Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › from 2015.04
RM2030EQ _55 Steering _014656 STEERING COLUMN _0077044 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Unable to Unlock Steering Wheel (Engine cannot Start)  


DESCRIPTION

The steering lock actuator assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if an engine start operation is performed while shaking the steering wheel in the same manner as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly) or ECM is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the engine cannot be started.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Unable to unlock steering wheel (Engine cannot start)
Entry&Start
·

All items

Click here(Click here)


-

WIRING DIAGRAM

C277877E04
2.573,0.406 3.354,0.563 0.781,0.156 10 false from Battery 4.146,0.563 4.969,0.719 0.823,0.156 10 false STRG LOCK 5.365,0.365 5.479,0.521 0.115,0.156 10 false B 5.156,0.292 5.323,0.469 0.167,0.177 10 false 7 5.365,1.094 5.604,1.25 0.24,0.156 10 false LIN 5.146,0.969 5.448,1.167 0.302,0.198 10 false 5 5.365,1.906 5.625,2.063 0.26,0.156 10 false IGE 5.156,1.844 5.313,2.146 0.156,0.302 10 false 3 5.365,2.667 5.698,2.823 0.333,0.156 10 false GND 5.146,2.594 5.333,2.823 0.188,0.229 10 false 1 2.604,1.135 2.844,1.292 0.24,0.156 10 false LIN 2.958,0.948 3.135,1.104 0.177,0.156 10 false 17 2.5,1.948 2.865,2.104 0.365,0.156 10 false SLR+ 2.656,4.042 2.844,4.198 0.188,0.156 10 false P2 2.958,1.771 3.135,1.927 0.177,0.156 10 false 29 2.729,2.667 2.844,2.823 0.115,0.156 10 false P 2.083,1.125 2.479,1.281 0.396,0.156 10 false CANL 2.083,2.104 2.5,2.26 0.417,0.156 10 false CANH 0.771,1.094 1.167,1.25 0.396,0.156 10 false CANL 0.75,2.073 1.167,2.229 0.417,0.156 10 false CANH 2.094,2.667 2.208,2.823 0.115,0.156 10 false E 2.958,2.531 3.135,2.688 0.177,0.156 10 false 25 1.792,0.948 1.969,1.104 0.177,0.156 10 false 15 1.781,1.927 1.958,2.083 0.177,0.156 10 false 14 1.24,0.958 1.417,1.115 0.177,0.156 10 false 13 1.25,1.948 1.427,2.104 0.177,0.156 10 false 14 1.792,2.521 1.969,2.677 0.177,0.156 10 false 11 2.948,1.135 3.292,1.385 0.344,0.25 10 false I78 2.948,1.948 3.313,2.188 0.365,0.24 10 false I78 2.948,2.708 3.396,3.021 0.448,0.313 10 false I78 1.792,1.135 2.156,1.427 0.365,0.292 10 false I78 1.781,2.115 2.115,2.281 0.333,0.167 10 false I78 1.75,2.698 2.146,2.875 0.396,0.177 10 false A43 5.25,3.083 5.667,3.281 0.417,0.198 10 false I24 5.25,3.26 6.469,3.76 1.219,0.5 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 0.25,3.083 0.635,3.396 0.385,0.313 10 false I13 0.25,3.26 1.385,3.76 1.135,0.5 10 false Main Body ECU (Multplex Network Body ECU) 1.76,3.094 3.302,3.417 1.542,0.323 10 false Certification ECU (Smart Key ECU Assembly) 1.25,5.083 3.167,5.75 1.917,0.667 10 false Shift Lock Control ECU (Lower Shift Lever Assembly) 1.25,4.896 1.677,5.146 0.427,0.25 10 false I42 4.479,5.063 6.188,5.219 1.708,0.156 10 false : LIN Communnication Line 4.479,5.385 6.26,5.542 1.781,0.156 10 false : CAN Communnication Line 2.938,3.948 3.031,4.104 0.094,0.156 10 false 3 2.74,4.646 2.854,4.802 0.115,0.156 10 false E 2.938,4.552 3.031,4.708 0.094,0.156 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.

·

Perform either of the following operations to lock/unlock the steering:

·

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.

·

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.


·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, confirm that the problem does not occur.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly), registration must be performed (refer to Service Bulletin).

·

When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.



PROCEDURE

1.CHECK DTC (ALL)

OK

2.CHECK ENGINE SWITCH (SWITCH CONDITION)

NG

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK ENGINE SWITCH (SWITCH CONDITION)
a.

Check the power source mode change.

i.

When the key is inside the vehicle and the shift lever is in P, check that pressing the engine switch with the brake pedal released causes the power source mode to change as follows:

OK:

Off → on (ACC) → on (IG) → off




Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (UNLOCK REQUEST RECEIVE)

NG

GO TO SMART ENTRY AND START SYSTEM (for Start Function) (PROBLEM SYMPTOMS TABLE)

3.READ VALUE USING INTELLIGENT TESTER (UNLOCK REQUEST RECEIVE)
a.

Use the Data List to check if the steering lock request is functioning properly.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Unlock Request Receive Reception state of steering unlock request signal by certification ECU (smart key ECU assembly)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more elapse after receiving the signal, the item changes to "NG".



OK or NG OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
NG: Except above
·

If the unlock signal has not been received, the engine cannot be started.

·

If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Unlock Request Receive
50003 125 67
OK:

Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

4.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

9.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)
4.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

C320284C02
2.083,0.5 2.5,0.75 0.417,0.25 4.719,0.5 5.135,0.75 0.417,0.25 4.583,1.917 4.823,1.365 true 2.417,1.917 2.698,1.344 true 2.177,0.552 2.635,0.75 0.458,0.198 10 false A43 0.167,0.135 0.625,0.333 0.458,0.198 10 false *a 4.833,0.552 5.292,0.75 0.458,0.198 10 false I78 4.531,1.917 4.99,2.115 0.458,0.198 10 false P 2.365,1.917 2.823,2.115 0.458,0.198 10 false E
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Condition Specified Condition
I78-25 (P) - A43-11 (E) Shift lever in P 9 V or higher
I78-25 (P) - A43-11 (E) Shift lever not in P 1.5 V or less



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

7.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL ECU (LOWER SHIFT LEVER ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Disconnect the I24 steering lock ECU connector.


b.
C157850C16
0.395,0.3 0.622,0.476 0.228,0.176 10 *a 0.463,0.968 0.772,1.111 0.309,0.142 10 I24 0.83,1.495 1.188,1.679 0.358,0.184 10 GND 1.299,2.42 1.049,1.676 false 0.341,0.897 0.828,1.19 0.487,0.292 2.252,2.42 2.502,1.676 false 2.468,1.495 2.622,1.679 0.154,0.184 10 B
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the connection which leads to ground.


Standard Voltage:
Tester Connection Condition Specified Condition
I24-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)
a.

Reconnect the I24 steering lock ECU connector.


b.
C241547C11
0.208,0.667 0.625,0.99 0.417,0.323 0.344,2.906 1.719,3.073 1.375,0.167 2.344,2.969 2.75,3.083 0.406,0.115 1.573,4.031 2.531,4.198 0.958,0.167 2.313,1.094 2.729,1.729 false 1.417,2.906 2.906,2.667 2.906,2.667 2.615,2.958 false 2.146,4.198 2.146,4.406 false 1.854,1.073 0.76,1.74 false 0.385,0.115 0.896,0.438 0.51,0.323 10 *a 2.958,2.573 3.208,2.823 0.25,0.25 10 *b 2.073,4.427 2.313,4.646 0.24,0.219 10 *c 0.333,0.75 0.646,0.917 0.313,0.167 10 I24 0.573,1.792 1,2.042 0.427,0.25 10 IGE 2.646,1.75 3.104,1.979 0.458,0.229 10 GND 3.01,4.052 3.385,4.313 0.375,0.26 10 GND
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))
*b Steering lock motor not operating
*c Steering lock motor operating


Check the signal waveform according to the condition(s) in the table below.

Standard Frequency:
Item Content
Tester Connection I24-3 (IGE) - I24-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating


HINT:
·

When taking measurements while the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

·

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.

·

To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.





Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL ECU (LOWER SHIFT LEVER ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the I42 shift lock control ECU (lower shift lever assembly) connector.


b.

Disconnect the I78 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I42-3 (P2) - I78-25 (P) Always Below 1 Ω
I42-3 (P2) - Body ground Always 10 kΩ higher
I78-25 (P) - Body ground Always 10 kΩ higher



Result:
Proceed to
OK
NG



OK

8.INSPECT SHIFT LOCK CONTROL ECU (LOWER SHIFT LEVER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT SHIFT LOCK CONTROL ECU (LOWER SHIFT LEVER ASSEMBLY)
a.

Reconnect the I42 shift lock control ECU (lower shift lever assembly) connector.


b.
C305098C04
0.49,0.979 0.813,1.208 0.323,0.229 2.083,1.719 1.792,1.198 false 0.115,0.104 0.427,0.26 0.313,0.156 10 false *a 0.563,1.01 1,1.333 0.438,0.323 10 false I42 2.135,1.719 2.583,2.021 0.448,0.302 10 false P2
*a Component with harness connected
(Shift Lock Control ECU (Lower Shift Lever Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I42-3 (P2) - Body ground Shift lever in P 9 V or higher
I42-3 (P2) - Body ground Shift lever not in P 1.5 V or less



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

9.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)

OK

10.REPLACE STEERING LOCK ACTUATOR ASSEMBLY

NG

11.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
10.REPLACE STEERING LOCK ACTUATOR ASSEMBLY

OK

END

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

11.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

OK

END

NG

REPLACE STEERING LOCK ACTUATOR ASSEMBLY