Home › Brake › PARKING BRAKE › PARKING BRAKE SYSTEM › from 2015.04
RM2030EQ _54 Brake _014654 PARKING BRAKE _0074522 PARKING BRAKE SYSTEM N

PARKING BRAKE  PARKING BRAKE SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT PARKING BRAKE PEDAL TRAVEL

a.

Fully depress the parking brake pedal to engage the parking brake.


b.

Depress the pedal again to disengage the parking brake.


c.
C233618

Slowly depress the parking brake pedal using the specified force, and count the number of clicks.

Parking brake pedal travel (for LHD):

7 to 10 notches at 300 N (31 kgf, 67.5 lbf)


Parking brake pedal travel (for RHD):

9 to 12 notches at 300 N (31 kgf, 67.5 lbf)


If the parking brake pedal travel is not as specified, adjust the parking brake shoe clearance and parking brake pedal travel.


Hide 2.ADJUST PARKING BRAKE PEDAL TRAVEL (for LHD)

a.

Completely release the parking brake pedal.


b.
C237831C01
0.854,1.531 2.396,1.531 true 0.802,1.625 1.979,1.979 1.979,1.979 2.385,1.979 true 2.427,1.896 2.583,2.063 0.156,0.167 10 *1 2.438,1.448 2.594,1.615 0.156,0.167 10 *2
*1 Lock Nut
*2 Adjusting Nut


Loosen the lock nut and the adjusting nut to completely release the parking brake cable.


c.

Remove the rear wheels.


d.

Separate the rear disc brake caliper assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB BOLT>REPLACEMENT


e.

Remove the parking brake shoe adjusting hole plug.


f.

Remove the rear disc.

Click hereBrake>BRAKE (REAR)>REAR BRAKE>REMOVAL


g.
C240909

Measure the brake shoe diameter as shown in the illustration.

Standard diameter:

189.6 to 189.7 mm (7.46 to 7.47 in.)



h.
C171323C01
1.146,1.167 1.146,1.865 false 1.073,1.885 1.458,2.104 0.385,0.219 10 false *1
*1 Nut


If the shoe diameter is not as specified, adjust it by turning the nut.


i.
C171324N01
0.885,0.083 1.229,0.365 0.344,0.281 10 false (A)

The gap between the adjusting nut and screw must not exceed 5 mm (0.197 in.). If the gap is set to this specification and the shoe diameter is less than specified, replace the parking brake shoe. If the lining thickness is less than 1.5 mm (0.0591 in.) or exhibits uneven wear, replace the parking brake shoe.

Dimension (A):

5 mm (0.197 in.) max



j.

Install the rear disc.

Click hereBrake>BRAKE (REAR)>REAR BRAKE>INSTALLATION


k.

Check for drag. Spin the rotor and ensure there is no drag from the parking brake shoe.

HINT:

If there is drag, apply and release the parking brake pedal and retest. If drag is still present, remove the disc, remeasure and readjust the shoe diameter and centralize the shoe. Reassemble the disc and recheck for drag.



l.

Install the parking brake shoe adjusting hole plug.


m.

Install the rear disc brake caliper assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB BOLT>REPLACEMENT


n.

Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

Parking brake pedal travel:

7 to 10 notches at 300 N (31 kgf, 67.5 lbf)



o.

Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


p.

Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.


q.

Check that the parking brake does not drag.


r.

Install the rear wheels.

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)


Hide 3.ADJUST PARKING BRAKE PEDAL TRAVEL (for RHD)

a.

Completely release the parking brake pedal.


b.
C247507C01
0.854,1.448 1.438,1.448 true 0.396,1.417 0.729,1.417 true 1.469,1.354 1.781,1.552 0.313,0.198 10 false *1 0.24,1.333 0.552,1.531 0.313,0.198 10 false *2
*1 Lock Nut
*2 Adjusting Nut


Loosen the lock nut and the adjusting nut to completely release the parking brake cable.


c.

Remove the rear wheels.


d.

Separate the rear disc brake caliper assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB BOLT>REPLACEMENT


e.

Remove the parking brake shoe adjusting hole plug.


f.

Remove the rear disc.

Click hereBrake>BRAKE (REAR)>REAR BRAKE>REMOVAL


g.
C240909

Measure the brake shoe diameter as shown in the illustration.

Standard diameter:

189.6 to 189.7 mm (7.46 to 7.47 in.)



h.
C171323C01
1.146,1.167 1.146,1.865 false 1.073,1.885 1.458,2.104 0.385,0.219 10 false *1
*1 Nut


If the shoe diameter is not as specified, adjust it by turning the nut.


i.
C171324N01
0.885,0.083 1.229,0.365 0.344,0.281 10 false (A)

The gap between the adjusting nut and screw must not exceed 5 mm (0.197 in.). If the gap is set to this specification and the shoe diameter is less than specified, replace the parking brake shoe. If the lining thickness is less than 1.5 mm (0.0591 in.) or exhibits uneven wear, replace the parking brake shoe.

Dimension (A):

5 mm (0.197 in.) max



j.

Install the rear disc.

Click hereBrake>BRAKE (REAR)>REAR BRAKE>INSTALLATION


k.

Check for drag. Spin the rotor and ensure there is no drag from the parking brake shoe.

HINT:

If there is drag, apply and release the parking brake pedal and retest. If drag is still present, remove the disc, remeasure and readjust the shoe diameter and centralize the shoe. Reassemble the disc and recheck for drag.



l.

Install the parking brake shoe adjusting hole plug.


m.

Install the rear disc brake caliper assembly.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB BOLT>REPLACEMENT


n.

Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

Parking brake pedal travel:

9 to 12 notches at 300 N (31 kgf, 67.5 lbf)



o.

Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


p.

Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.


q.

Check that the parking brake does not drag.


r.

Install the rear wheels.

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)


Hide 4.INSPECT BRAKE WARNING LIGHT

a.

When operating the parking brake pedal, check that the brake warning light illuminates.

Standard:

The brake warning light always illuminates at the first click.