Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.04
RM2030EQ _58 Vehicle Interior _014667 METER / GAUGE / DISPLAY _0074615 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge malfunction via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1500 Fuel Sender Open Detected When IG voltage is 9.5 V or more and the following condition is detected:
1.

Fuel sender gauge operation malfunction


·

Harness or connector

·

Fuel sender gauge assembly

·

Combination meter assembly


- -

WIRING DIAGRAM

E156126E59
5.26,2.938 7.094,3.281 1.833,0.344 10 false Combination Meter Assembly 6.073,0.896 6.313,1.052 0.24,0.156 10 false FR 6.073,2.25 6.365,2.406 0.292,0.156 10 false FE 5.813,0.885 6.188,1.156 0.375,0.271 10 false 14 5.823,2.24 6.156,2.604 0.333,0.365 10 false 15 2.125,2.229 2.24,2.375 0.115,0.146 10 false 3 2.115,0.885 2.229,1.031 0.115,0.146 10 false 2 0.292,3.052 2.063,3.49 1.771,0.438 10 false Fuel Suction Tube Assembly with Pump and Gauge 0.49,1.49 1.125,2.26 0.635,0.771 10 false Fuel Sender Gauge Assembly 1.302,1.427 1.417,1.573 0.115,0.146 10 false 2 1.302,2.094 1.417,2.24 0.115,0.146 10 false 1 1.802,2.24 2.021,2.385 0.219,0.146 10 false FE 1.813,0.885 2.01,1.042 0.198,0.156 10 false FS 5.26,2.771 5.75,3.052 0.49,0.281 10 false I18 0.292,2.885 0.573,3.031 0.281,0.146 10 false N11

PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input signal Min.: 0 L, Max.: 127.5 L Fuel receiver gauge indicates F: 62.9
Fuel receiver gauge indicates 3/4: 54.5
Fuel receiver gauge indicates 1/2: 35.0
Fuel receiver gauge indicates 1/4: 15.4
Fuel receiver gauge indicates E: 7.0
Unit: Liter
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39

Result:
Result Proceed to
Fuel level data can be displayed on the GTS and DTC B1500 is output. A
Fuel level data cannot be displayed on the GTS. B



A

REPLACE COMBINATION METER ASSEMBLY

B

2.INSPECT FUEL SENDER GAUGE ASSEMBLY
2.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.
E224284C69
0.24,1.458 0.698,1.74 0.458,0.281 1.24,2.156 1.24,2.625 1.24,2.625 1.427,2.625 false 1.104,2.156 1.104,2.625 1.104,2.625 0.917,2.625 false 0.115,0.104 0.396,0.385 0.281,0.281 10 false *a 0.688,2.552 1.219,2.792 0.531,0.24 10 false FR 1.49,2.552 2.021,2.792 0.531,0.24 10 false FE 0.365,1.51 0.781,2.146 0.417,0.635 10 false I18
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the I18 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-14 (FR) - I18-15 (FE) Always 13.5 to 414.5 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
a.

Disconnect the N11 fuel suction tube assembly with pump and gauge connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-14 (FR) - N11-2 (FS) Always Below 1 Ω
I18-14 (FR) - Body ground Always 10 kΩ or higher
I18-15 (FE) - N11-3 (FE) Always Below 1 Ω
I18-15 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

5.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
a.

Visually check for deformation on the fuel suction tube assembly with pump and gauge connector.

OK:

There is no deformation.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE