Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2015.04
RM2030EQ _56 Audio / Visual / Telematics _014659 NAVIGATION / MULTI INFO DISPLAY _0074553 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the navigation receiver assembly. This diagnostic procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

for 6 Speakers
E277817E40
0.24,3.625 1.396,4.021 1.156,0.396 10 false No. 1 Stereo Jack Adapter Assembly 0.979,0.615 1.583,0.833 0.604,0.219 10 false UPI 0.865,1.188 1.469,1.406 0.604,0.219 10 false UDO- 0.833,1.792 1.438,2.01 0.604,0.219 10 false UDO+ 0.854,2.438 1.458,2.656 0.604,0.219 10 false UJSG 0.865,3.042 1.469,3.26 0.604,0.219 10 false UJSS 1.333,2.927 1.531,3.135 0.198,0.208 10 false 5 1.333,2.313 1.531,2.521 0.198,0.208 10 false 4 1.333,1.646 1.531,1.854 0.198,0.208 10 false 3 1.333,1.042 1.531,1.25 0.198,0.208 10 false 2 1.333,0.479 1.531,0.688 0.198,0.208 10 false 1 3.302,2.833 4.833,3.031 1.531,0.198 10 false (Shielded) 5.958,0.615 6.563,0.833 0.604,0.219 10 false USV1 5.958,1.198 6.563,1.417 0.604,0.219 10 false US1- 5.958,1.813 6.563,2.031 0.604,0.219 10 false US1+ 5.958,2.448 6.563,2.667 0.604,0.219 10 false UGD1 5.958,3.052 6.563,3.271 0.604,0.219 10 false USG1 5.74,2.927 5.938,3.135 0.198,0.208 10 false 5 5.74,2.313 5.938,2.521 0.198,0.208 10 false 4 5.74,1.646 5.938,1.854 0.198,0.208 10 false 3 5.74,1.031 5.938,1.24 0.198,0.208 10 false 2 5.74,0.479 5.938,0.688 0.198,0.208 10 false 1 5.719,3.594 6.958,4.063 1.24,0.469 10 false Navigation Receiver Assembly 1.854,4.177 4.573,4.438 2.719,0.26 10 false : Data Signal (USB Communication Line) 0.24,3.448 0.573,3.688 0.333,0.24 10 false I146 5.719,3.438 6.104,3.667 0.385,0.229 10 false I147

for 10 Speakers
E277817E44
0.24,3.625 1.396,4.021 1.156,0.396 10 false No. 1 Stereo Jack Adapter Assembly 0.979,0.615 1.583,0.833 0.604,0.219 10 false UPI 0.865,1.188 1.469,1.406 0.604,0.219 10 false UDO- 0.833,1.792 1.438,2.01 0.604,0.219 10 false UDO+ 0.854,2.438 1.458,2.656 0.604,0.219 10 false UJSG 0.865,3.042 1.469,3.26 0.604,0.219 10 false UJSS 1.333,2.927 1.531,3.135 0.198,0.208 10 false 5 1.333,2.313 1.531,2.521 0.198,0.208 10 false 4 1.333,1.646 1.531,1.854 0.198,0.208 10 false 3 1.333,1.042 1.531,1.25 0.198,0.208 10 false 2 1.333,0.479 1.531,0.688 0.198,0.208 10 false 1 3.302,2.833 4.833,3.031 1.531,0.198 10 false (Shielded) 5.958,0.615 6.563,0.833 0.604,0.219 10 false UPO 5.958,1.198 6.563,1.417 0.604,0.219 10 false UDO- 5.948,1.813 6.552,2.031 0.604,0.219 10 false UDO+ 5.958,2.448 6.563,2.667 0.604,0.219 10 false UESG 5.958,3.052 6.563,3.271 0.604,0.219 10 false USG1 5.74,2.927 5.938,3.135 0.198,0.208 10 false 5 5.74,2.313 5.938,2.521 0.198,0.208 10 false 4 5.74,1.646 5.938,1.854 0.198,0.208 10 false 3 5.74,1.031 5.938,1.24 0.198,0.208 10 false 2 5.74,0.479 5.938,0.688 0.198,0.208 10 false 1 5.719,3.594 6.958,4.063 1.24,0.469 10 false Navigation Receiver Assembly 1.854,4.177 4.573,4.438 2.719,0.26 10 false : Data Signal (USB Communication Line) 0.24,3.448 0.573,3.688 0.333,0.24 10 false I146 5.719,3.438 6.104,3.667 0.385,0.229 10 false I147

CAUTION / NOTICE / HINT

HINT:
·

When a large amount of data is in a USB device, it may take a while to begin playback.

·

When using a USB device, files that are protected by copyright cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

1.

Add numbers in front of the file names.

2.

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>SYSTEM DESCRIPTION



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>SYSTEM DESCRIPTION


Result:
Result Proceed to
No playable files exist, or incompatible device format or version. A
Playable files exist, and compatible device format or version. B




A

END (USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENTED)

B

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the I147 navigation receiver assembly connector.


b.

Disconnect the I146 No. 1 stereo jack adapter assembly connector.


c.
E289734C03
1.479,0.115 1.906,0.333 0.427,0.219 1.51,2.323 1.938,2.542 0.427,0.219 1.01,0.906 1.583,1.26 false 0.938,1.792 1.594,1.438 false 1.833,1.271 2.396,1 false 1.833,1.427 2.385,1.729 false 1.781,1.552 2.104,1.938 false 1.135,3.198 1.51,3.427 false 1.104,3.688 1.635,3.448 false 1.792,3.427 2.375,3.021 false 1.917,3.438 2.292,3.531 false 1.771,3.542 2.302,3.854 false 0.625,0.729 1.24,0.927 0.615,0.198 10 false UGD1 0.135,0.125 0.75,0.323 0.615,0.198 10 false *a 1.573,0.146 2.188,0.344 0.615,0.198 10 false I147 0.583,1.771 1.198,1.969 0.615,0.198 10 false US1+ 2.115,1.948 2.729,2.146 0.615,0.198 10 false USG1 2.438,1.688 3.052,1.885 0.615,0.198 10 false US1- 2.438,0.875 3.052,1.073 0.615,0.198 10 false USV1 1.604,2.354 2.219,2.552 0.615,0.198 10 false I146 0.156,2.354 0.771,2.552 0.615,0.198 10 false *b 0.885,3.021 1.5,3.219 0.615,0.198 10 false UPI 0.74,3.667 1.354,3.865 0.615,0.198 10 false UDO- 2.406,2.875 3.021,3.073 0.615,0.198 10 false UDO+ 2.333,3.521 2.948,3.719 0.615,0.198 10 false UJSG 2.323,3.865 2.938,4.063 0.615,0.198 10 false UJSS
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the resistance according to the value(s) in the table below (for 6 Speakers).

Standard Resistance:
Tester Connection Condition Specified Condition
I146-1 (UPI) - I147-1 (USV1) Always Below 1 Ω
I146-2 (UDO-) - I147-2 (US1-) Always Below 1 Ω
I146-3 (UDO+) - I147-3 (US1+) Always Below 1 Ω
I146-4 (UJSG) - I147-4 (UGD1) Always Below 1 Ω
I146-5 (UJSS) - I147-5 (USG1) Always Below 1 Ω
I146-1 (UPI) - Body ground Always 10 kΩ or higher
I146-2 (UDO-) - Body ground Always 10 kΩ or higher
I146-3 (UDO+) - Body ground Always 10 kΩ or higher
I146-4 (UJSG) - Body ground Always 10 kΩ or higher
I146-5 (UJSS) - Body ground Always 10 kΩ or higher



d.
E289734C06
1.479,0.115 1.906,0.333 0.427,0.219 1.51,2.323 1.938,2.542 0.427,0.219 1.01,0.906 1.583,1.26 false 0.938,1.792 1.594,1.438 false 1.833,1.271 2.396,1 false 1.833,1.427 2.385,1.729 false 1.781,1.552 2.104,1.938 false 1.135,3.198 1.51,3.427 false 1.104,3.688 1.635,3.448 false 1.792,3.427 2.375,3.021 false 1.917,3.438 2.292,3.531 false 1.771,3.542 2.302,3.854 false 0.625,0.708 1.24,0.906 0.615,0.198 10 false UESG 0.135,0.125 0.75,0.323 0.615,0.198 10 false *a 1.573,0.146 2.188,0.344 0.615,0.198 10 false I147 0.583,1.771 1.198,1.969 0.615,0.198 10 false UDO+ 2.115,1.948 2.729,2.146 0.615,0.198 10 false USG1 2.438,1.688 3.052,1.885 0.615,0.198 10 false UDO- 2.438,0.875 3.052,1.073 0.615,0.198 10 false UPO 1.604,2.354 2.219,2.552 0.615,0.198 10 false I146 0.156,2.354 0.771,2.552 0.615,0.198 10 false *b 0.885,3.021 1.5,3.219 0.615,0.198 10 false UPI 0.74,3.667 1.354,3.865 0.615,0.198 10 false UDO- 2.406,2.875 3.021,3.073 0.615,0.198 10 false UDO+ 2.333,3.521 2.948,3.719 0.615,0.198 10 false UJSG 2.323,3.865 2.938,4.063 0.615,0.198 10 false UJSS
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the resistance according to the value(s) in the table below (for 10 Speakers).

Standard Resistance:
Tester Connection Condition Specified Condition
I146-1 (UPI) - I147-1 (UPO) Always Below 1 Ω
I146-2 (UDO-) - I147-2 (UDO-) Always Below 1 Ω
I146-3 (UDO+) - I147-3 (UDO+) Always Below 1 Ω
I146-4 (UJSG) - I147-4 (UESG) Always Below 1 Ω
I146-5 (UJSS) - I147-5 (USG1) Always Below 1 Ω
I146-1 (UPI) - Body ground Always 10 kΩ or higher
I146-2 (UDO-) - Body ground Always 10 kΩ or higher
I146-3 (UDO+) - Body ground Always 10 kΩ or higher
I146-4 (UJSG) - Body ground Always 10 kΩ or higher
I146-5 (UJSS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)
a.

Disconnect the I146 No. 1 stereo jack adapter assembly connector.


b.
E226479C36
1.5,0.917 1.99,1.208 0.49,0.292 1.958,2.083 2.552,2.302 false 1.5,2.083 0.854,2.302 false 2.563,2.271 2.99,2.417 0.427,0.146 10 false UJSG 0.542,2.271 0.813,2.417 0.271,0.146 10 false UPI 0.188,0.167 0.385,0.333 0.198,0.167 10 false *a 1.625,0.99 2,1.188 0.375,0.198 10 false I146
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I146-1 (UPI) - I146-4 (UJSG) Engine switch on (ACC) 5 V



Result:
Proceed to
OK
NG



OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/restore it.


b.

Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that a backup of the music data is available before performing this operation.


OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the engine switch off.

HINT:

When this malfunction occurs, it is necessary to turn the engine switch off to make it possible for the vehicle to recognize a new device when it is connected.



b.

Turn the engine switch on (ACC).


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

·

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>SYSTEM DESCRIPTION




Result:
Proceed to
NEXT



NEXT

6.CHECK USB DEVICE OR "iPod"
6.CHECK USB DEVICE OR "iPod"
a.

Check if a USB device or "iPod" is recognized by the navigation receiver assembly, and if information such as track, artist and album names is displayed on the screen.

OK:

USB device or "iPod" is recognized properly and the information is displayed on the screen.



Result:
Proceed to
OK
NG



OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE