Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2015.04
RM2030EQ _55 Steering _014655 POWER ASSIST SYSTEMS _0077045 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  EPS Warning Light Circuit  


DESCRIPTION

If the power steering ECU assembly detects a malfunction, the EPS warning light comes on. At this time, the power steering ECU assembly stores a DTC in its memory.

WIRING DIAGRAM

C250102E31
0.854,0.646 1.406,0.875 0.552,0.229 10 false CANH 0.875,1.281 1.406,1.49 0.531,0.208 10 false CANL 5.979,0.646 6.49,0.823 0.51,0.177 10 false CANH 5.99,1.281 6.51,1.51 0.521,0.229 10 false CANL 1.354,0.458 1.531,0.625 0.177,0.167 10 false 17 1.365,1.094 1.542,1.26 0.177,0.167 10 false 16 0.271,1.802 0.656,1.958 0.385,0.156 10 false I18 0.271,1.969 2.135,2.25 1.865,0.281 10 false Combination Meter Assembly 0.99,4.365 2.625,4.573 1.635,0.208 10 false CAN Communication Line 4.115,0.635 4.365,0.917 0.25,0.281 10 false Ij2 4.125,1.271 4.427,1.521 0.302,0.25 10 false Ij2 4.094,2.406 4.406,2.656 0.313,0.25 10 false Ij2 5.656,0.448 5.854,0.594 0.198,0.146 10 false 4 5.667,1.083 5.885,1.229 0.219,0.146 10 false 8 5.979,2.448 6.323,2.719 0.344,0.271 10 false IG 5.979,3.26 6.51,3.583 0.531,0.323 10 false PGND 5.667,3.021 5.76,3.177 0.094,0.156 10 false 2 5.177,3.99 7.156,4.25 1.979,0.26 10 false Power Steering ECU Assembly 2.563,2.594 3.469,2.865 0.906,0.271 10 false EPS-IG1 0.229,2.427 1.594,2.615 1.365,0.188 10 false from IG1 NO. 3 Relay 4.115,2.208 4.208,2.365 0.094,0.156 10 false 5 5.656,2.229 5.875,2.375 0.219,0.146 10 false 1 5.656,3.219 5.865,3.448 0.208,0.229 10 false j2 5.646,2.406 5.813,2.708 0.167,0.302 10 false j1 5.667,1.26 5.917,1.615 0.25,0.354 10 false j1 5.656,0.625 5.906,0.927 0.25,0.302 10 false j1 4.125,0.427 4.323,0.615 0.198,0.188 10 false 2 4.125,1.073 4.354,1.24 0.229,0.167 10 false 1 3.604,0.51 4.094,0.698 0.49,0.188 10 false CANH 3.625,1.115 4.042,1.26 0.417,0.146 10 false CANL 3.833,2.323 4.01,2.552 0.177,0.229 10 false IG 4.896,2.542 5.229,2.76 0.333,0.219 10 false *1 4.875,0.76 5.208,0.979 0.333,0.219 10 false *1 4.875,1.385 5.208,1.604 0.333,0.219 10 false *1 4.365,3.365 4.698,3.583 0.333,0.219 10 false *1 0.771,4.021 2.927,4.24 2.156,0.219 10 false *1: ECU Wire Sub-assembly

INSPECTION PROCEDURE

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing (See page Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
a.

Check the connection condition of the ECU wire sub-assembly and power steering ECU assembly connectors.

OK:

The ECU wire sub-assembly and power steering ECU assembly connectors are securely connected.



b.

Check that the ground wire is securely installed with the bolt.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>INSTALLATION

OK:

The ground wire is securely installed with the bolt.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)

NG

CONNECT CONNECTOR OR INSTALL GROUND WIRE

2.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

OK:

DTC is not output.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)
a.
C240359C04
0.458,0.458 0.906,0.74 0.448,0.281 2.531,1.083 2.156,1.219 false 0.135,0.083 0.677,0.427 0.542,0.344 10 *a 2.573,0.979 3.094,1.396 0.521,0.417 10 IG 0.604,0.521 0.969,0.938 0.365,0.417 10 Ij2
*a Front view of wire harness connector
(to ECU Wire Sub-assembly)


Disconnect the Ij2 connector from the ECU wire sub-assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Ij2-5 (IG) - Body ground Ignition switch ON 9 to 16 V



Result:
Proceed to
OK
NG



OK

4.CHECK ECU WIRE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ECU WIRE SUB-ASSEMBLY
a.
C240351C05
0.344,3.271 0.792,3.552 0.448,0.281 0.604,0.906 1.052,1.188 0.448,0.281 2.229,3.552 2.313,4.156 false 1.115,1.677 1.49,1.802 false 0.198,0.146 0.604,0.5 0.406,0.354 10 false *a 0.51,3.333 0.917,3.635 0.406,0.302 10 false j2 2.156,4.198 2.823,4.583 0.667,0.385 10 false PGND 0.917,1.583 1.385,1.906 0.469,0.323 10 false IG 0.781,0.969 1.188,1.333 0.406,0.365 10 false j1
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Connect the Ij2 connector to the ECU wire sub-assembly.


b.

Disconnect the power steering ECU assembly j1 and j2 connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
j1-1 (IG) - Body ground Ignition switch ON 9 to 16 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j2-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY

5.INSPECT COMBINATION METER ASSEMBLY
a.

Reconnect the power steering ECU assembly connector.


b.

Perform the Active Test of the combination meter assembly using the intelligent tester.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. EPS
50004 122 22

c.

Check the combination meter assembly.

OK:

The EPS warning light turns on or off in accordance with the intelligent tester operation.



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY