Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › from 2015.04
RM2030EQ _59 Vehicle Exterior _014677 DOOR / HATCH _0074691 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69284C 3.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B288548

Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.


Hide 67492A 4.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B288549

Disengage the 3 clips and remove the front door lower frame bracket garnish.


Hide 5.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.
B277183

Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.


b.

Disconnect each connector and remove the power window regulator master switch assembly with front door armrest base panel.


Hide 6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.
B281683

Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.


b.

Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.


Hide 74220 7.REMOVE FRONT ARMREST ASSEMBLY

a.
B277187

Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the front armrest assembly.


Hide 81230 8.REMOVE COURTESY LIGHT ASSEMBLY

Hide 67602 9.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B288550C04
1.292,0.635 1.594,0.427 false 1.125,0.573 1.573,0.813 0.448,0.24 10 false *1
*1 Protective Tape


Put protective tape around the front door panel.


b.
B288551

Remove the 3 screws.


c.

Using a clip remover, disengage the 10 clips.


d.
B288552C04
0.927,4.229 0.667,4.229 false 1.583,0.719 1.063,1.021 false 0.479,4.135 0.823,4.385 0.344,0.25 10 false *1 0.896,0.958 1.323,1.208 0.427,0.25 10 false *2
*1 Reference Boss
*2 Front Door Inner Glass Weatherstrip


Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.


e.

Disengage the reference boss from the front door panel.


f.

Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.


g.

Disconnect the connector.


h.
B277192

Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.


Hide 69206B 10.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B277194

Disengage the 2 claws and guides, and remove the front door inside handle sub-assembly.


Hide 68172A 11.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP

a.
B277195C07
3.063,1.01 3.01,0.896 false 2.99,1.01 3.313,1.302 0.323,0.292 10 false *1
*1 Screwdriver


Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.


Hide 84927 12.REMOVE SEAT MEMORY SWITCH (w/ Memory)

Hide 86160 13.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 14.REMOVE MIRROR SUB-ASSEMBLY WITH COVER

Hide 89430 15.REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Memory)

Hide 67832 16.REMOVE FRONT DOOR SERVICE HOLE COVER

a.
B310448

Disconnect each connector.


b.

Disengage the 3 clamps.


c.

Remove the front door service hole cover.

HINT:

Remove any remaining butyl tape from the door.



Hide 68102 17.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

a.
B281733

Remove the grommet.


b.

Connect the cable to the negative (-) battery terminal.


c.

Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


d.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



e.

Disconnect the power window regulator master switch assembly.


f.
B288542

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the door glass to fall.



g.
B288543E01
0.615,0.188 0.969,0.427 0.354,0.24 10 false (1) 1.375,0.115 1.719,0.354 0.344,0.24 10 false (2)

Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

NOTICE:

Do not damage the door glass.



Hide 18.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.
B281734C05
1.167,0.146 1.896,0.813 false 1.01,0.042 1.333,0.292 0.323,0.25 10 false *1
*1 Temporary Bolt


Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.



b.

Remove the 5 bolts.


c.

Remove the front door window regulator assembly.


d.

Remove the temporary bolt from the front door window regulator assembly.


Hide 85720D 19.REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

a.
B280344

Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.


Hide 67924 20.REMOVE NO. 2 FRONT DOOR STIFFENER CUSHION

a.
B281687C03
2.292,1.333 1.406,1.417 false 1.24,1.313 1.688,1.583 0.448,0.271 10 false *1
*1 Double-sided Tape


Remove the 2 bolts.


b.

Disengage the 2 guides and remove the No. 2 front door stiffener cushion.


Hide 68151C 21.REMOVE FRONT DOOR GLASS RUN

a.
B281735

Remove the front door glass run.


Hide 67402F 22.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B280347

Remove the 2 bolts.


b.

Disengage the guide and remove the front door front lower frame sub-assembly as shown in the illustration.


Hide 67404F 23.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B288544

Remove the 2 bolts.


b.

Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.


Hide 24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B280351

Remove the hole plug.


b.
B280352

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 69217F 25.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B280353

Using a screwdriver, disengage the claw and 2 guides, and remove the front door outside handle cover as shown in the illustration.


Hide 69217F 26.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B280630

Remove the hole plug.


b.
B280355

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 69220 27.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B280356

Disengage the 2 claws.


b.

Using a screwdriver, disconnect the connector.


c.
B280357

Remove the front door outside handle assembly as shown in the illustration.


Hide 69241H 28.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B280359

Disengage the 3 claws and remove the front door front outside handle pad.


Hide 69242E 29.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B280360

Disengage the 2 claws and remove the front door rear outside handle pad.


Hide 69040A 30.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY

a.
B280361C10
2.969,2.635 3.135,2.781 false 3.156,2.698 3.427,2.958 0.271,0.26 10 false *1
*1 Front Door Lock Open Rod


Using a T30 "TORX" socket wrench, remove the 3 screws.


b.

Slide the front door lock with motor assembly downward, and remove the front door lock with motor assembly and cables as a unit.


c.

When reusing the front door lock with motor assembly:

i.
B280363

Remove the door lock wiring harness seal from the front door lock with motor assembly.



Hide 69720B 31.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B280364

Remove the front door lock remote control cable assembly.


Hide 69760C 32.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B280366

Using a screwdriver, disengage the 3 claws.


b.
B280367

Remove the front door inside locking cable assembly.


Hide 69202A 33.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B280369

Disconnect the connector.


b.

Disengage the 3 clamps.


c.
B280370C06
0.365,1.844 0.698,1.708 false 0.188,1.781 0.479,2.031 0.292,0.25 10 false *1 0.083,0.104 0.521,0.417 0.438,0.313 10 false *a 0.083,2.167 0.531,2.521 0.448,0.354 10 false *b
*1 Door Handle Nut
*a Outside
*b Inside


Using a T30 "TORX" socket wrench, remove the screw and door handle nut.


d.

Slide the front door outside handle frame sub-assembly to disengage the claw of the front door outside handle frame sub-assembly, and then remove it.


Hide 82186B 34.REMOVE FRONT DOOR WIRE

a.
B280372

Disengage the 3 clamps and remove the front door wire.


Hide 69312 35.REMOVE FRONT DOOR LOCK OPEN ROD

a.
B280374E01
2.052,0.552 2.542,0.948 0.49,0.396 10 false (1) 2.813,0.635 3.167,0.948 0.354,0.313 10 false (2)

Remove the front door lock open rod as indicated by the arrows and in the order shown in the illustration.


Hide 68620 36.REMOVE FRONT DOOR CHECK ASSEMBLY

a.
B280375

Remove the 3 bolts and front door check assembly.


Hide 67862 37.REMOVE FRONT DOOR WEATHERSTRIP

a.
B281736

Using a clip remover, disengage the 19 clips and remove the front door weatherstrip.


Hide 67664C 38.REMOVE DOOR FRAME GARNISH

a.
B277197

Disengage the clip and remove the door frame garnish.

HINT:

This garnish needs to be replaced with a new one because the clip will break when removing it.



Hide 67864B 39.REMOVE FRONT DOOR NO. 2 WEATHERSTRIP

a.
B281737

Using a clip remover, disengage the 8 clips and remove the front door No. 2 weatherstrip.


Hide 67001A 40.REMOVE FRONT DOOR PANEL CUSHION

a.
B281738

Disengage the 2 claws and remove the 2 front door panel cushions.


Hide 67481C 41.REMOVE FRONT DOOR FRONT LOWER FRAME SEAL

a.
B280379

Remove the front door front lower frame seal.


Hide 75720 42.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

Hide 75756C 43.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

Hide 75754A 44.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

Hide 75976G 46.REMOVE FRONT DOOR LOWER OUTSIDE STRIPE