The navigation receiver assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
Using this circuit, the navigation receiver assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly (telephone microphone assembly) sends microphone signals to the navigation receiver assembly.
Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
Push the recording switch and perform voice recording.
Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.
Voice can be recorded for up to 5 seconds.
Check that the recording indicator remains on while recording and that the recorded voice is played normally without noise or distortion.
All check results are normal.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Disconnect the I67 navigation receiver assembly connector.
Disconnect the S7 roof console box assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I67-6 (SNS2) - S7-15 (SNS2) | Always | Below 1 Ω |
| I67-4 (MACC) - S7-14 (MACC) | Always | Below 1 Ω |
| I67-5 (MIN+) - S7-13 (MCO+) | Always | Below 1 Ω |
| I67-19 (MIN-) - S7-12 (MCO-) | Always | Below 1 Ω |
| I67-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
| I67-4 (MACC) - Body ground | Always | 10 kΩ or higher |
| I67-5 (MIN+) - Body ground | Always | 10 kΩ or higher |
| I67-19 (MIN-) - Body ground | Always | 10 kΩ or higher |
| I67-18 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the I67 navigation receiver assembly connector.
Reconnect the S7 roof console box assembly (telephone microphone assembly) connector.
| *a | Component with harness connected
(Navigation Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I67-4 (MACC) - Body ground | Engine switch on (ACC) | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I67-18 (SGND) - Body ground | Always | Below 1 Ω |
| I67-19 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the roof console box assembly (telephone microphone assembly).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
| *a | Component without harness connected
(Roof Console Box Assembly (Telephone Microphone Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 12 (MCO-) - 15 (SNS2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the I67 navigation receiver assembly connector.
Reconnect the S7 roof console box assembly (telephone microphone assembly) connector.
Turn the engine switch on (ACC).
| *a | Component with harness connected
(Roof Console Box Assembly (Telephone Microphone Assembly)) |
Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the S7 roof console box assembly (telephone microphone assembly) connector.
Check the waveform of the roof console box assembly (telephone microphone assembly) using the oscilloscope.
| Result | Proceed to |
|---|---|
| A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is output. | A |
| A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output. | B |
A
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
B
Replace the telephone microphone assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL
Check if the same malfunction recurs.
| Result | Proceed to |
|---|---|
| Malfunction does not recur (returns to normal). | A |
| Malfunction recurs. | B |
A
B