Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM J

2AR-FXE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the power switch is turned on (IG), auxiliary battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil of the No. 1 integration relay (EFI MAIN relay), closing the contact and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

A268320E03
5.427,0.885 5.698,1.042 0.271,0.156 10 false A39 1.854,3.083 1.958,3.219 0.104,0.135 10 false 1 2.573,4 3.208,4.167 0.635,0.167 10 false EFI MAIN 5.542,1.792 5.729,1.958 0.188,0.167 10 false 37 5.854,2.375 6.135,2.521 0.281,0.146 10 false +B2 5.854,2.833 6.063,2.979 0.208,0.146 10 false +B 5.854,3.729 6.281,3.875 0.427,0.146 10 false MREL 5.854,1.875 6.26,2.021 0.406,0.146 10 false IGSW 5.854,4.271 6.073,4.417 0.219,0.146 10 false E1 6.188,4.656 6.677,4.854 0.49,0.198 10 false ECM 2.792,2.615 3.073,2.781 0.281,0.167 10 false IG2 0.677,2.104 1.313,2.271 0.635,0.167 10 false IG2-MAIN 0.51,4.604 1.146,4.958 0.635,0.354 10 false Auxiliary Battery 5.75,0.885 7.031,1.219 1.281,0.333 10 false Power Management Control ECU 5.49,1.958 5.76,2.115 0.271,0.156 10 false A25 1.802,3.281 2.104,3.448 0.302,0.167 10 false 1B 1.833,1.792 2.021,1.958 0.188,0.167 10 false 3 3.542,2.104 4.156,2.458 0.615,0.354 10 false ECU-IG2 NO.3 2.302,4.469 3.75,4.635 1.448,0.167 10 false No. 1 Integration Relay 0.49,3.448 1.479,3.615 0.99,0.167 10 false EFI-MAIN NO.1 0.385,3.979 0.76,4.146 0.375,0.167 10 false MAIN 1.833,3.542 1.969,3.708 0.135,0.167 10 false 2 1.813,3.719 2.115,3.885 0.302,0.167 10 false 1E 1.792,1.958 2.094,2.125 0.302,0.167 10 false 1D 3.542,1.438 3.708,1.583 0.167,0.146 10 false 8 3.417,1.656 3.719,1.823 0.302,0.167 10 false 1C 4.344,1.802 4.448,1.938 0.104,0.135 10 false 1 4.302,1.958 4.604,2.125 0.302,0.167 10 false 1C 4.302,2.656 4.521,2.823 0.219,0.167 10 false 10 4.313,2.833 4.615,3 0.302,0.167 10 false 1C 4.344,3.115 4.51,3.292 0.167,0.177 10 false 9 4.313,3.292 4.615,3.458 0.302,0.167 10 false 1C 4.344,3.542 4.563,3.698 0.219,0.156 10 false 7 4.313,3.719 4.615,3.885 0.302,0.167 10 false 1C 5.813,0.365 6.219,0.51 0.406,0.146 10 false IG2D 5.552,2.198 5.74,2.365 0.188,0.167 10 false 3 5.49,2.365 5.76,2.521 0.271,0.156 10 false A25 5.563,2.677 5.75,2.844 0.188,0.167 10 false 2 5.5,2.833 5.771,2.99 0.271,0.156 10 false A25 5.521,3.552 5.708,3.719 0.188,0.167 10 false 46 5.49,3.719 5.76,3.875 0.271,0.156 10 false A25 5.552,4.063 5.74,4.229 0.188,0.167 10 false 16 5.49,4.25 5.76,4.406 0.271,0.156 10 false E28 3.292,3.427 3.917,3.729 0.625,0.302 10 false EFI NO.2 5.615,0.271 5.802,0.438 0.188,0.167 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E28-16 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (IGSW VOLTAGE)
A255690C49
0.583,1.052 0.917,1.313 0.333,0.26 1.865,1.375 1.719,1.927 false 0.708,0.115 0.875,0.292 0.167,0.177 10 false *a 0.635,1.104 0.969,1.406 0.333,0.302 10 false A25 1.594,1.958 2,2.104 0.406,0.146 10 false IGSW
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A25-37 (IGSW) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN RELAY)

NG

6.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
3.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN RELAY)
a.

Inspect the No. 1 integration relay (EFI MAIN relay).

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-9 - A25-2 (+B) Always Below 1 Ω
1C-10 - A25-3 (+B2) Always Below 1 Ω
1C-7 - A25-46 (MREL) Always Below 1 Ω
1C-9 or A25-2 (+B) - Body ground Always 10 kΩ or higher
1C-10 or A25-3 (+B2) - Body ground Always 10 kΩ or higher
1C-7 or A25-46 (MREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)
A260483C04
0.677,1.188 1,1.458 0.323,0.271 0.76,1.25 1.083,1.417 0.323,0.167 10 false 1B 0.167,0.083 0.406,0.229 0.24,0.146 10 false *a
*a Front view of wire harness connector
(to No. 1 Integration Relay)


a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1B-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - NO. 1 INTEGRATION RELAY)

6.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
a.

Inspect the No. 1 integration relay (IG2 relay).

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (IG2 RELAY)

7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - A25-37 (IGSW) Always Below 1 Ω
1C-1 or A25-37 (IGSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)
A256530C05
0.729,1.146 1.042,1.375 0.313,0.229 0.146,0.052 0.354,0.219 0.208,0.167 10 false *a 0.813,1.188 1.083,1.354 0.271,0.167 10 false 1D
*a Front view of wire harness connector
(to No. 1 Integration Relay)


a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1D-3 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - NO. 1 INTEGRATION RELAY)

9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)
a.

Disconnect the power management control ECU connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-2 (IG2D) - 1C-8 Always Below 1 Ω
A39-2 (IG2D) or 1C-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR