Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM J

2AR-FXE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the auxiliary battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A240424E31
4.375,1.115 6.198,1.292 1.823,0.177 10 false 5 V Constant Voltage Circuit 5.354,1.958 6.365,2.375 1.01,0.417 10 false Microprocessor 1.344,1.49 2.813,1.635 1.469,0.146 10 false from EFI NO. 2 Fuse 1.344,1.125 2.688,1.292 1.344,0.167 10 false from EFI NO. 1 Fuse 2.865,0.99 3.385,1.208 0.521,0.219 10 false BATT 0.802,2.323 2.615,2.875 1.813,0.552 10 false Throttle Position Sensor, etc. (Sensors which have ICs) 0.375,2.979 2.635,3.698 2.26,0.719 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.073,3.115 4.333,3.323 0.26,0.208 10 false R 2.854,1.365 3.781,1.563 0.927,0.198 10 false +B, +B2 3.156,2.281 3.448,2.51 0.292,0.229 10 false VC 4.885,3.354 5.333,3.583 0.448,0.229 10 false ECM

When the VC circuit is short-circuited, the microprocessor in the ECM and the sensors that are supplied with power through the VC circuit are inactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated when the power switch is turned on (IG). The MIL goes off when the power switch on (READY).


WIRING DIAGRAM

A261346E02
2.448,0.323 2.542,0.479 0.094,0.156 10 false 5 2.156,0.417 2.417,0.594 0.26,0.177 10 false VC 2.448,0.688 2.542,0.844 0.094,0.156 10 false 3 2.177,0.76 2.365,0.917 0.188,0.156 10 false E2 2.448,1.052 2.542,1.208 0.094,0.156 10 false 6 2.083,1.135 2.375,1.292 0.292,0.156 10 false VTA 2.448,1.417 2.542,1.573 0.094,0.156 10 false 4 5.167,0.323 5.417,0.479 0.25,0.156 10 false 125 5.167,0.698 5.417,0.854 0.25,0.156 10 false 126 5.167,1.052 5.417,1.208 0.25,0.156 10 false 127 5.167,1.417 5.417,1.573 0.25,0.156 10 false 128 5.5,0.323 5.885,0.479 0.385,0.156 10 false VCTA 5.5,0.688 5.792,0.844 0.292,0.156 10 false ETA 5.5,1.135 5.865,1.292 0.365,0.156 10 false VTA1 5.5,1.5 5.865,1.656 0.365,0.156 10 false VTA2 2,1.5 2.365,1.656 0.365,0.156 10 false VTA2 0.427,1.823 0.698,1.979 0.271,0.156 10 false E16 0.427,1.99 2.635,2.25 2.208,0.26 10 false Throttle with Motor Body Assembly 2.448,2.635 2.542,2.792 0.094,0.156 10 false 3 2.146,2.719 2.365,2.875 0.219,0.156 10 false VC 2.448,3 2.542,3.156 0.094,0.156 10 false 2 2.073,3.083 2.365,3.24 0.292,0.156 10 false VVI- 2.448,3.365 2.542,3.521 0.094,0.156 10 false 1 5.167,2.635 5.417,2.792 0.25,0.156 10 false 113 5.167,3 5.417,3.156 0.25,0.156 10 false 114 5.24,3.365 5.417,3.521 0.177,0.156 10 false 82 5.5,2.635 5.885,2.792 0.385,0.156 10 false VCV1 5.5,3 5.833,3.156 0.333,0.156 10 false VV1- 5.5,3.448 5.865,3.604 0.365,0.156 10 false VV1+ 2.031,3.448 2.354,3.604 0.323,0.156 10 false VVI+ 0.688,3.771 0.958,3.927 0.271,0.156 10 false E55 0.688,3.938 2.313,4.094 1.625,0.156 10 false Camshaft Position Sensor 2.448,4.677 2.542,4.833 0.094,0.156 10 false 3 2.146,4.771 2.365,4.927 0.219,0.156 10 false VC 2.448,5.042 2.542,5.198 0.094,0.156 10 false 1 2.177,5.135 2.365,5.292 0.188,0.156 10 false E2 2.448,5.406 2.542,5.563 0.094,0.156 10 false 2 5.24,4.677 5.417,4.833 0.177,0.156 10 false 78 5.24,5.042 5.417,5.198 0.177,0.156 10 false 80 5.24,5.406 5.417,5.563 0.177,0.156 10 false 79 5.5,4.677 6.01,4.896 0.51,0.219 10 false VCPM 5.5,5.042 5.917,5.208 0.417,0.167 10 false EPIM 5.5,5.49 5.875,5.646 0.375,0.156 10 false PIM 2.094,5.5 2.365,5.656 0.271,0.156 10 false PIM 0.396,5.813 0.667,5.969 0.271,0.156 10 false E25 0.396,5.979 2.615,6.135 2.219,0.156 10 false Manifold Absolute Pressure Sensor 5.698,6.24 6.01,6.448 0.313,0.208 10 false E28 6.063,6.24 6.385,6.396 0.323,0.156 10 false ECM

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when the power switch is turned on (IG).

OK:

MIL lights up.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Check the communication between the tester and ECM.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

3.CHECK MIL (THROTTLE POSITION SENSOR)

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle with motor body assembly connector.


b.

Turn the power switch on (IG).


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B


HINT:

Perform "Inspection After Repair" after replacing the throttle with motor body assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




A

4.CHECK MIL (CAMSHAFT POSITION SENSOR)

B

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

4.CHECK MIL (CAMSHAFT POSITION SENSOR)
a.

Disconnect the camshaft position sensor connector.


b.

Turn the power switch on (IG).


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

5.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

5.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the power switch on (IG).


c.

Check the MIL.


Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B



A

6.CHECK HARNESS AND CONNECTOR

B

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

6.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle with motor body assembly connector.


b.

Disconnect the camshaft position sensor connector.


c.

Disconnect the manifold absolute pressure sensor connector.


d.

Disconnect the ECM connectors.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E28-125 (VCTA) - Body ground Always 10 kΩ or higher
E28-113 (VCV1) - Body ground Always 10 kΩ or higher
E28-78 (VCPM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR