396,2.854 3.083,3.167 0.688,0.313 10 false 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 false 20 seconds or more 2.01,2.333 2.302,2.552 0.292,0.219 10 false [A] 2.615,2.125 2.823,2.302 0.208,0.177 10 false [B] 4.063,0.458 4.292,0.625 0.229,0.167 10 false [C] 4.885,3.333 5.115,3.5 0.229,0.167 10 false [D]

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on [A].

6.

Start the engine.

7.

Idle the engine for 5 seconds or more [B].

8.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P0617.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.




WIRING DIAGRAM

A266832E12
5.74,3.677 6.115,3.854 0.375,0.177 10 false STA 5.417,3.594 5.604,3.75 0.188,0.156 10 false 9 5.354,3.771 5.625,3.927 0.271,0.156 10 false A25 5.719,0.677 6.094,0.854 0.375,0.177 10 false NEO 5.375,0.594 5.563,0.75 0.188,0.156 10 false 22 5.344,0.771 5.615,0.927 0.271,0.156 10 false A25 5.74,1.427 6.115,1.604 0.375,0.177 10 false NSW 5.375,1.417 5.563,1.573 0.188,0.156 10 false 65 5.344,1.594 5.615,1.75 0.271,0.156 10 false E26 6.135,4.948 6.479,5.115 0.344,0.167 10 false ECM 3.552,2.26 3.656,2.417 0.104,0.156 10 false 9 3.719,2.26 3.823,2.417 0.104,0.156 10 false L 4.375,2.26 4.49,2.417 0.115,0.156 10 false B 4.583,2.26 4.708,2.417 0.125,0.156 10 false 4 3.333,2.656 3.813,2.844 0.479,0.188 10 false E77 3.292,2.854 5.073,3.188 1.781,0.333 10 false Park/Neutral Position Switch Assembly 0.615,3.823 1.146,3.979 0.531,0.156 10 false ST/AM2 0.615,4.917 1.229,5.073 0.615,0.156 10 false FL MAIN 1.49,0.771 1.906,0.969 0.417,0.198 10 false NE 1.802,0.677 2.063,0.833 0.26,0.156 10 false 16 1.333,1.594 1.719,1.75 0.385,0.156 10 false STAR 1.802,1.5 1.927,1.656 0.125,0.156 10 false 5 1.427,2.115 1.719,2.271 0.292,0.156 10 false STA 1.802,2.021 1.927,2.177 0.125,0.156 10 false 7 0.198,2.542 0.51,2.708 0.313,0.167 10 false A43 0.198,2.708 2.031,3.083 1.833,0.375 10 false Certification ECU (Smart Key ECU Assembly) 3.292,4.615 3.521,4.771 0.229,0.156 10 false ST 3.021,4.146 3.146,4.302 0.125,0.156 10 false 2 3.021,5.052 3.146,5.208 0.125,0.156 10 false 1 2.594,4.146 2.688,4.302 0.094,0.156 10 false 5 2.594,5.052 2.688,5.208 0.094,0.156 10 false 3 1.771,5.5 1.979,5.656 0.208,0.156 10 false E9 1.771,5.333 1.865,5.49 0.094,0.156 10 false 1 1.135,5.75 1.26,5.917 0.125,0.167 10 false 1 1.063,5.906 1.281,6.063 0.219,0.156 10 false F2 1.563,6.708 2.198,7.083 0.635,0.375 10 false Starter Assembly 0.75,6.823 1.229,6.99 0.479,0.167 10 false Battery

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



Result:
Condition Starter Signal Proceed to
Driving at 20 km/h (12.4 mph) or more OFF A
ON B



A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (park/neutral position switch assembly - ST relay - ECM - certification ECU (smart key ECU assembly)).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234

Result:
Result Proceed to
DTC is not output A
DTC P0617 is output B



A

END

B