Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › from 2015.04
RM2030EQ _58 Vehicle Interior _014665 THEFT DETERRENT / KEYLESS ENTRY _0074592 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2282  Vehicle Speed Signal Malfunction  B2283  Vehicle Speed Sensor Malfunction  


DESCRIPTION

DTC B2282 is stored when the vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match.

DTC B2283 is stored when a malfunction in the vehicle speed sensor is detected.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2282 Vehicle Speed Signal Malfunction The vehicle speed signal sent by the combination meter assembly via direct line sent and the vehicle speed signal sent via CAN communication (1-trip detection logic*) do not match.
·

AM2 fuse

·

Meter/gauge system

·

Certification ECU (smart key ECU assembly)

·

Junction Connector

·

Wire harness or connector


DTC Output Confirmation Operation

Drive the vehicle for 20 seconds at a vehicle speed of 25 km/h (16 mph) or more, and then drive the vehicle at a vehicle speed of less than 5 km/h (3 mph) for 20 seconds.


B2283 Vehicle Speed Sensor Malfunction Either of the of the following malfunctions is detected (a vehicle speed sensor malfunction is detected) (1-trip detection logic*)
·

Vehicle speed signal malfunction detection 1: Excessive deceleration is detected

·

Vehicle speed signal malfunction detection 2: Engine speed linked detection


·

AM2 fuse

·

Meter/gauge system

·

Certification ECU (smart key ECU assembly)

·

Junction Connector

·

Wire harness or connector


DTC Output Confirmation Operation

Run the engine at an engine speed of 2000 rpm or more for 330 seconds.



*: Only detected while a malfunction is present and the engine switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
DTC Code Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
B2282
·

When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle speed is 0 km/h (0 mph), there is no effect on vehicle behavior.

·

When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the engine switch cannot be turned from on (IG) to off.


-
B2283
·

The power source mode is changed to off (the engine is stopped) by pressing the engine switch while the vehicle is being driven.

·

With the electrical key transmitter sub-assembly in the cabin, even if an engine start operation is performed, the engine does not start.


-

WIRING DIAGRAM

B407408E01
0.438,1.438 1.552,1.635 1.115,0.198 10 false Skid Control ECU 2.906,1.219 4.531,1.417 1.625,0.198 10 false CAN Communication Line 0.177,2.75 3.021,2.948 2.844,0.198 10 false Certification ECU (Smart Key ECU Assembly) 5.302,2.792 7.156,2.979 1.854,0.188 10 false Combination Meter Assembly 0.51,4.156 3.063,4.354 2.552,0.198 10 false Stereo Component Amplifier Assembly*5 5.417,4.177 7.156,4.365 1.74,0.188 10 false Radio Receiver Assembly*1 4.573,5.615 7.115,5.969 2.542,0.354 10 false Navigation Receiver Assembly*2 or Radio and Display Receiver Assembly*3 3.094,7.531 4.833,7.719 1.74,0.188 10 false Junction Connector 4.844,7.49 7.115,7.677 2.271,0.188 10 false Windshield Wiper Relay Assembly*4 0.25,7.979 2.521,8.167 2.271,0.188 10 false *1: for Radio Receiver Type 2.5,8 4.771,8.188 2.271,0.188 10 false *2: for Navigation Receiver Type 4.833,8 7.104,8.188 2.271,0.188 10 false *3: for Radio and Display Type 0.25,8.333 2.521,8.521 2.271,0.188 10 false *4: w/ Auto Wiper System 2.5,8.333 4.771,8.521 2.271,0.188 10 false *5: for 10 Speakers 1.188,7.521 1.479,7.698 0.292,0.177 10 false A25 1.542,7.521 1.854,7.698 0.313,0.177 10 false ECM 2.76,7.531 3.052,7.708 0.292,0.177 10 false I185 4.594,7.49 4.885,7.667 0.292,0.177 10 false I72 5.354,7.094 5.646,7.271 0.292,0.177 10 false 24 5.583,7.094 5.875,7.271 0.292,0.177 10 false SPD 5.583,5.198 5.875,5.375 0.292,0.177 10 false SPD 5.583,3.771 5.875,3.948 0.292,0.177 10 false SPD 1.719,3.771 2.01,3.948 0.292,0.177 10 false SPD 1.719,5.208 2.01,5.385 0.292,0.177 10 false SPD 1.74,7.094 2.031,7.271 0.292,0.177 10 false SPD 3.948,7.094 4.24,7.271 0.292,0.177 10 false 20 2.927,7.094 3.219,7.271 0.292,0.177 10 false 16 2.094,7.094 2.385,7.271 0.292,0.177 10 false 10 1.26,5.625 1.552,5.802 0.292,0.177 10 false E7 1.5,5.625 1.813,5.802 0.313,0.177 10 false TCM 2.094,5.208 2.385,5.385 0.292,0.177 10 false 3 5.229,5.302 5.521,5.479 0.292,0.177 10 false I155 4.917,5.302 5.208,5.479 0.292,0.177 10 false I67 4.854,5.104 5.146,5.281 0.292,0.177 10 false 17*2 5.219,5.104 5.51,5.281 0.292,0.177 10 false 17*3 5.094,4.177 5.385,4.354 0.292,0.177 10 false I150 5.354,3.771 5.646,3.948 0.292,0.177 10 false 17 3.948,3.771 4.24,3.948 0.292,0.177 10 false 17 2.938,3.771 3.229,3.948 0.292,0.177 10 false 19 0.292,4.156 0.583,4.333 0.292,0.177 10 false I69 2.094,3.771 2.385,3.948 0.292,0.177 10 false 11 1.719,2.344 2.01,2.521 0.292,0.177 10 false SPD 0.646,2.052 0.938,2.229 0.292,0.177 10 false A43 2.104,2.052 2.396,2.229 0.292,0.177 10 false A43 2.146,2.438 2.438,2.615 0.292,0.177 10 false I78 0.688,1.854 0.979,2.031 0.292,0.177 10 false 11 2.188,1.854 2.479,2.031 0.292,0.177 10 false 2 2.156,2.25 2.448,2.427 0.292,0.177 10 false 27 0.99,2.063 1.281,2.24 0.292,0.177 10 false E 1.813,2.052 2.104,2.229 0.292,0.177 10 false +B 2.927,2.344 3.219,2.521 0.292,0.177 10 false 15 3.948,2.344 4.24,2.521 0.292,0.177 10 false 18 5.406,2.344 5.698,2.521 0.292,0.177 10 false 3 5.583,2.448 5.875,2.625 0.292,0.177 10 false +S 5.063,2.792 5.354,2.969 0.292,0.177 10 false I18 2.542,2.188 2.875,2.365 0.333,0.177 10 false AM2 3.354,1.656 4.198,1.896 0.844,0.24 10 false from Battery 0.115,1.438 0.406,1.615 0.292,0.177 10 false A49 0.875,0.583 1.25,0.76 0.375,0.177 10 false SP1 1.219,0.583 1.51,0.76 0.292,0.177 10 false 2 5.427,0.573 5.719,0.75 0.292,0.177 10 false 4 5.583,0.677 5.958,0.854 0.375,0.177 10 false SI

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to a pulse signal at the transistor in the combination meter. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in an ECU, all systems in the diagram above will not operate normally.



CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2282
B2283
Power Source Control
·

Vehicle Speed Signal

·

Engine Condition

·

Power Supply Condition


Starting Control
·

Engine Speed


Combination Meter
·

Vehicle Speed Meter


-


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Check the Data List for proper functioning of the vehicle speed signal.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost same as actual vehicle speed (Speedometer tester) -
Body Electrical > Combination Meter > Data List
Tester Display
Vehicle Speed Meter
50003 122 8
OK:

Vehicle speed displayed on the intelligent tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER

NG

GO TO METER / GAUGE SYSTEM (Speedmeter Malfunction)

2.READ VALUE USING INTELLIGENT TESTER
a.

Enter the following menus: Body / Power Source Control / Data List.


b.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Signal Vehicle being driven or stopped Stop or Run Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more
-
Body Electrical > Power Source Control > Data List
Tester Display
Vehicle Speed Signal
50003 223 16
OK:

Stop (vehicle is stopped) and Run (vehicle is running) appear on the screen.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

4.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

4.CHECK HARNESS AND CONNECTOR (GROUND)

OK

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY)
a.

Disconnect the I78 connector from the certification ECU (smart key ECU assembly).


b.

Disconnect the I18 connector from the combination meter assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I78-27 (SPD) - I18-3 (+S) Always Below 1 Ω
I78-27 (SPD) or I18-3 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)
6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the I78 certification ECU (smart key ECU assembly) connector.

B274541C10
2.125,0.26 2.521,0.521 0.396,0.26 4.771,0.26 5.167,0.521 0.396,0.26 2.698,1.219 2.531,1.781 false 4.667,1.24 4.844,1.792 false 0.104,0 0.333,0.229 0.229,0.229 10 *a 4.479,2.833 4.917,3.063 0.438,0.229 10 GND 2.479,1.823 2.917,2.052 0.438,0.229 10 E 4.729,1.813 5.167,2.042 0.438,0.229 10 SPD 2.208,0.292 2.552,0.521 0.344,0.229 10 A43 4.896,0.292 5.24,0.521 0.344,0.229 10 I78
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -



b.

Reconnect the I18 combination meter assembly connector.


c.

Connect an oscilloscope to terminal I78-27 (SPD) and A43-11 (E).


d.

Turn the engine switch on (IG).


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tester Connection I78-27 (SPD) - A43-11 (E)
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Engine switch on (IG), vehicle being driven at approximately. 5 km/h (3 mph)

OK:

The waveform is similar to that shown in the illustration.


HINT:

The wavelength becomes shorter as the vehicle speed increases.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

GO TO METER / GAUGE SYSTEM (Speed Signal Circuit)

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the I185 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-3 (+S) - I185-18 Always Below 1 Ω
I18-3 (+S) or I185-18 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I78-27 (SPD) - I185-15 Always Below 1 Ω
I78-27 (SPD) or I185-15 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR