Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM › 2012.02–2015.04
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM J

2AR-FXE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the power switch is turned on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the power switch is turned on (IG), the MIL should be illuminated and should turn off after power switch on (READY). If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A268324E03
1.385,3.729 1.688,3.885 0.302,0.156 10 false A39 2.323,3.156 2.417,3.313 0.094,0.156 10 false 2 1.635,1.479 1.875,1.635 0.24,0.156 10 false IG2 1.385,3.906 2.646,4.281 1.26,0.375 10 false Power Management Control ECU 0.344,2.51 1.021,2.656 0.677,0.146 10 false IG2-MAIN 0.469,3.667 1.115,4.052 0.646,0.385 10 false Auxiliary Battery 1.229,2.188 2.979,2.385 1.75,0.198 10 false No. 1 Integration Relay 1.896,3.271 2.281,3.427 0.385,0.156 10 false IG2D 0.188,2 0.385,2.156 0.198,0.156 10 false 1D 0.302,1.833 0.396,1.99 0.094,0.156 10 false 3 0.979,2 1.177,2.156 0.198,0.156 10 false 1E 1.094,1.771 1.188,1.927 0.094,0.156 10 false 2 2.885,0.833 3.083,0.99 0.198,0.156 10 false 1C 2.948,0.656 3.042,0.813 0.094,0.156 10 false 5 2.74,2 2.938,2.156 0.198,0.156 10 false 1C 2.854,1.76 2.948,1.917 0.094,0.156 10 false 8 3.385,0.99 4.156,1.146 0.771,0.156 10 false METER-IG2 4.115,0.75 4.313,0.906 0.198,0.156 10 false 13 4.354,0.969 4.615,1.125 0.26,0.156 10 false IG+ 5.271,0.75 5.448,0.906 0.177,0.156 10 false 22 4.823,0.979 5.146,1.135 0.323,0.156 10 false CHK 6.458,3.74 6.781,3.896 0.323,0.156 10 false ECM 6.115,3.74 6.385,3.896 0.271,0.156 10 false A25 0.365,3.094 0.74,3.24 0.375,0.146 10 false MAIN 4.219,1.323 4.521,1.479 0.302,0.156 10 false I18 4.219,1.49 5.479,1.865 1.26,0.375 10 false Combination Meter Assembly 5.823,0.74 6,0.896 0.177,0.156 10 false 30 6.073,0.74 6.25,0.896 0.177,0.156 10 false W

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.


Result:
Result Proceed to
MIL remains ON A
MIL does not illuminate B



A

2.CHECK WHETHER DTC OUTPUT RECURS

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Check if any DTCs have been detected. Note down any DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC is not detected A
Any DTCs are detected B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.



A

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.
A255690C50
0.583,0.969 0.99,1.25 0.406,0.281 0.177,0.135 0.521,0.396 0.344,0.26 10 false *a 0.667,1.031 1.073,1.313 0.406,0.281 10 false A25
*a Front view of wire harness connector
(to ECM)


Disconnect the A25 ECM connector.


b.

Turn the power switch on (IG).


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-22 (CHK) or A25-30 (W) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the power switch is turned on (IG).

OK:

MIL should be illuminated.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 236 2103

e.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The tester cannot communicate with the ECM.




A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-22 (CHK) - A25-30 (W) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR