The skid control ECU is connected to the combination meter assembly via CAN communication.
Pressing the vehicle stability control switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the TRC OFF message will be displayed on the multi-information display and the VSC OFF indicator light will come on.
When replacing the skid control ECU (brake actuator assembly), perform system variant learning.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Check if CAN communication system DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check if the skid control ECU connector is securely connected.
The connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Select the Data List using the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| TRC/VSC Off Mode | TRC/VSC off mode | Normal, TRC OFF, Unknown or VSC OFF | Normal: Normal mode
TRC OFF: TRC off mode Unknown: Unspecified VSC OFF: VSC off mode |
- |
| Tester Display |
|---|
| TRC/VSC Off Mode |
Check the indicator light and mode condition on the intelligent tester changes according to vehicle stability control switch operation.
| Switch Operation | Mode Condition Display | Multi-information Display (TRC OFF Message) | VSC OFF Indicator Light |
|---|---|---|---|
| Not pressed | Normal | Not displayed | Does not come on |
| Pressing the vehicle stability control switch | TRC OFF | Displayed | Does not come on |
| Pressing and holding the vehicle stability control switch | VSC OFF | Displayed | Comes on |
| Result | Proceed to |
|---|---|
| Indicator light and mode condition display do not change. | A |
| Mode condition display is normal, but indicator light does not change. | B |
| Indicator light and mode condition display are normal. | C |
A
B
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Select the Active Test on the intelligent tester.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| TRC(TRAC) OFF Indicator Light | Multi-information display (TRC OFF message) | Display (message) ON/OFF | Observe combination meter assembly |
| VSC OFF Indicator Light | VSC OFF indicator light | Indicator light ON/OFF | Observe combination meter assembly |
| Tester Display |
|---|
| TRC(TRAC) OFF Indicator Light |
| Tester Display |
|---|
| VSC OFF Indicator Light |
Check the multi-information display (TRC OFF message) and VSC OFF indicator light in the combination meter assembly turn on or off in accordance with intelligent tester operation.
The multi-information display (TRC OFF message) and VSC OFF indicator light turn on or off in accordance with intelligent tester operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Vehicle Stability Control Switch) |
Turn the engine switch off.
Disconnect the I175 vehicle stability control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 9 (+) - 6 (E) | Switch pushed | Below 1 Ω |
| 9 (+) - 6 (E) | Switch not pushed | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH(for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH(for RHD)>REMOVAL
Disconnect the A49 skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-9 (CSW) - I175-9 (+) | Always | Below 1 Ω |
| A49-9 (CSW) - Body ground | Always | 10 kΩ or higher |
| I175-6 (E) - Body ground | Always | Below 1 Ω |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the engine switch off.
Perform an Active Test of the combination meter assembly using the intelligent tester.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display |
|---|
| Meter Display 1 |
| Tester Display |
|---|
| Indicat. VSC OFF |
Check the combination meter assembly.
The multi-information display and VSC OFF indicator light turn on or off in accordance with intelligent tester operation.
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING