The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0705 | Transmission Range Sensor Circuit Malfunction (PRNDL Input) | One of the following conditions A, B or C is met (2 trip detection logic):
A. One of the following conditions (a), (b) or (c) is met for 2 seconds or more: (a) Any 2 or more signals of the following are on simultaneously: ·
P input signal ·
R input signal ·
D input signal (b) Any 2 or more signals of the following are on simultaneously: ·
N input signal ·
R input signal ·
D input signal (c) Any 2 or more signals of the following are on simultaneously: ·
NSW input signal ·
R input signal ·
D input signal B. Any of the following conditions is met for 2 seconds or more in the S position: ·
NSW input signal is on ·
P input signal is on ·
N input signal is on ·
R input signal is on C. All switches are off simultaneously for NSW, P, R, N and D for 1 minute or more. |
·
Open or short in park/neutral position switch assembly circuit ·
Short in park/neutral position switch assembly ·
Open or short in transmission control switch circuit ·
Lower shift lever assembly ·
ECM |
Comes on | DTC stored |
These DTCs indicate a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.
The park/neutral position switch assembly detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, R, N, D, or S). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM illuminates the MIL and stores the DTC.
| Required Sensors/Components | Park/Neutral position switch assembly |
| Frequency of Operation | Continuous |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the tester on.
Move the shift lever to R and wait 2 seconds or more.
Move the shift lever to N and wait 2 seconds or more.
Move the shift lever to D and wait 2 seconds or more.
Move the shift lever to S and wait 2 seconds or more.
Move the shift lever to P and wait 2 seconds or more.
Wait 1 minute or more.
Enter the following menus: Powertrain / Engine / DTC.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0705.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
Inspect the fuses for circuits related to this system before performing the following procedure.
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may by discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data.
Read the values displayed on the tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift SW Status (P Range) | Park/Neutral position switch assembly status: | ON or OFF | ·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| Shift SW Status (R Range) | Park/Neutral position switch assembly status: | ON or OFF | ·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| Shift SW Status (N Range) | Park/Neutral position switch assembly status: | ON or OFF | ·
ON: Shift lever in N ·
OFF: Shift lever not in N |
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| Sports Mode Selection SW | Sport mode select switch status: | ON or OFF | ·
ON: Shift lever in S, "+" or "-" ·
OFF: Shift lever not in S, "+" or "-" |
- |
| Shift SW Status (D Range) | Park/Neutral position switch assembly status: | ON or OFF | ·
ON: Shift lever in D or S ·
OFF: Shift lever not in D or S |
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Neutral Position SW Signal and Shift SW Status (R, P, N and D Range).
| Tester Display |
|---|
| Neutral Position SW Signal |
| Shift SW Status (P Range) |
| Shift SW Status (R Range) |
| Shift SW Status (N Range) |
| Shift SW Status (D Range) |
Read the values displayed on the tester.
| Tester Display | Shift Lever Position | Specified Condition |
|---|---|---|
| Neutral Position SW Signal | P or N | ON |
| Except P or N | OFF | |
| Shift SW Status (R Range) | R | ON |
| Except R | OFF | |
| Shift SW Status (P Range) | P | ON |
| Except P | OFF | |
| Shift SW Status (N Range) | N | ON |
| Except N | OFF | |
| Shift SW Status (D Range) | D or S | ON |
| Except D or S | OFF |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Sports Mode Selection SW.
| Tester Display |
|---|
| Sports Mode Selection SW |
Read the values displayed on the tester.
| Tester Display | Shift Lever Position | Specified Condition |
|---|---|---|
| Sports Mode Selection SW | S | ON |
| Except S | OFF |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the transmission control switch.
Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>SHIFT LEVER>REMOVAL
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Shift Lever Position | Condition | Specified Condition |
|---|---|---|---|
| A25-37 (S) - Body ground | S, "+" or "-" | Ignition switch ON | 11 to 14 V |
| Not in S | Ignition switch ON | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Park/Neutral Position Switch Assembly) |
Disconnect the park/neutral position switch assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E77-1 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the park/neutral position switch assembly.
Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E77-7 (DL) - E26-69 (D) | Always | Below 1 Ω |
| E77-8 (NL) - E26-71 (N) | Always | Below 1 Ω |
| E77-2 (RL) - E26-68 (R) | Always | Below 1 Ω |
| E77-3 (PL) - E26-70 (P) | Always | Below 1 Ω |
| E77-4 (B) - E26-65 (NSW) | Always | Below 1 Ω |
| E77-7 (DL) or E26-69 (D) - Body ground | Always | 10 kΩ or higher |
| E77-8 (NL) or E26-71 (N) - Body ground | Always | 10 kΩ or higher |
| E77-2 (RL) or E26-68 (R) - Body ground | Always | 10 kΩ or higher |
| E77-3 (PL) or E26-70 (P) - Body ground | Always | 10 kΩ or higher |
| E77-4 (B) or E26-65 (NSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG