While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.
If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for over 20 seconds.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0617 | Starter Relay Circuit High | When all of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):
(a) The vehicle speed is 20 km/h (12.43 mph) or more. (b) The engine speed is 1000 rpm or higher. (c) The STA signal is on. |
·
Starter signal circuit ·
Park/Neutral position switch assembly ·
ECM |
Comes on | DTC stored |
| Required Sensors/Components (Main) | ST relay
Park/Neutral position switch assembly Certification ECU (smart key ECU assembly) Ignition or starter switch assembly |
| Required Sensors/Components (Related) | Vehicle speed sensor
Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Vehicle speed | 20 km/h (12.43 mph) or more |
| Engine speed | 1000 rpm or higher |
| Starter | On |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the tester on [A].
Start the engine.
Idle the engine for 5 seconds or more [B].
Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine / DTC [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0617.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the value displayed on the tester when the vehicle is driven at 20 km/h (12.4 mph) or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
| Condition | Tester Display | Proceed to |
|---|---|---|
| Driving at 20 km/h (12.4 mph) or more | Close (Starter signal off) | A |
| Open (Starter signal on) | B |
A
B
Inspect the park/neutral position switch assembly.
Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/ smart entry and start system) | A |
| OK (w/o smart entry and start system) | B |
| NG | C |
A
B
C
Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Repair or replace harness or connector (park/neutral position switch assembly - ST relay - ECM - certification ECU (smart key ECU assembly)).
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace harness or connector (park/neutral position switch assembly - ST relay - ECM).
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0617 is output | B |
A
B