Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT › from 2015.04
RM2030EQ _52 Drivetrain _014645 AXLE AND DIFFERENTIAL _0074485 REAR AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  REAR AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 2.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

a.
C083014

Remove the bolt and separate the rear flexible hose from the rear shock absorber assembly.


b.

Remove the 2 bolts, and separate the rear disc brake caliper assembly.

NOTICE:

Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging down by the rear flexible hose.



Hide 42491 3.REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 42431 4.REMOVE REAR DISC

Hide 42312E 5.REMOVE REAR AXLE HUB BOLT

a.
C246309C02
2.177,1.083 2.521,1.083 false 1.313,1.375 1.313,1.823 true 1.604,0.927 1.604,0.708 1.604,0.708 0.958,0.708 false 2.521,1 2.833,1.156 0.313,0.156 10 false SST 1.25,1.854 1.417,2.01 0.167,0.156 10 true *1 0.792,0.625 0.958,0.781 0.167,0.156 10 true *1
*1 Nut


Temporarily install 2 nuts to the rear axle hub bolts as shown in the illustration.

Recommended service nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


NOTICE:

Install the nuts to prevent damage to the rear axle hub bolts.



b.

Using SST and a brass bar or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

SST
09628-10011  

NOTICE:

Do not damage the threads of the rear axle hub bolts.



Hide 42312E 6.INSTALL REAR AXLE HUB BOLT

a.
C246310C03
3.052,0.469 3.052,0.125 3.052,0.125 3.156,0.125 false 2.74,0.333 2.74,0.146 2.74,0.146 2.313,0.146 true 3.167,0.042 3.354,0.219 0.188,0.177 10 true *1 2.156,0.052 2.323,0.208 0.167,0.156 10 true *2
*1 Nut
*2 Washer


Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.


b.

Install a washer and nut to the rear axle hub bolt as shown in the illustration.

Recommended service nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



c.

Using a brass bar or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the nut.

NOTICE:
·

Install the nuts to prevent damage to the rear axle hub bolts.

·

Do not damage the threads of the rear axle hub bolts.




d.

Remove the 3 nuts and washer from the 3 rear axle hub bolts.


Hide 42431 7.INSTALL REAR DISC

Hide 42491 8.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

Hide 9.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

a.

Install the rear disc brake caliper assembly with the 2 bolts.

Torque:
47 N*m (475 kgf*cm, 34 ft.*lbf)


b.

Install the rear flexible hose to the rear shock absorber assembly with the bolt.

Torque:
19 N*m (192 kgf*cm, 14 ft.*lbf)


Hide 10.ADJUST PARKING BRAKE

Hide 11.INSTALL REAR WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)