Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.04
RM2030EQ _54 Brake _014650 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0077110 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1241  Low Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the +BS terminal voltage meets one of the DTC detection conditions due to a malfunction in the power supply or charging circuit such as the battery or alternator circuit, etc.

The DTC is canceled when the +BS terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1241 Low Power Supply Voltage Malfunction Any of the following is detected:
1.

The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (soft low voltage) is less than 9.6 V for 1 second or more.

2.

The vehicle speed is 6 km/h (4 mph) or more and the +BS terminal voltage (hard low voltage) is less than 6.9 V for 1 second or more.

3.

The vehicle speed is 15 km/h (9 mph) or more, the +BS terminal voltage is 9.6 V or more, the skid control ECU turns on more than one valve at the same time within a short period of time and the valve relay supply voltage drop exceeds the threshold. (The skid control ECU monitors the resistance of the power source line at the +BS terminal. A malfunction is detected when an abnormality occurs in the +BS terminal wire harness or its connection and the skid control ECU determines that the wiring resistance at the +BS terminal exceeds the standard resistance.)

4.

The +BS terminal voltage is less than 6.7 V and the skid control ECU judges that power supply voltage is abnormal for 0.06 seconds or more.


·

ABS NO. 2 fuse

·

Battery

·

Charging system

·

Power source circuit

·

Ground circuit

·

Internal power supply circuit of the skid control ECU



WIRING DIAGRAM

C324030E03
1.552,5.458 1.552,5.844 1.552,5.844 1.813,5.844 false 1.583,4.052 2.042,4.25 0.458,0.198 10 false 1 6.146,0.792 6.604,0.99 0.458,0.198 10 false IG1 6.156,4.833 6.615,5.031 0.458,0.198 10 false +BS 6.146,5.927 6.604,6.125 0.458,0.198 10 false GND1 5.906,5.813 6.365,6.01 0.458,0.198 10 false 38 5.906,4.729 6.365,4.927 0.458,0.198 10 false 25 5.906,0.667 6.365,0.865 0.458,0.198 10 false 28 3.927,0.948 5.094,1.188 1.167,0.24 10 false ECU-IG1 NO. 1 2.115,1.625 3.573,1.885 1.458,0.26 10 false IG1 NO. 2 0.458,3.146 0.917,3.344 0.458,0.198 10 false 1H 0.792,3.156 1.25,3.354 0.458,0.198 10 false 1 0.646,3.656 1.104,3.854 0.458,0.198 10 false ALT 2.302,4.052 2.76,4.25 0.458,0.198 10 false A43 0.656,4.99 1.531,5.24 0.875,0.25 10 false ABS NO. 2 0.49,5.26 0.948,5.458 0.458,0.198 10 false 1I 1.583,4.844 2.042,5.042 0.458,0.198 10 false 1 0.802,5.26 1.26,5.458 0.458,0.198 10 false 1 1.854,5.74 3.75,6.219 1.896,0.479 10 false Engine Room Relay Block and Junction Block Assembly 0.771,6.323 1.542,6.521 0.771,0.198 10 false Battery 1.906,4.479 5.031,4.917 3.125,0.438 10 false Certification ECU (Smart Key ECU Assembly) 2.677,4.042 3.135,4.24 0.458,0.198 10 false +B 3.396,4.042 3.854,4.24 0.458,0.198 10 false IG1D 3.854,4.052 4.313,4.25 0.458,0.198 10 false I78 3.906,3.844 4.365,4.042 0.458,0.198 10 false 6 2.396,3.833 2.854,4.031 0.458,0.198 10 false 2 0.854,4.219 1.313,4.417 0.458,0.198 10 false AM2 5.604,6.833 6.063,7.031 0.458,0.198 10 false A49 5.583,7.031 7.115,7.49 1.531,0.458 10 false Skid Control ECU (Brake Actuator Assembly) 0.667,5.729 1.542,5.979 0.875,0.25 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C238832C14
0.177,0.698 0.656,1.021 0.479,0.323 1.26,1.51 0.958,0.76 false 0.375,2.729 0.729,1.604 false 2.813,1.469 3.021,0.76 false 0.24,0.177 0.74,0.938 0.5,0.76 10 *a 0.313,0.781 0.771,1.01 0.458,0.229 10 A49 0.208,2.75 0.5,2.906 0.292,0.156 10 +BS 0.823,0.583 1.104,0.74 0.281,0.156 10 IG1 2.771,0.583 3.177,0.74 0.406,0.156 10 GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A49 skid control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-25 (+BS) - Body ground Always 11 to 14 V
A49-25 (+BS) - A49-38 (GND1) Always 11 to 14 V
A49-28 (IG1) - Body ground Engine switch on (IG) 11 to 14 V
A49-28 (IG1) - A49-38 (GND1) Engine switch on (IG) 11 to 14 V



Result:
Result Proceed to
OK A
NG (for +BS circuit) B
NG (for IG1 circuit) C



A

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

B

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C238832C15
0.208,0.719 0.688,1.042 0.479,0.323 2.823,1.5 2.219,0.75 false 0.271,0.198 0.573,0.521 0.302,0.323 10 *a 0.333,0.802 0.844,1.063 0.51,0.26 10 A49 1.948,0.563 2.542,0.917 0.594,0.354 10 GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the engine switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-38 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

4.RECONFIRM DTC
a.

Reconnect the A49 skid control ECU connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the engine switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1241 is not output. A
DTC C1241 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY)
a.

Turn the engine switch off.


b.

Disconnect the 1I engine room relay block and junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-25 (+BS) - 1I-1 Always Below 1 Ω


HINT:
·

Even if the resistance between the skid control ECU and the engine room relay block and junction block assembly is normal, there may be an abnormality in the resistance of the wiring between the battery and the engine room relay block and junction block assembly. Therefore, be sure to inspect the circuit between the battery and the engine room relay block and junction block assembly before replacing the skid control ECU (brake actuator assembly).

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE WIRE HARNESS OR ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY